Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

How to Program Honda Replacement Keyless Entry Car Remote Free.wmv

Visit us at http://www.carandtruckremotes.com/ Keyless Entry Remote Keyfob Programming for Honda Cars Vans and SUV's


 


More Videos...


Extract Sensor from Honda Key
If you are repairing your old, Worn-Out or broken Honda Key then you may use its existing sensor/transponder into new shell or key casing. This will not only save lot of money but you will also be not required to reprogram the key. Old transponder can be re-used directly. No re-programming required. Suitable for Honda City, Civic, Jazz, Accord, Brio, CR-V and many other Honda Cars...





Episode #166 - 2nd Gen Honda Fit Base Keyless Entry
A cheaper way to get keyless entry in your Fit Base model.





How To Pull Honda Codes Without a Scanner -EricTheCarGuy
Link to code explanations: http://www.ericthecarguy.com/hondaacura-obd-i-codes-1992-1995 Honda ABS Codes 1994-1997: http://www.ericthecarguy.com/honda-abs-codes-1994-to-1997 Honda ABS Codes 1998 and up: http://www.ericthecarguy.com/honda-abs-codes-1998-to-now Visit me at: http://www.ericthecarguy.com/ Discussion about this Video: http://www.ericthecarguy.com/component/kunena/18-The-EricTheCarGuy-Video-Fo rum/34741-Pulling-Honda-Codes-Without-a-Scanner?Itemid=0#34741 I feel like I should have made this video a while ago but the opportunity never came up. Since I had this RL in my shop that had a check engine light AND an ABS light I thought it was a perfect opportunity to put this video together. I get asked all the time about my 'special tool' and it's really nothing more than a Honda 2 pin connector with the input wires soldered together. These connectors might be harder to find than you think but if you run across a junk honda and one of these is on the harness grab it. Even if you don't have the tool a paper clip or piece of wire will do the exact same thing so don't sweat it if you don't have the tool because shorting the connector is all you need to do. I hope you find this video helpful. Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Picking the Honda Civic Ignition
This is not for illegal purposes! This is for locksport only! This is me picking the door lock and then the ignition switch to a 2002 Honda Civic. First I pick the ignition without the key near the sensor. The immobilizer check fails and the engine will not start. Then I turn the switch again with the correct key held close to the sensor to fool the electronics. You can see the security light shut off and the engine start like a charm. Music: Huey Lewis & The News - Back in Time





How to Program a Replacement Honda Keyless Entry Remote Key Fob
How to program a replacement honda keyless entry remote key fob. This procedure was performed on a Honda CRV but you can use this programming procedure to program a key fob or keyless entry remote on select Honda's including Accord, Civic, Pilot depending on the year - Hey everyone, this is the first of many videos to come. This procedure was done on a 2004 Honda CRV but will work across many other Honda vehicles. We will try and get a list of which vehicles up ASAP. Check out http://www.ekeyfobs.com for savings on replacement keyless entry remotes and transponder keys for many different vehicles. These instructions brought to you by http://www.ekeyfobs.com





Ignition Key Transponders
Ignition Key Transponders Describes the workings and applications of modern automotive key transponders. These tiny chips transmit a digital signal that's then processed by the Anti-Theft (antitheft) module. An OK signal or command is then given to the ECM and related computers to allow injection and starter activation. Learn how they work with this clear and concise video. Future videos will detail what to do to reprogram ignition keys. Each manufacturer is different and so is each procedure. *************************************************************************** ********* Amazon Printed-Books & Kindle: http://www.amazon.com/s/ref=nb_sb_noss_1?url=search-alias%3Dstripbooks&fiel d-keywords=mandy+concepcion Google Play Android APPs: https://play.google.com/store/search?q=mandy+concepcion&c=apps Amazon Video DVDs: http://www.amazon.com/s/ref=nb_sb_noss_1?url=search-alias%3Dmovies-tv&field -keywords=mandy+concepcion Barnes & Noble Nook: http://www.barnesandnoble.com/s/mandy-concepcion?keyword=mandy+concepcion&s tore=allproducts Apple iTunes iPad: http://itunes.apple.com/us/artist/mandy-concepcion/id449573393?mt=11





How to program a replacement Nissan Keyless Remote Key Fob Transmitter
How to program a replacement Nissan Keyless Entry Remote Key Fob Transmitter You can find this nissan key fob and many others at http://www.ekeyfobs.com This video will show you how to program a new key fob for select Nissan vehicles. Remote FCC ID: KBRASTU15 Part Numbers: 28268-ZB700, 28268-C991A, 28268-C991C, 28268-5Y701, 28268-5W501 This procedure should work for the following vehicles (as long as you don't have the proximity key system) 2003 Infiniti FX35 without proximity remote 2002-2003 Infiniti QX4 2004-2008 Nissan Armada without power liftgate 2002-2012 Nissan Frontier 2005-2008 Nissan Murano without proximity remote 2003-2004 Nissan Murano 2002-2005 Nissan Pathfinder 2005-2010 Nissan Quest w/o power liftgate 2004-2005 Nissan Titan 2002-2004 Nissan Xterra 2003 - 2008 NISSAN 350Z 2002 - 2006 NISSAN ALTIMA 2005 - 2011 NISSAN ARMADA 2002 - 2006 NISSAN MAXIMA 2008 - 2011 INFINIT EX35 2003 - 2009 INFINITI FX35 2003 - 2007 INFINITI FX45 2003 - 2006 INFINITI G35 2002 - 2004 INFINITI I35 2003 - 2006 INFINITI Q45 2004 - 2007 INFINITI QX56





