Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

Fuel Filter Replacement Acura Legend

This video shows you how to, remove and install a new fuel filter in your 86-95 model Acura Legend. The video cuts out right at the very end, but it shouldn't prevent you from being able to do the job. It's a pretty easy job to replace your fuel filter in this car. Click here to show thanks, and help support Fixbook: http://www.hondahowto.com/p/blog-page_25.html Click this link to Subscribe: http://www.youtube.com/subscription_center?add_user=Hondahowto1&annotation_id=annotation_59253&feature=iv&src_vid=QSNjtNYuD18 Click here to check out the the "Car Runs on 2 cylinders" series: https://www.youtube.com/playlist?list=PLoA1-alJGwfnWZvOZtIjPnQX88q1n3GWA&feature=view_all I, Jordan, assume no liability for anything you choose to do to your car, before, or after watching one of my videos, including this one. All DIY repairs, or modifications, you perform to your car are made at your own risk. Sometimes, even if you've done everything the right way, you can destroy, or damage, a piece, or part. You must understand this; part of doing a repair, and/or modification is messing up sometimes. Also, if for some reason, I do give incorrect instructions, and something breaks because you followed my instructions, I still will not reimburse, or pay, in any way, for whatever cost that may be incurred due to following my wrong instructions. Don't do anything to your car unless you yourself feel comfortable, & confident in doing so. Fixbook DIY Car Repair


 


More Videos...


How To Pull Honda Codes Without a Scanner -EricTheCarGuy
Link to code explanations: http://www.ericthecarguy.com/hondaacura-obd-i-codes-1992-1995 Honda ABS Codes 1994-1997: http://www.ericthecarguy.com/honda-abs-codes-1994-to-1997 Honda ABS Codes 1998 and up: http://www.ericthecarguy.com/honda-abs-codes-1998-to-now Visit me at: http://www.ericthecarguy.com/ Discussion about this Video: http://www.ericthecarguy.com/component/kunena/18-The-EricTheCarGuy-Video-Fo rum/34741-Pulling-Honda-Codes-Without-a-Scanner?Itemid=0#34741 I feel like I should have made this video a while ago but the opportunity never came up. Since I had this RL in my shop that had a check engine light AND an ABS light I thought it was a perfect opportunity to put this video together. I get asked all the time about my 'special tool' and it's really nothing more than a Honda 2 pin connector with the input wires soldered together. These connectors might be harder to find than you think but if you run across a junk honda and one of these is on the harness grab it. Even if you don't have the tool a paper clip or piece of wire will do the exact same thing so don't sweat it if you don't have the tool because shorting the connector is all you need to do. I hope you find this video helpful. Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Acura Legend Stereo Removal 1991-1996
F R E E - R E P A I R - E S T I M A T E S http://CarStereoHelp.com/acura.htm





How to replace a fuel filter Integra
How to replace a fuel filter in a 1992 Acura Integra or most any Honda, Acura, etc.





Honda No Start? POSSIBLE Main Relay - EricTheCarGuy
Honda No Start? POSSIBLE Main Relay - EricTheCarGuy http://www.ericthecarguy.com/default.aspx Here is a GREAT website article about soldering these I strongly suggest you check this out before doing this repair. http://techauto.awardspace.com/mainrelay.html The first of the "Quick Tips". I think I'm going to throw one of these in from time to time to keep things lively. So if you have a Honda or Acura that is not starting DUE TO LOSS OF FUEL PRESSURE this is a good place to start. You may be able to repair the main relay normally found under the dash on the drivers side. If this helps great remember me fondly and pass my name along because I just saved you at the very least about $80, at the most $200. I will be upgrading my website very soon, in fact I will post a video when it is up. Cool new things on the horizon for ETCG and YOU the viewer. So if you want take a look at the old site because it's days are numbered. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Till next time Be Safe and Stay Dirty. Oh yea, and have fun too. ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Honda Accord Fuel Filter Replacement
A fastener by fastener tutorial for replacing the fuel filter on a 1997 Honda Accord. This process applies to Accords manufactured from 1994 to 1997. Honda recommends replacement once every 2 years or 40,000 miles whichever comes first. While I have found many videos on replacing the fuel filters on the easier Civics I have understandably seen none for the Accords. The main reasoning being they are buried deep and are difficult to access and unless you know which tools to use they can look almost impossible to remove. I'll take you through it step by step and show you what tools you'll need to get the job done. Intro and outro music Welcome To The Show by Kevin Macleod (Incompetech.com). Due to factors beyond the control of Bushougoma, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. Bushougoma assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. Bushougoma recommends safe practices when working with the tools or equipment seen or implied in this video. No information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not Bushougoma.





475,000 Mile Acura Legend
The latest installment in the obsession with getting this junker to half a million miles on the original drivetrain :) Still going. This is on Arizona Hwy 87 southbound near Fountain Hills, Arizona on my way home from work on 5/19/2011. I'll be back from the moon in just a couple thousand miles! Car is dirty; it rained yesterday. Audio credit: Cake.





