Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

Dodge Automatic Transmission Removal

Dodge neon automatic transmission replacement


 


More Videos...


How To Replace a Front Wheel Drive Axle - EricTheCarGuy
If you start to notice your FWD vehicle clicking when you make a tight turn, you might have an issue with the outer CV joint. If you make a right turn, it's usually the left side that's bad and vice versa. Most axles are easy to replace and the one depicted in this video is fairly typical of what you run into. The main differences come in with how the lower ball joint is attached. I think this part will give you the most trouble. I often get asked about what to torque the axle nut to. To be hones, I don't know. I've only ever run them down with my impact. I've never had an issue doing it that way and I don't think you would either. Just be sure to stake the nut or install the cotter pin and retaining clip if it has one. If you'd like more information on how to deal with suspension noises, check out this article I wrote on the topic. http://www.ericthecarguy.com/faq/diagnosing-noises-in-your-car Video on CV boot replacement: http://www.youtube.com/watch?v=-S-ofMoWsr0 The best place for answers to your automotive questions: http://www.ericthecarguy.com Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts Twitter: https://twitter.com/EricTheCarGuy Google+: https://plus.google.com/100195180196698058780/posts Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content Stay Dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How To Remove A Transmission: The REdneck Way (Rasslin' er down)
Removing the transmission on a 1999 Ford Ranger pickup truck 2WD. This is a quick and dirty manual transmission drop.





Torque Converters Explained -EricTheCarGuy
Visit me at: http://www.ericthecarguy.com/ In this video I cover the purpose and operation of the turbine, stator, impeller, and torque converter clutch. I hope the explanation and practical give you some insight into how these parts work to not only transfer power from the engine to the transmission, but also how it drives the transmission pump and doubles the torque output of the engine when you take off from a dead stop. I've wanted to make this video for some time. In fact I've had the fans sitting in the back of the shop for almost a year. Now that I have the Automatic Transmission Dissection video under my belt I thought I would add a torque converter dissection into the mix. I hope you enjoy this video and that it gets you a better understanding of torque converter operation. Especially since I killed my air compressor cutting this one in half. Link to compressor repair video: https://www.youtube.com/watch?v=7Zz9SKSHxFg Yes this is indeed 'take 2' of this video. I changed a few things to make the information more accurate. I am going to be posting the old video for Premium Members at EricTheCarGuy.com just for fun. Here's a link to more information about becoming a Premium Member. https://www.ericthecarguy.com/premium-content-streaming-etcg-content Other useful links Automatic Transmission Dissection (Part 1): http://www.youtube.com/watch?v=JGbsgpp2YJQ&feature=youtu.be Automatic Transmission Dissection (Part 2): https://www.youtube.com/watch?v=0Qf6O0oAs7U&feature=youtu.be Discussion about this video: https://www.ericthecarguy.com/kunena/18-The-EricTheCarGuy-Video-Forum/43707 -torque-converters-explained Why I Pulled the first video: http://www.youtube.com/watch?v=Oi5ujV1bjL8&feature=youtu.be Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How to remove an automatic transmission 00-06 Sentra Nissan
REINSTALL transmission video: https://www.youtube.com/watch?v=wDQ7B5ufjkY The auto trans stopped working with an accidental neutral drop! (accidentally moved lever to N while taking off on a green light. Then pushed back to D while the engine was revving.) This BROKE SOMETHING! SO HERE IT IS: This is how to remove the transmission off a 00-06 Sentra 1.8l





Automatic transmission (rebuilding)





