When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Price: $49.95
1991-1998 Volvo 740 760 940 960 S90 V90 Driveshaft Center Support Bearing 183265 1991-1998 Volvo 740 760 940 960 S90 V90 Driveshaft Center Support Bearing 183265
Volvo Driveshaft Center Support Bearing - Complete replacement bearing
Please confirm measurements of the original bearing with the sizes provided below.
Internal Diameter: 45mm (1.771")
Width: 16mm (0.629")
Hole Centers: 80mm (3.149")
1992-1993 Volvo S90
1997-1998 Volvo V90
1991-1992 Volvo 960
1991-1998 Volvo 940 2.3l Fuel Injected
1991-1992 Volvo 940 2.3l Fuel Injected Turbo
1991-1993 Volvo 940 SE 2.3l Fuel Injected Turbo
1991-1997 Volvo 960 2.3l Fuel Injected Turbo
1992 Volvo 960 3.0l 6 cylinder Fuel Injected
1992-1993 Volvo 960 3.0l 6 cylinder Fuel Injected 4DRS S.R
1991-1993 Volvo 960 3.0l 6 cylinder Fuel Injected 4DRS W/O S.R
1992-1993 Volvo 960 3.0l 6 cylinder Fuel Injected 4DRS W/O Sunroof
1992-1993 Volvo 960 3.0l 6 cylinder Fuel Injected 4DRS with Sunroof
1992-1993 Volvo 960 4DRS S.R
1991-1993 Volvo 960 4DRS W/O S.R
1991-1997 Volvo 960 4DRS W/O Sunroof
1992-1997 Volvo 960 4DRS with Sunroof
bearing OE: 1340501 +183265,
Features:
- Brand new center bearing
- 1 year warranty
- OE Spec
- ISO 9001 Quality control
- Fast US continental shipping
- No hassle returns
Welcome to Mako Driveshafts LLC
We are excited to have you as our customers
Our business is built around finding solutions for our customers and we appreciate every one of you!
We are a proudly USA built company and we ship out of Fort Lauderdale, Florida
Whatever we have shown in stock is on the shelf and ready to ship
We offer same day shipping and if purchased before 1pm EST consider your order on the way!
Step 1
Establish what style of Universal Joint you are working with. This is important, since u-joints have a different way of measuring depending on the style of u-joint that you have. The way that you measure the u-joint will translate into how you measure the other components you may need. ALWAYS use a set of Vernier Calipers or Micrometers, tape measures will never produce accurate results! These are mechanical parts and require precision
After comparing the Type of U-Joint in Step 1)
Measure your u-joint in the correct manner and identify what series you have
Outside Snap Rings *Inside Snap Rings **Outside+Inside Snap Rings *** SPRTAB Style **** Bearing Plate *****
Light & Medium Vehicles
Outside Snap Rings *Inside Snap Rings **Outside+Inside Snap Rings *** SPRTAB Style **** Bearing Plate *****
Commercial Vehicles
There are two applications for slip yokes that determines what type of slip yoke you need
- Transmission slip yokes that slide onto the output shaft of your transmission
- Driveshaft slip yokes that allow for the shaft to move in and out during operation
Please follow the steps
- Establish the type of universal joint
- Measure and determine the series of your universal joint
- Determine if you need a transmission or driveshaft slip yoke type
- Count the splines and take note for missing splines. If you count 15 with a gap = 15/16
- OD, the outside diameter of the splined tube
- Major diameter which is used to ensure that the slip yoke and spline fit correctly
There are two types of splines
- Determine if you need a regular stub shaft or a spline to be used with a center or carrier bearing
- Determine the tube you are going to weld the butt end of the spline into (Outside diameter & Wall thickness)
- As a general rule, the (K) measurement of the spline should be about the length (CL) of the slip yoke
- Make sure that the spline major diameter & number of splined teeth matches that of your slip yoke
Midship stub shaft (For use with Carrier Bearings)
Center Bearing's are easy!
They are used to support two piece driveshafts & are identified as follows:
- Compare the shape of the center bearing, do the brackets and general look of the bearing match?
- Take a measurement from the centerline of one mounting hole to the other to establish the length
- Ensure the inner diameter of our bearing matches the diameter of the spline its going onto
Identify your Flange
- First determine the type and series of the universal joint
- Take the measurement from the centerline of one bolt hole to the other on both sides of the flange
- Confirm the flange pilot diameter
- Are the bolt holes drilled or threaded?
Weld in Tube Yokes
- First determine the type and series of your universal joint
- Determine the outer diameter and wall thickness of your driveshaft tubing
- Beware of what material you are working with, aluminum tubing uses aluminum tube yokes