RX3 Police Chase Sydney West
RX3 13B Peripheral Port Rotory motor 400HP Police chase.Skip to the chase
it starts at 4.35 sec.
"Attention all", to this day the report of this police chase cannot be
revealed or explained in full detail, what occurred on that day after
the hit accident was even bigger than the chase itself. This video was
edited for public viewing only...
20B ROTARY ACTION! 20B DATSUN 1200 & 20B MAZDA RX3 - TNT 28/12/2013
On the final Test and tune at Willowbank Raceway for the year, Brad Mcilroy
was out testing his Mazfix prepped 20b Datsun 1200 ute as well as Russ in
his 20B powered Mazda Rx3. The PRODAT was testing some changes in the rear
end, keeping the newly added 10.5 inch tyres as well as some changes to the
4 link, and after a few tweaks had the car complete a full pass of 7.95 @
165 mph with a small back off down the deep end, a little slower then what
the car has run but a little more stable down the track. The Mazda Rx3 had
some issues most of the night but managed to get it down the track for an 8
second pass, also off its best, but once sorted should be back down to
where it was running before.
Allen's RX3 Revving at the 12/15/07 Rotary Meet
Mazda RX3 tags the wall - MRHELI
King of the 2-step, Frank 'Mr Heli' Canistra hasn't raced the RX3 in some 2
years. The 13B rotary turbo powered
Mazda sedan ran strong all day going into the low 8s but got loose late in
the night. Frank did a great job of steering out of what could have been a
heavier hit and the good news is that he walked away unhurt.
APSA Pro Street Shootout round 3, Sydney Dragway, Australia - May 18th
Harley on race gas
My dad starts his harley and rides off pretty fast. The bike has screaming
eagle heads, high performance cams, high compression pistons and more.
SCREAMING 20B rotary engine dyno ~ JPC
Centreline Suspension's 20B PP rotary engine from their Mazda RX-7 Sports
Sedan circuit racer on the Dyno at JPC.
The Mazda Rotary Engine Part 1
Educational film by Toyo Kogyo about the Mazda Rotary Engine. Shows how the
Rotary engine works with comparisons to the Piston Engine. Also shows the
Mazda RX500 test vehicle on a banked circuit and the Mazda Cosmo Sport (or
110S). Originates from the late 60's.
RX3 crash - The Godfather
Sam Sadek was very lucky to walk away from this big accident at close to
200mph. The PAC Performance Godfather Mazda RX3 is powered by a 20B turbo rotary engine.
APSA Pro Street Shootout, Sydney Dragway - May 18th 2013.
Part 12: 13B Rotary Engine Rebuild - My 76 Mazda RX-5 Cosmo Restoration
Just as I promised last episode, it is finally time to build the engine!
Part 12 of my RX-5 Cosmo restoration covers the entire process of building
the 6 port 13B Mazda rotary engine. While this engine is a hybrid of GSL-SE
RX-7 and Cosmo parts, the process is the same for any rotary from a 12A to
a 13B NA, 13B turbo, 13B-REW or any
other variant of the 13B. This video shows the whole process of the engine
build, starting from measuring the rotors and covering everything else
including clearancing the side seals, assembling the rotors, complete
assembly the short block, setting the eccentric shaft end play and
installing the front cover and everything underneath it. It's probably the
most complete engine build video outside of what you can buy from the
vendors, and as such, is an hour long. After this one, I'm going back to
videos under 20 minutes. But for now, grab a beverage of your choice, sit
back, and enjoy.
Mazda RX3 Engine Rebuild
1972 Mazda RX3 10A Rotary Wankel Engine starting for the first time after I
did a full engine rebuild which included:- Rotor tips, side seals, corner
seals, oil control rings, rubber oil control ring seals, both rotor
housings and oil pump plus all springs. This is how it started after all of
that. Not bad huh?