1998 Honda Accord V6 With Open Headers
This is my 1998 Honda Accord EX-V6 with a J30. It's automatic but I was
creative to put a bag over my shifter. This is my dad's car but I've helped
him put it together since we've first got it. Please no haters, im just
here sharing my car. Hope you like.
Honda Accord VS Lamborghini Murcielago. EXOTIC CARs RACING, TOUGE FUN!!
found a pack of Exotic cars meeting up, so i sayed.. hmmm this could be
so i joined in with my little Gas Saving Honda to race these high end
Performance Cars!! XD
good racing and fun! too bad there was so many cars that the racing was
very limited.. =/
and if you may ask about my car, its;
naturally aspirated (all motor) Frankenstein H/F series putting out 234whp
built by myself (", )
end of the video: the whole pack of cars cruising by.
AFAccord's F23 Turbo Accord - HD Vids and Dyno
I only had a week to drive the car after it was tuned and wasn't able to
wire up my ECU switch in time to get any high Boost runs on video. Sorry guys! I'll make
plenty of high-Boost videos when I
come home, so subscribe!
Music rights belong to Gemini - Graduation of AEI Media.
Parts and Specs:
-F23 block, bored to 86.5mm
-Wiseco K20 spec pistons @ 10.5:1 compression
-SwainTech ceramic coating on piston crowns
-Crower F23 rods
-OEM main bearings (pink across all journals)
-ACL HX rod bearings
-Kaizenspeed balance shaft delete kit
-Bisimoto heat-shielding intake manifold gasket
-Bisimoto Pro valve springs
-Bisimoto Pro valve retainers
-Bisimoto cam gear
-Innovative 65A engine mounts
-Maxbore F23 throttle body
-MFactory limited slip differential
-DIY ramhorn turbo manifold
-DIY 2.5" charge piping from CXRacing
-28"x8"x3.5" FMIC from Go-Autoworks
-Triple-core half-size radiator from Go-Autoworks
-3" Straight pipe Exhaust
-3" Vibrant Flat black muffler
-Garrett T3/T4 57 trim turbo
-ACT Xtreme pressure plate
-ACT Streetlite flywheel
-ACT performance street disc
-Tial 38mm wastegate
-Tial Q BOV
-P61 OBD1 ECU
-Tuned using eCtune by the infamous... Joseph Davis!
How To Pull Honda Codes Without a Scanner -EricTheCarGuy
Link to code explanations:
Honda ABS Codes 1994-1997:
Honda ABS Codes 1998 and up:
Visit me at: http://www.ericthecarguy.com/
Discussion about this Video:
I feel like I should have made this video a while ago but the opportunity
never came up. Since I had this RL in my shop that had a check engine
light AND an ABS light I thought it was a perfect opportunity to put this
video together. I get asked all the time about my 'special tool' and it's
really nothing more than a Honda 2 pin connector with the input wires
soldered together. These connectors might be harder to find than you think
but if you run across a junk honda and one of these is on the harness grab
it. Even if you don't have the tool a paper clip or piece of wire will do
the exact same thing so don't sweat it if you don't have the tool because
shorting the connector is all you need to do.
I hope you find this video helpful.
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
ALL NEW ACCORD TRIBUTE
WELL THANKS TO THE PPL THAT HAVE ALL THESE NICE ACCORDS.... COULDNT HAVE
DONE IT WITHOUT YOUR PHOTOS...
Junkyard Turbo Swap! Chevy-Powered 1971 Datsun 240Z Autocross Thrash - Roadkill Ep. 26
What do you get when you cross a rusted 1971 Datsun 240Z with a Chevy 4.3L
V6 and a turbo from a Ford Power Stroke
Diesel? The Rotsun! During Roadkill Episode 25, Freiburger and Finnegan
revived the Rotsun expecting it to dominate in the 9-car autocross showdown
of previous Roadkill project cars. It also needed to beat a 2014 Kia Rio 5,
but failed to do so with the Rotsun shamefully breaking down before
completing a decent lap. So in this episode: revenge. After swapping in the
mismatched turbo and making nearly 400
rear-wheel horsepower, the guys head to
the autocross at the Goodguys 5th Spring Nationals in Scottsdale, Arizona
and mingle with fans on their way to a rematch with that dastardly Kia.
Roadkill appears every fourth Friday on the Motor Trend channel.
Subscribe now to make sure you're in on all the action!
Facebook - https://www.facebook.com/RoadkillShow,
http://facebook.com/motortrendmag & http://facebook.com/hotrodmag
Twitter - http://twitter.com/motortrend &
Google+ - https://plus.google.com/1018679678590...
Website - http://www.motortrend.com & http://www.hotrod.com
92 Accord Turbo Compilation
a collection of clips from my CB7 accord G22 turbo. 530whp pump fuel 18psi Meyagi Tuned!
* motor is sleeved with an 88mm bore, CP/Carrillo internals, fully built
and ported head, 1200cc injectors. Tuned on CROME. Car was built/tuned by
myself on a budget, no sponsors (no mommy and daddy $) Car is built to take
the abuse, its been running strong for 2+ years, seeing rev limit every
day, and all clips that were shot on the road are on 17" street tires.
Track clips are on 26" MT drag radials.....
Thanks for watching,
how to turbo your honda over the weekend
UPDATE: for all those who think this method means the motor wont last, here
is a video from friday april 5th 2013 of the car still running strong, its
been over a year and around 10k miles of hard beating.
UPDATE: ALSO CHECK OUT MY SECOND VIDEO ON HOW TO turbo YOUR HONDA you can see it here
this video shows the steps to turbo your
honda in a couple days with upgraded internals and not removing the engine
or doing any machine work.
also for those saying you need to do some sort of easy break in period i
think you need to read this article , the old fashioned ways are long gone