07 civic remote program
how to program your remote.this does not do the transponder.i no longer own a civic.this was posted for 8th gen.com,you'll have to look through there for the key numbers.hope this helped someone...





Spark Plug Well Oil Leak Fix, Honda Accord - EricTheCarGuy
Spark Plug Well Oil Leak Fix, Honda Accord - EricTheCarGuy http://www.ericthecarguy.com/ I know I've promised this one for some time so here it is. If you have this problem I recommend replacing the seals in the valve cover first and then coming back to recheck for oil in the spark plug wells in about a month or so, if you find oil then I recommend performing this procedure. I can't stress enough how important it is to make sure everything is lined up correctly when you reinstall the rocker assembly, bad things can happen if you don't. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How to program a remote key for your car
Programming a key fob is easy just follow the steps and you should be all set For VW only





How To Install Replace Ignition Lock Key Cylinder Honda Accord Acura CL 94-97 1AAuto.com
http://www.1aauto.com/1A/IgnitionSwitch/Honda/Accord/1AZIS00011 1A Auto shows you how to repair, install, fix, change or replace a broken door lock cylinder. This video is applicable to Honda Accord model years 94, 95, 96, and 97, and the 1997 Acura CL model.





HOW TO PROGRAM A FORD F150 RANGER EXPLORER KEYLESS ENTRY REMOTE
THIS VIDEO SHOWS HOW TO PROGRAM YOUR LATER MODEL FORD LINCOLN MERCURY TRUCK OR SUV KEYLESS ENTRY REMOTE... HOW TO PROGRAM YOUR 1998 1999 2000 2001 2002 2003 2004 2005 2006 2007 2008 2009 FORD LINCOLN MERCURY KEYLESS ENTRY REMOTE KEY FOB PROGRAMMING INSTRUCTIONS F150 F250 F350 RANGER EXPLORER MOUNTAINEER ESCAPE EXPEDITION EXCURSION KEY FOB





Honda No Start? POSSIBLE Main Relay - EricTheCarGuy
Honda No Start? POSSIBLE Main Relay - EricTheCarGuy http://www.ericthecarguy.com/default.aspx Here is a GREAT website article about soldering these I strongly suggest you check this out before doing this repair. http://techauto.awardspace.com/mainrelay.html The first of the "Quick Tips". I think I'm going to throw one of these in from time to time to keep things lively. So if you have a Honda or Acura that is not starting DUE TO LOSS OF FUEL PRESSURE this is a good place to start. You may be able to repair the main relay normally found under the dash on the drivers side. If this helps great remember me fondly and pass my name along because I just saved you at the very least about $80, at the most $200. I will be upgrading my website very soon, in fact I will post a video when it is up. Cool new things on the horizon for ETCG and YOU the viewer. So if you want take a look at the old site because it's days are numbered. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Till next time Be Safe and Stay Dirty. Oh yea, and have fun too. ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How to install a car remote start (roughly) PART 1
This Video and the following 2 parts are just a rough overview about how to install a remote starter kit in your car. The car I am installing this in is my 3.8L fully loaded Dodge Grand Caravan. YES I DRIVE A MINIVAN and I dont have kids, so what? xD Anyway I want to show how complex this job is and that it sure aint easy. If you have knowledge as technician or electrician you will be fine, if you are COMPLETLY new to this kinda stuff, I recommend to see a dealership or a outfitter to get your remote start installed. Installing these kind of systems wrong into your car, could cause the electronics to fail. I have never done this before and received no help, so understand this is not to show you how YOU HAVE TO do it, I simply want to show you what needs doing, if you decide to install a cheapy kit. Messing with the security controller (transponder module) could prevent you from driving back home, if damaged during install. As an advice, when you program the transponder module to override the factory anti theft and you fail, DO NOT REPROGRAM right away or try to start the car by remote. Instead, insert the key and start the car until the Anti theft module is reset (let it run for 20 seconds). It WILL lock you out, if you attempt to start the car more than 4 times without having the right "disarm chip". Once the original key is inserted and the car ran, the module will be set to zero counts of fail starts and you will be fine. As for the complainers and haters. Sure there are pro installers that do a MUCH MUCH better job than I am doing here, but I bet you a million dollars, you had to learn your way also, so keep your criticism on a low and understand this was MY FIRST TIME! A so called, remote start kit virgin. Thanks :)





