Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

2000 Honda Civic Si 1.6L Clutch Install

This video is a 2000 Honda Civic Si 1.6L clutch installation with Gary Croyle. The clutch set used was a part number MU70137-1 (Brute# 92329). It was installed for free, no charge of any kind to the owner for video training purposes. --------------------------- The clutch diameter and dimensions are as follows: 8-5/8" Diameter x 24 Teeth x 1-1/32" Hub ---------------- This clutch set fits the following vehicles: ACURA INTEGRA GSR L4 1.8L GAS N 1997-01 HONDA CIVIC DEL SOL VTEC L4 1.6L GAS N 1994-95 CIVIC SI L4 1.6L GAS N 1999-00 CR-V EX L4 2.0L GAS N 1998-01 CR-V LX L4 2.0L GAS N 1997-01 CR-V SE L4 2.0L GAS N 2000-01


 


More Videos...


2002 Ford Focus Clutch Replacement Video (Part 2) - EricTheCarGuy
Here is a link to the full video http://www.ericthecarguy.com/vmanuals/22-vmanual-store/71-2002-ford-focus-c lutch-replacement-vmanual Part 3: https://www.youtube.com/watch?v=rvuIFAWeFSQ Well here is the second installment in the Focus clutch replacement video and we get a little farther in the process so sit back and enjoy watching me get dirty. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/ Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How To Replace a Front Wheel Drive Axle - EricTheCarGuy
If you start to notice your FWD vehicle clicking when you make a tight turn, you might have an issue with the outer CV joint. If you make a right turn, it's usually the left side that's bad and vice versa. Most axles are easy to replace and the one depicted in this video is fairly typical of what you run into. The main differences come in with how the lower ball joint is attached. I think this part will give you the most trouble. I often get asked about what to torque the axle nut to. To be hones, I don't know. I've only ever run them down with my impact. I've never had an issue doing it that way and I don't think you would either. Just be sure to stake the nut or install the cotter pin and retaining clip if it has one. If you'd like more information on how to deal with suspension noises, check out this article I wrote on the topic. http://www.ericthecarguy.com/faq/diagnosing-noises-in-your-car Video on CV boot replacement: http://www.youtube.com/watch?v=-S-ofMoWsr0 The best place for answers to your automotive questions: http://www.ericthecarguy.com Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts Twitter: https://twitter.com/EricTheCarGuy Google+: https://plus.google.com/100195180196698058780/posts Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content Stay Dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How to Change Tie Rods (inner and outer tie rod ends)
How to replace inner and outer tie rods, How to replace tie rod ends, How to replace tie rods. How to check to see if your tie rod is bad: https://www.youtube.com/watch?v=brI2feYiEi8 Tie Rod End Cutaway: https://www.youtube.com/watch?v=3RjhtVse6jE Find an inexpensive tie rod here: http://www.amazon.com/s/?_encoding=UTF8&camp=1789&creative=390957&field-key words=tie%20rod&linkCode=ur2&tag=chri0e2-20&url=search-alias%3Daps&linkId=U ETDGY3TB3DUQ73O This video will show you in depth how to change the inner and outer tie rods of your car or truck. You need a special tool, an inner tie rod end tool, to complete the job (this can be rented for free at your local parts store). The job straight forward and anyone with basic tools can do it! **If the video helped, please give it a "thumbs up" and consider subscribing. Leave any questions or comments below and I will answer them as well.** Follow me on Facebook: https://www.facebook.com/chrisfix8 Follow me on Twitter: https://twitter.com/ChrisFixed Subscribe: http://www.youtube.com/subscription_center?add_user=paintballoo7 How to replace Drum Brakes: https://www.youtube.com/watch?v=3FYRwfKNHxw How to replace Differential Fluid: https://www.youtube.com/watch?v=KmqMUJb-E4M How to fix a Squeaky Belt: https://www.youtube.com/watch?v=UF3W-vHPYHg How to replace a Wheel Bearing: https://www.youtube.com/watch?v=BPs-QALECqs Replacing a Rack & Pinion Type Inner Tie Rod DIY, How to change a tie rod on your vehicle, tie rod replacement, tie rod end replacement, tie rod end check, tie rod noise, tie rod end removal, tie rod end, tie rod removal, tie rod adjustment, tie rod, fix tie rod, tie rods, tie rod ends, inner tie rod, outer tie rod, tierod, toyota camry alignment, tj death wobble, yukun tie rod, u-joint replacement, ball joint separator, bellows boot, steering rack boot, camry tie rod, k30 tie rod, steering parts, alignment wheel, wheel alignment, satrun tie rod, saturn tie rod, tierod adjustment, tie rod adjustment, tie-rod, separate tie rod, tie rod separator, tie rod adjuster, Disclaimer: Due to factors beyond the control of ChrisFix, it cannot guarantee against unauthorized modifications of this information, or improper use of this information. ChrisFix assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. ChrisFix recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video. Due to factors beyond the control of ChrisFix, no information contained in this video shall create any express or implied warranty or guarantee of any particular result. Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not ChrisFix.





