Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

E46 330ci carbon airbox

Ebay airbox


 


More Videos...


How to Make a Fibreglass or Carbon Fibre Car Airbox
No.5 Redline Tutorial, showing 2 easy methods step by step for improving airflow into your engine.





Cool Secret Tips And Tricks About Your E46
A few tips and tricks that you may perform on your e46.





AEM Intake Installation - E46 BMW 325 - 12 Step Program
http://www.fuelculture.com/aem/cold-air-intake-system-21-672 We take our 2001 BMW 325xi and install AEM intake Part #21-672 (http://www.fuelculture.com/aem/cold-air-intake-system-21-672). Follow this installation to see how easy it is to complete an AEM install on something as simple as your driveway. Here are the Steps we highlight in the video. Step #1- Remove the AEM Intake System (Part #21-672P) from the box and verify all pieces are intact. Step #2- Remove old (or factory) intake. Disconnect the assembly from the vehicle's Mass Airflow Sensor. Step #3- Underneath the intake is a rubber mouth. Unclasp the mount and pull it straight off. Step #4- Secure the AEM Heat Shield using the supplied washers and a 10mm nylok nuts. Step #5- Slip the silicone coupler over the MAF sensor with the supplied hose clamps. Be careful not to over-tighten the clamp. Step #6- Slip the intake piping into the other end of the coupler and tighten the second hose clamp. Step #7- Raise the front of the vehicle with a jack. Support the vehicle using a properly rated jack stand. Step #8- Remove the lug studs using a 17mm socket in order to remove the left front wheel. Step #9- Using a 8mm socket, remove the bolts securing the lower splash guard. Step #10- Attach the rubber mount to the open point under the headlight assembly. Attach the intake bracket using the supplied nuts and washers. Step #11- Install the optional AEM Dryflow Pre-Filter (Part #1-4000). Step #12- Install the AEM Dryflow Air Filter over the secured intake piping using the last hose clamp.





2005 BMW E46 3-Series Control Arm Replacement
Click here for products featured in this video: http://www.apdty.com/searchitem.epc?lookfor=631020,631031,016912 In this video we'll show you how to replace the control arms and bushings in a BMW E46. This job is also similar to other cars in the 3-series lineup, including the E36.





■BMW 3 Series Production BMW Munich Plant Full HD 1080i
BMW 3 Series Production BMW 3 Series Production BMW Munich Plant Full HD 1080i plant series http://www.youtube.com/watch?v=f_VtNqpgUXE http://www.youtube.com/watch?v=vSJaQHRn5c4 http://www.youtube.com/watch?v=qhCXFsQ6kKQ





BMW E46 330d on max speed ( unplugged ) :-)
The result of a discussion, how fast a series E46 330d can go. The car reached a speed of 256 (GPS ). One can see on the consumption indicator, that the car is limited to 250km/h ( +x ). The steering unit stops the supply of diesel.





Dinan Cold Air Intake BMW 323i Before And After
this is a carbon fibre dinan cold air intake that we installed, i record the car revving and accelerating before the new intake, then we install the intake then take a new video of it revving, and accelerating. the sound is just awesome that this beast makes....





BMW 325i Carbon Airbox sound
Carbon Airbox fitted on a BMW 325i E36





BMW 3 E46 - Большой тест-драйв (б/у) / Big Test Drive - БМВ 3 Е46
Сайт: http://btdrive.ru/ | Twitter: http://twitter.com/bigtestdrive | G+: https://plus.google.com/107490113575465327649 | Instagram: http://instagram.com/bigtestdrive | Facebook: http://facebook.com/stillavinpro | Vkontakte: http://vk.com/stillavinpro По признанию Сергея Стиллавина если бы не его габариты, то он давно бы польстился на автомобиль, ставший героем сегодняшнего выпуска б/у-версии "Большого тест-драйва". При каких обстоятельствах и за какую сумму приобрел BMW 3 E46 его нынешний хозяин Дмитрий, что ему пришлось сделать с автомобилем, получилось ли у Сергея Стиллавина комфортно разместиться за рулём машины и что удивило Рустама Вахидова.





