When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Price: $15.00
Click Here. Double your traffic. Get Vendio Gallery - Now FREE!
VIPER KEYLESS REMOTE EZSDEI474V 4-BUTTON VERY GOOD CONDITION FACTORY REMOTE GREEN LIGHT VERY GOOD CONDITION
WILL WORK ON
VIPER SYSTEMS
THIS IS THE ACTUAL REMOTE IN PICTURE
100% TESTED AND IN VERY GOOD CONDITION
WILL WORK ON MORE MODELS JUST MATCH UP YOUR #\'S
WHY BUY A NEW ONE WHEN A USED ONE WORKS JUST AS GOOD FOR A FRACTION OF THE PRICE
FCC-EZSDEI474V
Please note:
A Valet / Programming switch is required to program this remote.
Programming can be difficult if you are not familiar with it. Please read the programming instructions (below) before purchasing. Assistance from an auto specialty shop or locksmith may be needed.
Compatible w/ the following systems:
Automate
6
7
10
25
35
410
425
435
52
53
552
553
Avital
2100
2200
2300
3100
3200
3300
4000
4100
4200
4300
4400
Maxx2
Maxx3
Hornet
533 T
554 T
740 T
742 T
851 T
Python
400 HP
440 HP
450 ESP
460 HP
500 HP
625 HF
650 ESP
660 XP
700
900
1000 HF
PC 1000 HF
1200 XP
1400 XP
1500 HF
1600 XP
2000 HF
3000 HF
3000 ESP
Sidewinder
3000 HF
3000 ESP
3200 HS
3300 HS
3500 ESP
4500 HF
5000 HF
5000 ESP
5500 XS
6000 HF
6000 ESP
6500 HF
6500 ESP
7000 HF
7000 ESP
PC 7000 SHF
Rattler
100
110 D
200
210 D
250
259 R
300
310 D
359 R
369 D
Valet
450 R
519 H
551 R
552 T
562 T
561 R
712 T
716 T
Merlin
2000
Ungo
K10
K20
RK1
RS10
S100
S400
S660
S670
SR1000
SR5000
SR6000
Viper
100 HF (ESP)
130 HV
150 ESP
160 XV
210 HV
211 HV
300 HF
PC 300 HF (ESP)
300+ HF
330 V
350 HV
500 HF
PC 500 HF (ESP)
550 HF
550 HF (ESP)
560 XV
571 XV
600 HF
PC 600 HF (ESP)
650 XV
671 XV
700 ESP
771 XV
PC 800 SHF
800 SHF ESP
850 XV
1000
1002
3000
3002
5000
5002
7900
Programming Instructions:
The vehicle’s system can store up to 4 transmitters (remotes) into memory. Use the following programming routine to add transmitters to the vehicle’s security system or to change button assignments if desired.
In order to enter Learn Routine, the Valet/Program push button must be plugged into the main brain\'s Blue 2 Pin Port (Look for a small black push button located under the drivers dash or drivers kick panel somewhere).
The Valet/Program switch, plugged into the blue port, is used for programming. There is a basic sequence of steps to remember whenever programming this unit.
1)Open a door and make sure the dome light is on.
2)Turn the ignition on to the RUN position or you may also start car.
3)Within 10 seconds, press and release the Valet/Program switch the number of times that corresponds to the desired channel (listed below). Once you have selected the channel, press the switch once more and HOLD it. The LED will flash and then the horn will chirp (if connected) to confirm the selected channel. Do not release the Valet/Program switch.
CHANNEL #
FUNCTION
1
Arm / Disarm / Panic
2
Silent Mode / Remote Valet / Trunk Release
3
Remote Start or other accessories
4
Arm only (4 button remote)
5
Disarm only (4 button remote)
6
Panic only (4 button remote)
7
Auto Program single Arm – Disarm – Panicbutton configuration (4 button remote)
8
Auto Program this remote
9
Delete all transmitters
CHANNEL 9:
If any transmitter button from a known transmitter is programmed to channel 9, all transmitters will be erased from memory. This is useful in cases when one of the customer’s transmitters is lost or stolen. This will erase any lost or stolen transmitters from your system’s memory. It can also be used to start from scratch if the transmitter buttons were programmed incorrectly.
4)You can advance from programming one channel to another by releasing the Valet/Programming switch and tapping it to advance channels and then HOLDING it. For instance; you have programmed Channel 1 and you want to program Channel 2. Release the Valet/Program switch. Press it one time and release it to advance from Channel 1 to Channel 2. Now, press and HOLD the Valet/Program switch. The LED will flash 2 times and the horn will chirp twice (if connected). As before, do not release.
If you want to program Channel 3 after programming Channel 1, release the Valet/Program switch, press it twice and release it to advance to Channel 3. Then press it once more and HOLD it. The horn will chirp 3 times (if connected) and the LED will flash 3 times to confirm it is ready to receive the code from the transmitter.
5)Once the code(s) are learned, the Valet/Program push button can be released.
6)Programming mode will be exited if one of the following actions occurs:
a.Ignition key is turned to the OFF position
b.Valet/Program switch is pressed too many times.
c.More than 15 seconds elapses between programming steps.
The horn will emit one long chirp when programming mode has been exited.