Trans & Clutch 4 - Installing The Clutch
What you wanted to know about clutches but were afraid to ask. I'm putting a ACT MB1-XTSS on the car in this video. Step height, clutch dowell pins, bolt part numbers, alignment and various clutch parts are described in this video. It's part of an all-inclusive drivetrain tech piece I'm working on that's broken up into sections to maintain focus on the individual processes involved.





How to Diagnose A Bad Clutch - EricTheCarGuy
Link to clutch replacement video for this car. http://www.ericthecarguy.com/vmanuals/vm/2002-ford-focus-clutch-replacement -vmanual Visit me at: http://www.ericthecarguy.com This one will end up being part of a larger series of videos about clutches and their diagnosis and replacement, I'm even going to post a video on 'How To Drive A Stick Shift' as part of this series. So in this installment I cover the basic steps in determining if you NEED a clutch or not. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





ZF Services Self Adjusting Clutch Fitting Procedure
AUTOiNFORM http://www.autoinform.co.uk is a FREE bi-monthly, online publication that offers the automotive aftermarket a fresh, exciting new platform using high quality video and interactive page layouts. This clip demonstrates the use of the correct tools for fitting self adjusting type clutches.





HOW A CLUTCH WORKS
HOW DOES A AUTOMOTIVE CLUTCH WORKS





Learn How A Clutch Works In Less Than 5 Minutes - EricTheCarGuy
Learn How A Clutch Works In Less Than 5 Minutes - EricTheCarGuy http://www.ericthecarguy.com/ This one is actually part of a series on clutches so be sure to check out the Integra full length clutch video as well as Adjust A Cable Operated Clutch. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Installing Front Disc Brakes - AutoZone Car Care
http://www.autozone.com/autozone/brakeJob/brakeJob.jsp In the second installment of the AutoZone Complete Car Care - Brake Job Series, Bruce Bonebrake shows you how to inspect your disc brake system. Learn how to replace brake pads and brake rotors in this step-by-step video. Get everything you need to do the job right at http://www.autozone.com





How to Change Clutch Honda Civic 96-00 (Full)
This is a video, the full version, in which I show you how to remove your transmission, and replace your clutch disc, flywheel, and pressure plate. This video applies to any Honda with a d-series engine and hydraulic clutch. Click here to show thanks, and help support Fixbook: http://www.hondahowto.com/p/blog-page_25.html Click this link to Subscribe: http://www.youtube.com/subscription_center?add_user=Hondahowto1&annotation_ id=annotation_59253&feature=iv&src_vid=QSNjtNYuD18 Click here to check out the the "Car Runs on 2 cylinders" series: https://www.youtube.com/playlist?list=PLoA1-alJGwfnWZvOZtIjPnQX88q1n3GWA&fe ature=view_all I, Jordan, assume no liability for anything you choose to do to your car, before, or after watching one of my videos, including this one. All DIY repairs, or modifications, you perform to your car are made at your own risk. Sometimes, even if you've done everything the right way, you can destroy, or damage, a piece, or part. You must understand this; part of doing a repair, and/or modification is messing up sometimes. Also, if for some reason, I do give incorrect instructions, and something breaks because you followed my instructions, I still will not reimburse, or pay, in any way, for whatever cost that may be incurred due to following my wrong instructions. Don't do anything to your car unless you yourself feel comfortable, & confident in doing so. Fixbook DIY Car Repair





Como funcionan los embragues
Funcionamiento de los embragues en un vehículo





How To Replace Clutch Hydraulics (Honda Civic) - EricTheCarGuy
How To Replace Clutch Hydraulics (Honda Civic) - EricTheCarGuy http://www.ericthecarguy.com/ I'm glad to have made this video as it was requested a couple of times. I hope to make a video just on bleeding at some point as that is probably the hardest part of the operation and there are a couple of ways to go about it. For now enjoy this one. Comments are welcome. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





1998 Honda Civic Engine Part 1 - EricTheCarGuy
Link to full version of this video: http://www.ericthecarguy.com/vmanuals/22-vmanual-store/149-1998-honda-civic -16l-engine-replacement-vmanual Link to part 2: http://www.youtube.com/watch?v=U_HQUCIXD90 Visit me at: http://www.ericthecarguy.com/ Well here it is the first of the Civic engine series, I hope you like these as they are a little 'lighter' than those trucks I've been working on lately. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG





Removal and Servicing of Clutch Master Cylinder to Slave Cylinder Connections
This video demonstrates the proper techniques for disconnecting and connecting the clutch hydraulic line at the concentric slave cylinder. These procedures apply to clutch hydraulics on various vehicles from the Ford, GM, Chevrolet and Dodge families. (Presented by Gary Croyle of Perfection) If you need help bleeding a clutch hydraulic system on a Ford Ranger or Mazda B Series pickup please refer to the following video: http://www.youtube.com/watch?v=HgNTDGwcjZc ------ www.perfectionusa.com Perfection Technical Hotline: 1-800-258-8312 then dial 4





