Removing my Chevy 350 motor and tranny from my '72 El Camino
Yanking out my 350/th350 from my '72 El Camino. Everything was prepped before hand - radiator pulled out, headers/spark plugs removed, power steering unbolted and bungeed, ignition taken out, motor mount bolts removed, driveshaft taken out, crossmember removed, tranny jacked and prepped. This is the end product of the heart transplant. A 454/th400 will be soon be installed and roaring.
Engine and Transmission Removal - '95 Suburban - Part 1
Using the Ford backhoe, we removed the engine and trans combo from the
Suburban. This truck has about 170,000 miles, and sufferred a driveshaft
failure caused by a cracked transmission case. The only fix is to rebuild
the transmission into a new case. Since so many parts were going to have
to come out, it was decided to remove the engine too so it can be gone
over, and freshened up.
Now the project will meet a fork in the road - rebuild the trans, freshen
up the motor, and put it back in? Or just build up a carb'ed 572 and make
lead sled. :)
Chevy Big Block Engine Starting
We just finished our new Chevy Big-Block engine, wich will soon find a home
in our 1980 Camaro. It
is just one of many BBC's that I have built. It is a "street friendly" 10:1
all forged, mechanical roller with too many goodies to list . It sounds
crazy and I can't wait to feel the tire shreading performance.
Transmission removal vids & pics
Don't forget to comment, rate "subscribe" Transmission removal videos, some
videos I took did not work "bad memory card" so this is all I have.
Transmission is a TH700R4 4-speed Auto I am gonna get rebuilt.
How NOT to remove your engine.
Subscribe to my channel, I'm always posting great videos!
About this video, I know this is a bad idea. There were some idiots on the
turboDodge.com forums suggesting that
this was a good idea. I needed to get a blown motor out of my car, so I
setup the camera and demonstrated exactly what can go wrong with this
method. Honestly, I tried to get it down gracefully, in the end I guess I
was lucky it didn't knock the car over in the process. Let this be a lesson
to all, use an engine crane. At least in cars where it's not designed to
come out the bottom.
Extreme Elco Engine Swap! - Roadkill Episode 4
On this episode of Roadkill, David Freiburger, Mike Finnegan and a carsick
dog drive a '69 El Camino 500 miles from home (on seven cylinders) to
change an engine in the parking lot of Summit Racing.
The story goes that Finnegan's wife's grandfather bought this1969 Chevy El
Camino brand new, and it's been passed down through the family, finally to
her. It's a solid car, and the suspension has been hopped up, but the
all-original 350 engine was smoking like a freight train. That didn't stop
the guys from limping it from Los Angeles, California to Sparks, Nevada,
where Summit Racing has a fully-stocked warehouse.
Summit sells every speed part and replacement part on Earth, including the
420hp, 383ci crate engine, so the logic was that the guys would save time
on the engine swap because they could walk right into the store instead of
driving to a parts store multiple times, as they would have back home.
So how long will it take a couple gearheads to change an engine outside in
a snow flurry? Will the EPA shut them down before they can finish? And what
happens when you let a carsick dog ride shotgun? Watch to find out!
Roadkill appears every fourth Friday on the new Motor Trend channel.
Subscribe now to make sure you're in on all the action!
Facebook - http://facebook.com/motortrendmag &
Twitter - http://twitter.com/motortrend
Google+ - https://plus.google.com/101867967859016552744/posts
Website - http://www.motortrend.com & http://www.hotrod.com
How-To Machine a Chevy 350 V8 Small Block Engine
Chris Duke from Motorz TV http://www.motorz.tv takes our Chevy 350 small
block to the machine shop to show you the process of machining a block
Show notes: http://www.motorz.tv/machine-shop/
Watch the complete Chevy 350 engine rebuild series:
1. Tear Down: http://youtu.be/LZO1fWVxN4c
2. Machine Shop: http://youtu.be/e3r3wRBoXkk
3. Bottom End: http://youtu.be/gfrYWKi78zc
4. Top End: http://youtu.be/g46s-Vr4Br0
5. Finale: http://youtu.be/mvJNMN-oP68
Proper way to Lift an Engine #16
Family owned and operated for over 40 years with over 75,000 satisfied
customers. Rated #1 Click on blue link
This video shows the proper way to lift and Engine. Best if Viewed in
Numerical Order. Produced by enginefactory.com Home of the most complete
Live Run Turn Key Crate Engines. Chevy and Ford Performance engine. All
engines are live ran and are Ready to Run out of the Crate. Building Muscle
Car Engines Since 1969
2002 Dodge Ram 1500 Engine Swap 4.7L Part 1 - EricTheCarGuy
Link to full version of this video:
Link to part 2: http://www.youtube.com/watch?v=QES-WrAB1NI
Visit me at: http://www.ericthecarguy.com/
This truck has been a challenge for me over the past couple of weeks as you
will seen in the video. The lesson here is do your best to check the
engine out before you install it and even that may not be enough. Be
careful when doing a job like this especially if you are by yourself as you
can get seriously injured if your not careful so work carefully and
methodically and things should work out fine.
The music is from the site
under "Royalty Free Music", it's title is "Merry Go-Distressed", the
producer of the site allows the use of this music as long as credit is
given, hence the credit given here. Thank you!
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
Visit my Facebook Page:
Be safe, have fun and stay dirty.
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
Small Block Tractor Test Run
This is a short hastily throw together video of me trying out my sister's
pulling tractor. There is something I should make clear before it is asked:
1) Yes I am wearing Crocs.
2) It was laundry day, I don't normally ride around in over sized sweat
pants, tee shirt, and some Crocs.
3) I don't care what you think about Crocs.
one badass sbc chevy 350 2008
SBC 30 over 202/160 steel heads blue racer cam
and yes there is no water pump but we are running water through the block
with a garden hose...thats where the steam is coming from @ the end of the
So let me explain a little something to everyone that thinks they know what
they are talking about
I am no longer building any REBUILT standard / stock 350's Key word Is
stock standard 350.
I am only building NEW 383's and up
YES i know a 383 is a 350 block using a 400 crank...This is the old school
poor man method...which yes I have done and still do on occasion.
But I start now with a brand new DART block a New EAGLE 383 crank and rods
and I have been using Dart Pro comp or to save you some money NKB heads.
I sell the motors complete carb to pan with Intake Distibutor coil wires
water pump fuel pump alternator pullys flexplate starter power steering
pump plugs filter and oil all your brackets and sheet metal Turn key just
add 12 volts a ground and some gas and you ready to go.Turn key crate
engine stage 2 starts at $5,000 @ 500 HP
we also build 406 , 421 , 427 . 434 SBC @ 625 HP and BBC starting @ 505
Cubic Inch 555 and the popular 572 BBC @ 725 HP
ALL BLOCKS HAVE SPLAYED CAPS
any questions email
Engine rebuild part 1
This series is available on DVD Here is the link
We are rebuilding a GM 350 5.7 engine. Now in this particular case we
are also going to upgrade the engine to a 383 6.0 This is called
building a "stroker" motor. In other words we are increasing the "stroke"
of the engine which increased the torq & horsepower.
If you are able & wanting to rebuild an engine, this video should give you
a good overview of what to do. If you are having someone else build an
engine for you, you will be able to see what's involved in the process