When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Price: $2203.95
Item#:CXR-TRB-KIT-SBC-TT-CHEVELLE-GT35-NO-IC
You Are Bidding One Brand New
CXRacing Twin Turbo Kit (without Intercooler Kit) For 1963-1967 Chevrolet Chevelle with Small Block SBC Motor (SBC 265 283 302 305 307 327 350 400 Etc)
This Kit Is Developed on a Chevelle Chassis, Should Also Fit Many Old Muscle Car A-Body Chassis: Chevelle, Malibu, El Camino, Impala, Bel Air, Camaro, and Nova, But Small Modification Might Be Needed.
Headers, Turbos, Downpipes Designed and Built to Fit Stock Chassis, No Cut. See Installed Pictures.
Application:
Chassis: 1963-1967 Chevrolet Chevelle
Motor: Small Block Motor, Both Carbureted and Fuel Injection (Just Need to Run Different Intercooler Piping).
Note:
1. This Kit is for Turbo Kit Hardware Only. Dual Turbo Comes with the Kit Supports 900-1000 WHP. However, You Must Have a Built Motor, Upgraded Fuel System, Tune the System, and Stronger Transmission and Rear End to Support Bigger Power.
2. Need to Drill Two Oil Return Ports on the Oil Pan for Turbo Oil Return, and Weld Two AN10 Fitting (Make Sure to Clear Crank Clearance Inside the Oil Pan When Welding the Fitting). Turbo Oil Feeds Run From the Back of the Motor, Spilt to Two Oil Feeds.
Product Being Sold:
Twin Turbo + Header + Downpipe + Wastegate + WG Dump Tube + Oil Line Kit
This is CXRacing\'s Newest Products for the Application Stated Above. All Parts Are Developed from Ground Up in Our R&D Center in USA, Designed and Built for Improved Performance Gains, with Excellent Fitment and Easy Installation.
Product Info and Spec:
-
Turbo and Wastegate:
Dual T4 GT35 Turbo, Supports 900-1000 WHP Combined
4\" Air Inlet, 2.5\" Compressed Air Outlet
3\" Vband Exhaust Outlet
Journal Bearing
Oil Cooled
.70 A/R Compressor , .68 A/R Turbine
44mm Wastegate 8 PSI -
Header:
1.65\" Runner
Curves Outward with T4-Vband Elbows, Fits A-Body Chassis -
Downpipe:
3\" Stainless Downpipe
Ends At the Transmission Bell Housing Area, You Can Make Your Own Exhaust System
Notes:
-
Off Road or Track Use ONLY, NOT for Street Use.
-
Due to the Complexity of Swapping a Motor to Different Chassis, Please Make Sure that You Understand the Application Stated Here are the Right Parts for Your Project.
-
Parts Being Sold are the Kit Being Advertised ONLY. Other Parts Shown on Pictures are for Demo Only (of Our Complete Swap Kit). Check Our Other eBay Listings.
-
Intercooler Kit Is NOT Included. We Offer It Separately, Please Check Our Other eBay Listings.
Click Below Picture to Watch Installed and Running Video
Especially Designed, Made for the Application Stated
Fully Tested, Simple Easy Installation
Offers Excellent Performance Gains
One of the Best Kits on the Market, with High Quality Products and Affordable Pricing
T4 GT35 Turbo x2 44mm Wastegate x2
Header with Turbo Elbow x One Pair
Downpipe x 7 Pcs WG Dump Tube X 4 pcs Vband Clamps x 11 pcs
Note: Below Flowing Pictures Show A Fuel Injection Setup, This Turbo Kit Supports Both Carbureted and Fuel Injector Motor. Just Need to Run Different Intercooler Piping Setup.
Note: Below Installed Pictures Show Carbureted Setup.
Turbo Oil Feeds Run from the Back of the Motor (where the long screwdriver points at).
Note: Driver Side Downpipe is Slightly Lower than the Passenger Side, Because Some SBC Motors Use Large Oil Filter, The Driver Side DP Runs Around it. But It Is Still Leveled with the Frame.
We sell most of our products internationally.
Shipping cost outside US continental States is Higher, Please Refer to the following Table for Extra Costs.
Destination Shipping Method ETA Cost PR, Guam, VI, AK ,APO,HI USPS or Fedex $415 Canada USPS or Fedex $435 Other Countries USPS or Fedex $685