AC Clutch Repair and Noise Diagnosis -EricTheCarGuy
This one starts out as a noise diagnosis that ends up working in an AC clutch repair on a 1998 Acura 3.2 TL. In addition to the AC compressor clutch, we also talk about repairing the AC belt idler pulley and other possible noises during AC operation. So if you ever need to replace an AC compressor clutch or have a noise coming from the idler pulley on your AC system, this video is for you. Here's some useful links. Snap Ring Pliers: http://www.jbtoolsales.com/kastar-1435-snap-ring-pliers/#oid=1002_1 The Basic Principals of AC: http://www.youtube.com/watch?v=w17DpGCcRj8 AC Performance Testing: http://www.youtube.com/watch?v=XU_A4wNuHXI Finding and Repairing AC Leaks: http://www.youtube.com/watch?v=95RdGLFIbL8 Recharging an AC System: http://www.youtube.com/watch?v=lglPJuBXVeE Discussion about this video: http://www.ericthecarguy.com/kunena/18-The-EricTheCarGuy-Video-Forum/47966- ac-compressor-clutch-and-noise-repair#78241 The best place for answers to your automotive questions: http://www.ericthecarguy.com Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts Twitter: https://twitter.com/EricTheCarGuy Google+: https://plus.google.com/100195180196698058780/posts Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content Stay Dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Which car is faster? Which Car is Faster?




Similar 1/4 mile timeslips to browse:

2003 Honda Civic EX coupe: 6.525 @ 213.500
stephan papadakis, Engine: acura nsx, Turbos: twin 64mm Tires: toyo


1995 Honda Civic DX: 8.192 @ 174.080
Kenny Tran - Jotech, Engine: 1.8 Liter, Turbos: Garrett GT4202 Tires: M/T


2000 Honda Civic SI: 8.411 @ 175.320
Stephanie Eggum, Engine: B18C1, Turbos: GT42R 74mm Tires: Mickey Thompson


2003 Honda Civic ex: 8.680 @ 169.000
John Brown, Engine: b18c, Turbos: t72 Tires: gooyear


1990 Honda Civic DX Hatch: 9.200 @ 162.000
Jim, Engine: LS VTEC B18 LS Block and B16 Head, Turbos: T70 Tires: Full Slicks


1997 Honda Civic Coupe Dunlop NoLimit VTG: 9.439 @ 151.000
Witold Karalow, Engine: B16A, Turbos: GT40 Tires: M/T 28


1997 Honda Civic Coupe: 9.665 @ 150.000
Vogelsinger Sandor, Engine: B18B, Turbos: Garrett Tires: Yokohama,M/T


1995 Honda Civic vx hatchback: 9.680 @ 155.000
kyle, Engine: b18c1, Turbos: garrett gt4294r Tires: 24.5x8.5x13 m&h slicks


2007 Honda Civic 8th Civic SI: 9.849 @ 155.960
Everton Carvalho, Engine: K24, Turbos: GTX4202 Tires: M/T 24,5x8


1992 Honda Civic CX: 9.870 @ 145.660
Alexei Guinitaran, Engine: 1.8 L, Turbos: 60-1 Tires: M/T 24.5 x 9


1993 Honda Civic Street all motor : 9.871 @ 138.833
Adel tuning, Engine: drag cartel k26,


1998 Honda Civic Turbocharger: 9.930 @ 142.190
Angela Proudfoot, Engine: B18, Turbos: Turbonetics custom


1994 Honda Civic Coupe: 9.980 @ 145.580
Angel Robles, Engine: 1.8 acura integra gs, Turbos: 60-1 Tires: m&h


1993 Honda Civic cx: 10.050 @ 144.440
joytech, Engine: b18c, Supercharger: n/a Turbos: gt40/ Tires: 24.5 x 9.5


1996 Honda Civic EX Coupe: 10.081 @ 146.430
Shannon, Engine: B18C, Turbos: GT40/35R


1993 Honda Civic cx: 10.200 @ 142.000
dean, Engine: 2.0L gsr, Turbos: ITS 62-1 Tires: 24.5x8.5x14


1992 Honda Civic si: 10.350 @ 141.000
jared wahl, Engine: b18c1 block guarded 82mm stock sleeves, Turbos: t70 Tires: mickythompson 24.5x8x13


1996 Honda Civic DX LS1: 10.395 @ 132.610
Travis Chaney, Engine: LS1, Tires: 26x10.50 Hoosiers


1994 Honda Civic Coupe: 10.400 @ 137.860
John Brown, Engine: 1.8 acura integra gs, Turbos: t3/t4 Tires: m&h


1986 Honda Civic SI, AH5: 10.416 @ 125.000
Jimmy Fernandez, Engine: B16a, Turbos: GARRETT T3/T4 60mm / 63mm Tires: FRONT full slick M/H / BACK 205/R50/15 KUMHO ECSTA


 


©2014 DragTimes - Disclaimer