The Basic Parts of an Automatic Transmission (Part 1)
Visit me at: http://www.ericthecarguy.com/ This is part one of my front wheel drive (FWD) automatic transmission dissection video. In this video I cover the operation of clutches, bands, accumulators, clutch drums, the oil pump, the valve body, valves, check balls, seals and 'o' rings, as well as the construction and function of many of the internal hard parts of an automatic transmission. To be honest a rear wheel drive transmission isn't much different as many of the basic components are the same. I guess what I'm saying is that you could use the information in this video to have a basic understanding of a rear wheel drive automatic transmission also. It is just a basic overview of the main components. I don't get into theory and operation so much. Just the general operation and identification of the parts. I may make more videos on this topic based on the comments I get so feel free to ask questions and perhaps I'll answer them in a future video on this topic. There will also be a separate video on the parts and operation of the torque converter as well. When that is posted I'll post links below to that video. Part 2: https://www.youtube.com/watch?v=0Qf6O0oAs7U Torque converter dissection: http://www.youtube.com/watch?v=_U_d_tBn-HQ Discussion about this video: https://www.ericthecarguy.com/kunena/18-The-EricTheCarGuy-Video-Forum/43585 -the-basic-parts-of-an-automatic-transmission#50371 Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How to install Torque Converter and Automatic Transmission
Family owned and operated for over 40 years with over 75,000 satisfied customers. Rated #1 Click on blue link http://www.enginefactory.com/letters.htm This video shows the proper way to install a torque converter and install an Automatic Transmission. Produced by enginefactory.com Home of the most complete Live Run Turn Key Crate Engines. Chevy and Ford Performance engine. All engines are live ran and are Ready to Run out of the Crate. Building Muscle Car Engines Since 1969





Fixing A Transmission That Slips And Clunks
Scotty Kilmer, mechanic for the last 46 years, shows how you can fix your own automatic transmission. If it's slipping or clunking, check out this video. And, If you like my car help, be sure to watch my live car talk show every Saturday morning at 10 AM CST on YouTube. I answer your car questions LIVE there. Just check it out at https://www.youtube.com/watch?v=VognjkYaMjg&list=UUuxpxCCevIlF-k-K5YU8XPA&f eature=c4-overview . And remember, every TUESDAY I upload a new video, so don't miss them.





Automatic transmission Part 1
I was just trying to show peopel who want to know about automatic transmissions and transaxles. I am not an expert and i just try to share the video with you guys. Thanks for watching





GM 4L60-E Transmission Re-Assembly (Rebuild) - Transmission Repair
On this video we go through the re assembly of a 4L60E Transmission. I tried to make this video shorter for you so I skipped the bushing installation and installing the bolts on the valve body. But you can go to the teardown video for reference on where each bolt goes, since they're different sizes. I will make a follow up video on bushing installation.





How to Install an Automatic Transmission
How to Install an Automatic Transmission http://www.hdautomatics.com/ http://www.txchange.com/ http://www.onlinetransmissionparts.com/





Trans & Clutch 1 - Remove Transmission
This is the first in a multi-video series regarding clutch tech. The clutch itself is a simple mechanism, but it's buried deep in the engine, so you can't just cover the clutch. First, you have to cover how to remove the transmission to get to it. This project started off strange, got kind-of not-good, and then took a turn for the worst. The typical clutch job is not as difficult as the next video will display, but it's good this happened to me because I film this kind of crap. If for some asinine reason you encounter the kind of failure I experienced, you'll know what to do after the next video. Clutch assembly will be covered in a third video. About the car: You saw the other assembly video. You know when I put this thing together. You know it doesn't come out to play when it's cloudy. I've had it on the road less than an earl change. Freshly rebuilt TRE Stage 2.5 trans with a brand new ACT 2600 and a sprung 6-puck (MB1-XTG6) on a stock flywheel. This is Transmission #4.





Cambio de aceite de transmision automatica GM (version completa)
Video de cambio de aceite de transmision automatica de un buick lesabre 3.8 mostrando todos los detalles paso x paso y sin prisas.





How To Install Replace Transmission Transfer case Tailshaft Seal 1AAuto.com
http://www.1aauto.com In this video 1A Auto shows you how to replace, remove, and install the transmission transfer case tailshaft on an 89 GMC Jimmy. This video is applicable to the GMC Jimmy and Chevy Blazer, model years 83, 84, 85, 86, 87, 88, 89, 90, and 91.





Ford Ranger Transmission Removal - Quick And Easy
How to remove the transmission on a 1999 Ford Ranger. This is a 5 speed manual with 2WD. 2.5 liter 4 cylinder engine. This procedure took about an hour.