Большой тест-драйв (видеоверсия): BMW 3 серии
Все наши тесты: btdrive.ru В «Большом тест-драйве» автомобиль, который Сергей Стиллавин хотел бы иметь в своём владении, Рустам Вахидов признает его высокое качество, но отмечает небольшие проблемы с управляемостью, а Виктория Колосова заявила, что он (автомобиль) «ну... красивый».





BMW E46 M3 AFE Magnum Force Intake Installation
View this BMW Repair Tech Tip - follow this link: http://www.bmpdesign.com/technical/fuel/files/BMW_E46_M3_AFE_Magnum%20Force _Intake_Installation.php This Video is the start to finish installation procedures for the AFE Stage 2 Magnum Force Intake Kit on a BMW E46 M3





Part 1: Installing shocks, struts and springs on a BMW 3 series 99 thru 05 (E46)
BLOG ARTICLE: http://blog.bavauto.com/14307 "Like" us on Facebook - http://www.facebook.com/BavarianAutosport "Follow" us on Twitter - http://www.twitter.com/BavAuto "Subscribe" to us on YouTube - http://www.youtube.com/BavarianAuto Visit our online store - http://www.bavauto.com/ All of the items shown in these videos are available in our online store at http://www.bavauto.com/. Need additional tech help? Please visit our tech blog for thousands of Tech and DIY BMW and MINI articles at: http://blog.bavauto.com/ --- In Part-1 of this two part series, we will replace the front shock/strut/spring assembly. See Part-2 for the rear shock and spring replacement. The Bentley repair manuals will cover standard shock and spring replacement for the various BMW and MINI models. This DIY will assume that the DIYer has the applicable Bentley manual for additional reference as well as fastener torque values. Note that we will be installing the Bilstein PSS-10 coil-over kit. However, the procedures would be the same for any common shock/strut replacement (including installing sport springs, if desired). PARTS USED: • New shocks/struts (Bilstein, Koni, Sachs, etc.) • New sport or stock replacement springs, if desired (BMW, BavAuto, Eibach, etc.) • New Shock install kits (compression bumpers, dust shields, spring pads, etc.) • New upper strut and shock mounts • New strut & shock mount gaskets (as required) • Rear shock mount reinforcing plates TOOLS USED: • Bentley Repair Manual • BavAuto Non-Marring pry bar set * BavAuto spring compressor tool • 13mm through 18mm ½"drive socket & ratchet set with various extensions • 4mm through 8mm Allen keys or bits (for ratchet use) • 13mm through 18mm combination wrench set • Assorted flat and Phillips screwdrivers PROCEDURE: FRONT (applies directly to the E46 3-series, but others are similar): 1) Safely raise the front of car, with suspension hanging. 2) Remove the wheels. 3) Disconnect the upper end of the swaybar link from the shock/strut bracket. Note that the through-stud for the link's upper joint (as well as the lower) must be secured using a 16mm to 18mm thin open end wrench. This particular link is 16mm. 4) Remove the strut mounting pinch-bolt. The bolt goes through the strut mounting clamp on the wheel hub/spindle assembly and has a nut on the opposite side (some models do not use nuts, the bolt threads into the clamp). 5) Set the mounting bracket for the ABS sensor wire, brake pad wear sensor wire (left side only) and brake fluid hose aside. Note that other models may have these hoses mounted in a bracket that is affixed to the shock/strut housing. In these cases, remove the wires and hose from the bracket. 6) If the vehicle has adaptive headlights (self-aiming), disconnect the sensor link from the control arm or the sensor bell-crank arm. The sensors may only be present on one side of the vehicle. 7) Place a support or jack under the lower control arm to support the suspension as the upper strut mount nuts are removed. 8) Remove the three 13mm nuts that secure the upper mount to the body (strut tower), under the hood. 9) Gently lower the jack or support, from step-6, and lower the strut assembly. Pull the strut assembly up and out of the hub/spindle. A helper may need to push down on the hub/spindle as you pull the strut upward. If the clamp is too tight for the strut to pull out, use a cold-chisel or large flat-blade screwdriver as a wedge to open the clamp a bit. Tap the wedge into the split in the clamp, widening the clamp, allowing the strut to be removed. 10) Once removed from the hub/spindle clamp, remove the strut assembly from the wheel well area. 11) Install a spring compressor to the spring on the strut assembly. Compress the spring until you can tell that the spring pressure is relieved from the upper and lower spring seats. 10) Remove the upper shock/strut nut that is at the top of the assembly, in the center of the upper mount. To remove the nut, you can use the method shown in the Spring 2007 issue of our Fast Times newsletter, page-7, or you can use an impact gun. DO NOT use an impact gun for re-assembly! 11) Once the nut is removed, disassemble the upper mount, upper spring perch and washers from the shock's piston rod. Keep track of the various washers and their locations. 12) Pull the spring (and compressor) off of the shock/strut. 13) Assemble the new shock/strut and/or spring. 14) We're sorry, but the description can not be any longer (youtube requirement). Watch the video and see our tech blog for the full DIY steps at http://blog.bavauto.com/ -------- All products noted in this video can be purchased in our online store, http://www.bavauto.com/, 24 hours a day, 7 days a week. e-mail us at info@bavauto.com or call our headquarters and speak to our knowledgeable advisors at (800) 535-2002 (Mon.-Thurs. 8AM to 9PM EST, Fri. 8AM to 7PM EST, and Sat. 9AM to 4PM EST).