Acura's Game-Changing TLX - Autoline After Hours 262
UP FOR DISCUSSION: - Will cheap gas wreck CAFE? - Suddenly Tesla's Elon Musk likes dealers. - Test drives... FROM HELL! SPECIAL GUEST: Mat Hargett, Vice President of Acura Development & Chief Engineer, Acura TLX - Inside the engineering of Acura's game-changing TLX All that and much more with John McElroy, Autoline.tv; Gary Vasilash, Automotive Design & Production; Michelle Krebs, AutoTrader Group. Get more video everyday at http://autoline.tv





How To Solve Honda Idle Problems - EricTheCarGuy
Visit me at: http://www.ericthecarguy.com/ Before posting questions about Honda idle problems please read this: http://www.ericthecarguy.com/forum/8-Service-and-Repair-Questions-Answered- Here/41476-solving-honda-idle-issues-hunting-idle The viewers have chosen and this weeks video will be about solving Honda idle problems. I'm really not surprised as I get a lot of questions and requests about this very subject. Here are the links I promised in the video that will help you address specific issues mentioned in the video. How To Bleed a Cooling System http://www.youtube.com/watch?v=zUpXgAJ1gjU How to Check for Vacuum Leaks http://www.youtube.com/watch?v=9CPqbaSgcok Reading Check Engine Light Codes http://www.youtube.com/watch?v=BD05sPclLyE Diagnosing an Overheat http://www.youtube.com/watch?v=hUzOTnsWImI Hopefully when your done checking all that stuff out you will have solved your Honda's idle problem, if not leave a comment or send me a message and I'll see what I can do just make sure you have tried all the stuff in the videos first as that saves me from typing so much. I also want to add my "Idle Speech" into the mix here: http://www.ericthecarguy.com/forum/8-Service-and-Repair-Questions-Answered- Here/41475-solving-honda-idle-issues-rough-idle   There are a lot of things that can contribute to an idle issue, in fact in the end it may still be there to some degree because of the nature of that engine however here are some things to start with. First start with a good tune up, use NGK or Nippon Denso plugs, don't change the wires if they are OE, if they aren't OE you might consider NGK wires as they are very good and less expensive then OE.  A quality cap and rotor should be good.  A new air filter also helps. Don't change the PCV valve, if you see an aftermarket PCV valve in there put a Honda in, believe it or not I've seen idle issues caused by aftermarket PCV valves, the OE's last just about forever so you can easily justify the expense. Next a good valve adjustment, this goes a long way to smooth out the idle if done correctly, mess it up and things can get a lot worse though. While you have the valve cover off check the timing belt tension, if you feel a lot of slack this can cause the cam to 'chunk' as it spins causing a rough idle.  If you think the belt has been on there for some time then you might consider changing it and resetting the tension properly, if it's not ready for replacement you can reset the tension to take up the slack. DO NOT adjust the idle screw under any circumstances, it is set at the factory and that is the reason it was sealed in the first place. If you find that the seal has been broken and you have a low idle and you have done all of the above then you might turn the screw out a little to see if that helps the idle but only enough to try and bring it back to where it was before it was adjusted in the first place. Last clean the screen in the Idle Air Control valve, this can get clogged up with carbon over time and cause the flow through it to be restricted which can cause idle issues. If you still have a 'rough' idle after all of this THEN look to the engine mounts as you want to be sure the engine is running correctly before you go for those as the one in the back is a real pain to replace. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





1992 acura legend fuel pump - seat removal Part 1
1992 acura legend fuel pump removal. Tools= Philips Screwdriver, 10mm Socket and extension ratchet for ALL nuts! except the 17mm socket for Big nut at the end of video. --- Disconnect Battery. Top 2 bolts under headrests, Bottom 4 bolts between seats-behind belts. Remove bottom seat- remove top back by pulling UP-- Remove cover- remove all bolts on top of gas cover- and holders (8). I point to each one at the end of the video.





2014 National Acura Legend Meet
A few scenes shot by my friend Chris at the 10th Annual NALM, located in Los Angeles, California. Many thanks to American Honda for hosting us at our kick-off event and to the NALM event planners who pulled off an amazing event. Audio Credit: The Green Children - Norwegian Dream. For more about this event, see Drive to Five. http://drivetofive.wordpress.com/2014/07/28/10th-annual-national-acura-lege nd-meet-part-2/





How to Change Coil Over Plug Spark Plugs Acura
This video shows you how to remove a spark plug off of a vehicle with a coil on plug system. There's an exta step on this type of car. You must first remove the coil which is on top of the spark plug. Click here to show thanks, and help support Fixbook: http://www.hondahowto.com/p/blog-page_25.html Click this link to Subscribe: http://www.youtube.com/subscription_center?add_user=Hondahowto1&annotation_ id=annotation_59253&feature=iv&src_vid=QSNjtNYuD18 Click here to check out the the "Car Runs on 2 cylinders" series: https://www.youtube.com/playlist?list=PLoA1-alJGwfnWZvOZtIjPnQX88q1n3GWA&fe ature=view_all I, Jordan, assume no liability for anything you choose to do to your car, before, or after watching one of my videos, including this one. All DIY repairs, or modifications, you perform to your car are made at your own risk. Sometimes, even if you've done everything the right way, you can destroy, or damage, a piece, or part. You must understand this; part of doing a repair, and/or modification is messing up sometimes. Also, if for some reason, I do give incorrect instructions, and something breaks because you followed my instructions, I still will not reimburse, or pay, in any way, for whatever cost that may be incurred due to following my wrong instructions. Don't do anything to your car unless you yourself feel comfortable, & confident in doing so. Fixbook DIY Car Repair





