Electric Homemade Wooden Go Kart Run 3
Hey guys this is Revision 3 of the electic go kart. It has a new Ramsey
winch motor and a 400amp curtis 1204-410 motor controller. The sprockets
have been upgraded to hold a #35 chain and the new size chain has been
added. I the motor specs: 8000RPM at 24v, 32 in pounds of torque, 45 amps
no load, 140 amps full load 6 hp continuous, 11 peak, running currently at
36v 85amps. Thanks for watching. Please leave your comments in the sectiob
below. Please note: this is not supposed to be professional looking or
super-functionalal for that metter, it wat meant to be a fun project.
Electric Trike w/Air Ride Suspension Pt. 2
This is the video of the built trike and run test. Sorry for the poor video
quality. The trike worked out to be 24v.
SURVEY LINK: https://www.surveymonkey.com/s/VN26FTG
RYNO Motors Full Story
This is a great story on the early days of RYNO Motors. See our latest
creation pre-production show bike at our web-site and pre-order at
http://rynomotors.com/store and don't forget to buy a Tee Shirt:
Dual Motor Electric Vehicle Drivetrain With Powerglide 2 Speed Transmission Walkthrough by EV West
Here's a brief 10 minute video that gives a nice overview of the EV West 2
speed Powerglide transmission that runs without a torque converter direct
drive to 2 coupled Warp 11 motors. Depending on the voltage and current,
these twin motors can put out well over 1000 lb/ft of torque, and 600+ horsepower. We used
this motor and transmission combination to power our BMW M3 to the summit
of Pikes Peak in 2012 setting an all time record for street legal electric
cars. The strength and reliability of this system is key. For more
information regarding this bolt in drive train, please visit
http://evwest.com for the latest updates.
My 48 Volt Electric Motorcycle
This is an all electric motorcycle that I built in my garage in late 2008.
The first eight months were spent researching components, saving money,
planning the modifications, tearing down the original bike, and finally
purchasing all of the parts. The build was completed over a 3 day period.
Battery pack rating: 2.5 KW
Top speed: 50 MPH
Range: 25 miles
4x BB EB50-12 Batteries (50 amp-hour x 12 volts)
Alltrax 4865 Motor Controller (max amperage output set to custom limit)
Etek-R Brushed DC Electric Motor
Magura 0-5k Potentiometer Throttle
25 Amp Quickcharge Charger
70000 watt electric go-kart
Very powerfull go-kart with 400X A123 systems lithium cells, zilla Z1-K
1000amps 300volts DC controller and heavy duty forklift motor. 70 KW output
limited. 12.3 sec 1/4 mile. 160km/h top speed.
Diamondback Ebike with 500w cyclone motor part 1
Short Video showing off my newly completed Ebike conversion.
running a cyclone style midmount motor (500W 24V) i am running on a NI-Mh
battery pack @ 24V 18AH. i am also running a Cycle Analyst for instant
readouts of the electrical system. top speed so far has been 60 km/h. Range
on the current battery should be about 28km to 80% DOD (with moderate
i will have a video of the bike being ridden up shortly.
I have only been on one 13km test ride so far. 13km took 137 watt hrs (or
6.1AH) this battery is 432 watt hrs (or 18AH).
i have changed the MTB type tyres to serfas drifter semi slicks for
improved on road performance and lower rolling resistance. added a Delta
Air Zound air horn (rated at 115Db) also added a cheap etrex GPS.
The only things left for me to do are to change the rear gear set for a
Nuvinci hub, and run a LiFeP04 battery pack.
The LiFeP04 battery upgrade should happen very soon, then the true
potential of this motor should be known.
please watch parts 2 , 3 , and 4.
Electric Scooter Motor Test
Typical 250 watt Chinese made scooter motor I took off an electric scooter
that was junked. I'm testing this using a car battery charger with a
capacitor in parallel to smooth the charger output. I may eventually use
this on a homemade scooter or pocket-bike
Maker: Unite Motor Co LTD
Permanent Magnet DC
24 vdc 14amp 250 watt 2500RPMs