How to program keyless entry remote for 2003-2008 Toyota Corolla
In this video I will show you how to program a replacement keyless entry remote control for a 2005 Toyota Corolla. This should work on 2003 to 2008 Corollas. make sure you have the correct transponder model # GQ43VT14T . It is the FCC ID number but has to be same style since the same FCC ID is used for other Toyotas. 1. Start by sitting in the car with the key out of the ignition, Open drivers door. (step 2 and 3 has to be done within 5 seconds) 2. Insert the key into the ignition and Pull it out 3. Insert the key into the ignition and Pull it out Perform these steps within 40 seconds. Drivers door is still open. 3. Close drivers door and open the drivers door. 4. Close drivers door and open the drivers door. 5. Insert the key into the ignition and Pull it out 6. Close drivers door and open the drivers door. 7. Close drivers door and open the drivers door. 8. Insert the key into ignition and leave it in ignition. 9. Close the drivers door. 10. Turn the ignition to the "ON" position and then to "OFF" position. 11. Pull out the key from the ignition. ** the power door locks should lock then unlock so you are in programming mode and ready to program the remotes. If this does not happen start again. Remote programming has to be done within 40 seconds. 12 Press both the lock and unlock buttons on the remtoe for about 1 and 1/2 seconds then let go 13 Press lock button for 2 seconds and let go. The car doors should lock and unlock. If they do then you are ready to program the next remote. 14 Open drivers door to end programming mode.





Which car is faster? Which Car is Faster?




Similar 1/4 mile timeslips to browse:

1957 Chevrolet Bel Air pro mod: 6.520 @ 218.330
Bruce Micetich, Engine: 526 ci alan johnson pontiac, Supercharger: 14-71 SSI F rotor Tires: mickey thompson


1957 Chevrolet Bel Air Pro Mod: 6.750 @ 211.000
Dave Jackson, Engine: 526 AJ, Supercharger: 1471 Hi Helix Tires: 34.5


1960 Chevrolet Bel Air : 7.951 @ 182.930
Mike Casella, Engine: 707 Donavan, Tires: Hoosier


1960 Chevrolet Bel Air 2dr Sedan: 8.134 @ 169.830
Mike Casella, Engine: 707 Donavan, Tires: M/T 10.5W


1955 Chevrolet Bel Air 210: 8.183 @ 165.580
Tim Harper, Engine: 522 BBC, Supercharger: Procharger F-2 Tires: Hoosier Quick Time Pro 31X18.50


1979 Chevrolet Malibu : 8.532 @ 159.100
Todd Geisler, Engine: 582ci BBC, Tires: Hoosier DOT Drag Radial 295/65-15


1978 Chevrolet Malibu : 9.023 @ 148.970
scott lorenzen, Engine: 496 bb chevy, Tires: 17.5 x 32 et streets


1956 Chevrolet Bel Air hardtop: 9.320 @ 145.000
Berny Corscadden, Engine: Big Block, Supercharger: no Turbos: no Tires: Hoosier


1978 Chevrolet Malibu : 9.410 @ 143.000
Tug Brock, Engine: 488 BBC,


1978 Chevrolet Malibu : 9.510 @ 142.700
todd pasch, Engine: Dart 540, Tires: m/t29,5x13.5x15


2006 Mercedes-Benz SLR RENNtech: 9.687 @ 142.120
SGC, Engine: 5.5L Supercharged V8, Tires: Hoosier


1979 Chevrolet Malibu Coupe: 9.710 @ 135.000
Garrett Porter, Engine: 426 cubic inch Chevy small block, Supercharger: none Turbos: none Tires: Hoosier


1955 Chevrolet Bel Air : 9.780 @ 139.600
Doug Petroline,


1965 Chevrolet Malibu ss: 9.840 @ 139.230
MIke stevenson, Engine: chev sb 355, Tires: mickey thompson et street


1960 Chevrolet Bel Air 2 dr: 9.885 @ 133.490
Mike, Engine: 406, Tires: 33X18.5 ET Street


1978 Chevrolet Malibu : 9.903 @ 135.970
Jerry, Engine: 496, Tires: 31x13 Phoenix


1963 Chevrolet Bel Air Sedan: 9.950 @ 146.500
Matt Pereira, Engine: 283, Supercharger: None Turbos: None Tires: Front: 27 Dia by 7 wide: Rear29 dia by 10 wide


1979 Chevrolet Malibu 2 door: 9.975 @ 135.540
todd myers, Engine: 496 bbc, Tires: 28x10.5 15 mickythompson


1979 Chevrolet Malibu station wagon: 10.000 @ 115.450
jim bowling, Engine: 383 s/b chev, Supercharger: none Turbos: none Tires: m/t 29.5x9x15


1978 Chevrolet Malibu classic: 10.080 @ 130.000
dennis cantrell, Engine: 414 small block, Supercharger: no Turbos: no Tires: 14x32x15


 


©2014 DragTimes - Disclaimer