2005-2014 Toyota Tacoma Zone Off Road Spacer Install Video and Wheeling
See the kit, instructions and more at http://zoneoffroad.com/product?ki=355&gr=-1
Featured Vehicle: 2009 Toyota Tacoma 4wd
Lift Kit: Zone 2.5'' front spacer, 2'' rear block kit
Wheels/Tires: 33x12.50x17 MTZs on 17x9 DC-2s (will rub without trimming)
Recommended Wheels/Tires: 265/75r16 on stock or 285/75r16 on 16x8 w/ 5'' BS
Toyota Tacoma 4x4
Attempting to get up this rock and prove that this isnt a latte boy truck
Toyota Hilux and Jeep Wrangler JK offroading / 4x4
Our Day Trip to Glass House Mountains. Incl. small 4x4 recovery action at
Toyota Hilux Surf (32 Inch Maxxis Bighorn, 2 Inch Suspension Lift, Snorkel)
Jeep Wrangler JK (35 Inch BFG KM2 tyres, 2.5 inch AEV Lift, AEV Bumpers,
Genright Tyre Carrier)
Filmed with Sony Action Cam
♫ Song [Bullet Train] - Artist [Stephen Swarts & Joni Fatora]
Royalty-Free Music ツ http://freebiefm.com
♫ 'Eaten Alive' by Gaden Rhoss
Gaden Rhoss Facebook: http://facebook.com/gadenrhoss
Gaden Rhoss YouTube: http://youtube.com/gadenrhoss
Royalty-Free Music - http://youtube.com/royaltrax
Installing Wheel Spacers for Toyota 4x4 Solid Front Axle. The pros and cons of using wheel spacers.
How to install wheel spacers on a Toyota 4x4. My thoughts on using wheel
spacers, some of the pros and cons of using wheel spacers, and some of the
tricks I've learned in dealing with wheel spacers over the years.
Generally, I'm a fan of wheel spacers. The biggest thing is just to
realize that you've deviated from the factory tolerances and that parts
(like wheel bearings) are going to wear faster from strain that falls outside the
design parameters. but, if you're running tires big enough to need wheel
spacers, you probably know that already.
I say it in the video, but I can't say it enough: Check those nuts that
hold the spacer on often. Wheeling rigs have a freakish ability to loosen
everything attached to them.
Toyota Tacoma Transformation w/ 4 Wheel Parts & Fred Anderson Toyota
http://www.4WheelParts.com - Today at 4 Wheel Parts, we're transforming
this 2010 Toyota Tacoma with some basic modifications to make it a true
original. Here's what we're doing to upgrade this truck:
- 3" lift kit
- Add-a-leaf rear spring for an extra 1 1/2 to 2 inches in the rear
- Pro Comp rear shock absorbers
- Upgraded strut valved for this truck
- New front coil spring to increase spring rate
- Black grille overlay
- Side steps
- 18" KMC Rockstar Wheel
- 33" Pro Comp Xtreme All Terrain Tires
You can find all of these parts and much more for your next truck, Jeep, or
SUV ugprading project at www.4WheelParts.com.
Invisible Body Dropped Taco
THIS TRUCK IS UNDER CONSTRUCTION IN THE VIDEO!!
Chris Simonson's 2001 bagged and body-dropped Toyota Tacoma.
18 inch Niche Rhines.
Custom control arms
Chromed engine components
Fully Functional A/C
Toyota 4runner electric rear window.
Shaved everything and suicide doors.
Shot the video during teardown before paint.
Will be on the show circuit in the coming months.
"We Don't Know- D-WHY"
Toyota FJ Cruiser Tacoma Level Kit Install Video
Presented by My4x4store.com this video gives you detailed visual
instructions on how to install a front level or lift kit on a FJ cruiser.
The instructions will also work for a 2005+ Toyota Tacoma as the FJ and
Tacoma share the same front suspension.
This video is a guide for the do-it-yourselfer that is going to attempt
this in his driveway at home. No fancy hoists or lifts, no special ball
joint press, no strut compressor.. just good old fashioned driveway
This installation should take the average hands on person about 2-3 hours
to do in the driveway.
You will need a good set of metric hand tools, a hammer, a floor jack, jack
stands, a pry bar and some patience.
If you are interested in purchasing a lift or level kit for your truck or
SUV, call My4x4store today at 801-930-0091
TOYOTA TACOMA STUCK ON BEACH
This driver made the mistake of driving n to close to one of our outflows
. When you see a large stream of water on our Peninsula it is the the
rain runoff from ditches and lakes . What happens is when the tide goes
out the water will gouge out a trough in the loose sand . When the tide
comes in it will fill the edges of the trough with loose sand . While
it will look hard it is fact mostly water . It has the conistancy of
quicksand . If you walk into it you will sink maybe 8 to 10 inches . A
car or truck will sink to its frame . This occurs all along our beach
. I advise people to not cross these streams at high water and at low
water you want to go as far west as you can to cross over . This truck
was in quicksand like material 2 hours before he called me . After the
tide went out the water drained out of the sand and it was rock hard
around his truck .