406, 5.7 rods, vortec bowtie large port 215cc heads, 66cc chambers, forged flat tops, 11 to 1 comp., isky solid roller, 272@.050 with .505 lift, corrected to .539 with 1.6 roller rockers, pro products hurricane intake, holley 750 double pumper, super comp 1 3/4 headers, full 3 inch Exhaust with h-pipe and flowmasters. Currently has run a best of 7.17 @ 96mph 1/8 mile on 93 pump gas. Best standing 1/4 of 11.40 @ 118mph.
4X4 Chevy Van, 1 Ton, 406, at 5A in Scottsmoor FL
1979 Chevy Van with 1 ton 4X4 drivetrain, 40 inch Bogger tires and powered
by a high performance 406 small block. Also equipped with a wheelchair lift
and hand controls for a quadriplegic driver. Mudding at 5A Scottsmoor.
The Beast 406 ci. S-10
1982 chevy s-1o 400ci., bored .30,over Flat top piston,forged internals,292
comp. cam, 441 heads,port and polished,alum. intake,650
edlbrk.carb,more.... http://community.webshots.com/user/Carkrazy12 Check
out my Cars....!!!
My 1975 Camaro
New additions are weld draglites 15x10's on back skinnies up front, 650
holley vacuum secondary carb instead of the 750 double pumper shown here,
motor has been completely rebuilt since video, back end sits a little bit
1988 Monte Carlo SS full Roller 406 SBC
This is the full Roller SBC that powers my 1988 Monte Carlo SS. It's a
10.5:1 406 SBC, with AFR 210 Comp ported heads, Hurricane intake, SMI 850
double pumper (in the video, before SMI was delivered, I had on Holley VS
750 with Proform main body), custom Howards solid roller cam, Forged bottom
end, billet splayed cap block, and Hooker long tubes. Base of carb got
cracked as you can hear in video. Also don't laugh too hard at the garden
hose connecting the water ports, couldn't find my pipe plugs at the time
LOL. Engine made 602 hp @ 6600 and 571 lbft @ 4800 at the crank.
406 cid Small Block Chevy Engine Dyno
A 400 Small Block Chevy based engine we built featuring AFR heads, an
Edelbrock Victor Jr. intake, Probe pistons, a fully forged rotating
assembly, and an ATI Super damper. It will be going into a Camaro.
new 383 chevy idle 4/7 cyc swap
just fired up my new motor cant wait for the fist ford and spring this
motor has a 4 7 swap and a full roller cam built on a 900 circle
MONTE CARLO 83 ALL BLACK 406 SBC BIG CAM IDLE AND REV...
Chevy 406cu in 6.7L with holley 750cfm, intake performer rpm, flat top
0.030 oversize piston, ported heads, big mutha thumpr comp cam!!!, hookers
headers super competition 13/4", dual Exhaust with flowmaster super 44, 3.42 posi
gear, 3.73 coming next summer and th350 shift kit with stall 3200. Set up
around 400 hp / 400 lb torque. A BEAST TO DRIVE! 1/4mile : 13.4 @ 101mph
with timming around 30° only. with 3.73 gear and 34° timming it will be
around 13.1 / 13 flat with street tire.
Camaro 406 launch vid
Testing my car on the street with new 406. Comes out ok, had to feather it
a little. With some water and a little less tire pressure it should come
out hard. Current best 1/8 mile of 7.17 @ 96mph, best 1/4 of 11.40 @
1988 Chevy Monte Carlo 305 Vortec Wheezy Breezy Project
[Project Wheezy Breezy]
Dads 1988 Monte Carlo LS Small Block Chevy 305 bored .040 over (313c.i)
with ported Vortec heads & custom 1.98 intake valve, with small Comp
Hydraulic Roller Cam 230/230 Duration @50 .510 Lift on a 108 Lobe Sep. Air
Gap Intake, 670 Holley Double Pumper Carb, Comp ProMag Roller Rockers,
Summit Ignition Box with MSD Distributor & Coil, 1'' 5/8 Headers, Full (2
1/2'') H-Pipe Exhaust into Dual 40
Series Flowmaster Mufflers. PA turbo 350
Transmission B&M HoleShot 3600 stall & 4.56 Gears, Edlelbrock Suspension in
Getting prepped for paint booth with SS front clip.
This is just something we did for fun to see what kind of power we could
get out of a small cubic inch 305 with just some spare parts we had lying