Dumb Things NOT To Do To Your Car
Scotty Kilmer, mechanic for the last 46 years, shows some of the dumb things he's seen people do to their cars. And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. I answer your car questions LIVE there. Just check it out at https://www.youtube.com/watch?v=VognjkYaMjg&list=UUuxpxCCevIlF-k-K5YU8XPA&f eature=c4-overview . And remember, every TUESDAY I upload a new video, so don't miss them.





Honda Acura No Start Main Relay / Fuel Pump Relay Replacement - Bundys Garage
How to Replace the Main Relay on a Honda / Acura Vehicles Covered: 1986 Acura Integra 1987 Acura Integra 1988 Acura Integra 1989 Acura Integra 1990 Acura Integra 1991 Acura Integra 1992 Acura Integra 1993 Acura Integra 1986 Acura Legend 1987 Acura Legend 1988 Acura Legend 1989 Acura Legend 1990 Acura Legend 1992 Acura Vigor 1993 Acura Vigor 1994 Acura Vigor 1988 Honda Civic 1989 Honda Civic 1990 Honda Civic 1991 Honda Civic 1988 Honda CRX 1989 Honda CRX 1990 Honda CRX 1991 Honda CRX Questions, Comments, Concerns bundysgarage@gmail.com Music by Randall Kent All Rights Reserved 2014 Bundys Garage DISCLAIMER - DISCLAIMER - DISCLAIMER Due to factors beyond the control of BundysGarage, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. BundysGarage assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. BundysGarage recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of BundysGarage, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the end user and not BundysGarage nor any of it's subsidiaries.





How To Solve An Engine Overheat Condition - EricTheCarGuy
How To Solve An Engine Overheat Condition - EricTheCarGuy http://www.ericthecarguy.com/ I actually had fun putting this one together for you since the car I was working on didn't cooperate it made it so I could show you real world problems as they happened, very cool. I think this one is pretty self explanatory so I will save a long explanation. In case you missed the link to the "Bleeding a Cooling System" here is a link for you --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How to change spark plugs on an acura integra
This guide is for the 3rd generation integras. This is a simple job and only took me 30 minutes to complete. I also show you how to change spark plug wires and a distributer cap. I hope you enjoy the video. Also, in no way am I responsible for any injury or damage caused to you or your vehicle. This guide is simple but you should still check your vehicles manual for specs torque settings etc.





Which car is faster? Which Car is Faster?




Similar 1/4 mile timeslips to browse:

1991 Acura Legend DV8ED TURBO: 12.100 @ 124.040
Christian Pascale, Engine: 3.5, Turbos: Yes Tires: M&H Dot Slicks 26x10.5x15


1991 Acura Legend LS Nitrous: 12.953 @ 107.865
Christian Pascale, Engine: 3.5 RL bottomend, Tires: M/H slicks


1994 Acura Legend gs: 13.657 @ 101.861
Eric White, Supercharger: N/A Turbos: N/A Tires: M&H slicks


1991 Acura Legend LS: 13.782 @ 99.135
Christian Pascale, Engine: 3.5 RL bottomend, Tires: M/H slicks


1994 Acura Legend L Nitrous: 14.109 @ 101.460
Joe E - Florida, Engine: 3.2 L V6 w/ CAI, Tires: G-Force KDW


1991 Acura Legend Coupe L: 14.995 @ 94.120
Edward McLaughlin,


1991 Acura Legend LS Sedan: 15.138 @ 93.387
Shawn, Engine: Stock 3.2L 24valve V6,


1990 Acura Legend legend KA5: 15.410 @ 90.880
John Bourgoin, Engine: 2.7, Tires: yokahama


1991 Acura Legend L: 15.457 @ 90.560
Nick Semperboni, Engine: stock 3.2L, Supercharger: none Turbos: none Tires: 17


1989 Acura Legend KA4: 15.510 @ 91.000
killercivic, Engine: 2.7 24v vtec 177hp, Tires: 195/60R15


1989 Acura Legend LS: 15.640 @ 95.485
Jorge, Engine: 2.7L V6, Tires: GoodYear


1989 Acura Legend LS: 15.659 @ 90.000
Walter Gayle, Engine: 2.7L V6, Tires: Yokohama AVID H4


1992 Acura Legend LS: 16.210 @ 88.200
Greg Gilbert, Tires: Goodyear 205/40/16


 


©2014 DragTimes - Disclaimer