Which car is faster? Which Car is Faster?




Similar 1/4 mile timeslips to browse:

1994 Volkswagen Gol saveiro: 8.380 @ 180.000
Javier Di Maio, Engine: 2.0, Turbos: gtx47r


2001 Dodge Ram 2500 SLT Diesel 4x4: 10.430 @ 130.600
Karl Mireiter, Engine: 6.7 cummins, Turbos: Single 480


2005 Dodge Ram 2500 : 10.750 @ 126.650
david v, Engine: 5.9 cummins, Turbos: ed s469 Tires: 305/50r20


1997 Dodge Ram 2500 Diesel: 10.905 @ 120.460
Jesse Bradley, Engine: Cummins, Turbos: Twin- 66/74top 86/96 bottom Tires: toyo proxes s/t's


2006 Dodge Ram 2500 SLT Regular Cap 4X4: 11.247 @ 121.800
Allan Cook, Engine: Cummins, Turbos: Aurora 5000 Tires: Hankook


1995 Dodge Ram 2500 SLT: 11.770 @ 104.000
Michael, Engine: Cummins 360, Turbos: HRD Twin Turbos (HX-35/????) Tires: MT slicks


2006 Dodge Ram 2500 SLT: 11.972 @ 114.780
Allan Cook, Engine: 358CI Cummins Turbo Diesel, Turbos: HY9 on top of a S400 Tires: Stock


1994 Dodge Ram 2500 : 11.976 @ 112.520
Steve Long, Engine: 12V Cummins, Turbos: Single HT Turbo Tires: M&H Drag Slicks


1997 Dodge Ram 2500 Cummins Diesel: 12.112 @ 111.160
Brett Lujan, Engine: Cummins, Turbos: S300 66/71/.80


2007 Dodge Ram 2500 SLT QC 4x4 Cummins: 12.164 @ 109.940
Thomas Turner, Engine: 5.9 Cummins, Supercharger: NA Turbos: Single HTT 71mm Tires: Mickey Thompson Baja ATZ


1999 Dodge Ram 2500 SLT: 12.190 @ 109.190
Mike Dolan (Buck's Comm. Racing), Engine: 5.9 Cummins, Turbos: Twins Tires: 255/60R17


2000 Volkswagen Gol 8v special: 12.212 @ 117.844
Paulo Goncalves, Engine: ap-1.8, Turbos: neuspeed turbo kit Tires: nitto streetdrag


2006 Dodge Ram 2500 Cummins: 12.289 @ 110.500
Allan Cook, Engine: Cummins, Turbos: Twins:HY/B2 Tires: 35


2005 Dodge Ram 2500 : 12.517 @ 110.100
Eugene N, Engine: 5.9, Turbos: HTT Tires: Terra Graplers 305x50


1991 Dodge Ram 2500 LE: 12.560 @ 106.400
justin, Engine: 5.9L 1st gen cummins, Supercharger: N/A Turbos: HE351VE Tires: 315/60-15 ET Street Radial


2007 Dodge Ram 2500 QCSB: 12.600 @ 106.200
Dion Analitis, Engine: 5.9L Cummins HPCR Djesel, Turbos: Single HTT 66/71/14 Tires: 35x12.5x17 Mud Terrains


1999 Dodge Ram 2500 SLT: 12.840 @ 102.300
Mike Coleman, Engine: 5.9 Cummins, Turbos: High Tech Sledpuller 66


2000 Dodge Ram 2500 cummins diesel: 12.890 @ 102.500
james D, Engine: cummins, Turbos: BD-twins Tires: 305/70rr/16


2008 Dodge Ram 2500 : 12.964 @ 108.420
Reece, Engine: 6.7 CTD, Turbos: Silver 66 Tires: 305/45/r18 Nitto 555R


2002 Dodge Ram 2500 SLT: 13.007 @ 104.000
Tommy Terry, Engine: ARP 12 mm head studs, Supercharger: n/a Turbos: Industrial Injection Super PhatShaft 62 Tires: 265/75 R16


 


©2014 DragTimes - Disclaimer