CARBON-AIRBOX on DYNO-PULL .....- BMW ///M3 E36 3.0 Drift
carbon.airbox no Dyno-pull the M3 E36 3.0 from the DRIFTER "benno frieden"





BMW E36(325i).Легенды 90-Х.Тест-драйв.Anton Avtoman.
http://vk.com/id132523895 Добавляйтесь в друзья!) http://www.facebook.com/anton.vorotnikov https://plus.google.com/u/0/110807444081517706579/posts http://instagram.com/antonvorotnikov





BMW 335i vs Audi S4! - Head 2 Head Episode 10
On this episode of Head 2 Head, Carlos Lago pits the new 2012 BMW 335i against it's natural rival from Ingolstadt - the 2012 Audi S4. The 3 Series has long enjoyed its reputation as the benchmark of European sports sedans. But does the more powerful S4 finally have what it takes to end BMW's reign? Head 2 Head appears every other Wednesday on the new Motor Trend channel. http://www.youtube.com/motortrend Subscribe now to make sure you're in on all the action! http://www.youtube.com/subscription_center?add_user=motortrend Facebook - http://facebook.com/motortrendmag Twitter - http://twitter.com/motortrend Google+ - https://plus.google.com/101867967859016552744/posts Website - http://www.motortrend.com




Which car is faster? Which Car is Faster?





Similar 1/4 mile timeslips to browse:

2001 BMW 330Ci AA: 12.776 @ 105.830
Ryo, Engine: M54B30, Supercharger: Rotrex C38-81 Turbos: N/A Tires: Cooper RS3


2001 BMW 330Ci : 12.858 @ 103.950
PEI330Ci, Engine: 3.0L Inline 6, Tires: 26


2001 BMW 330Ci AA: 13.073 @ 104.450
Ryo, Engine: M54B30, Supercharger: Rotrex C38-81 Turbos: Stock Tires: Cooper RS3


2001 BMW 330Ci ZSP: 13.689 @ 99.960
Julio, Engine: m54b30, Tires: 255/40r17 sumitomo htrz


2005 BMW 330Ci ZHP: 13.974 @ 100.330
John, Engine: ecis intake,


2001 BMW 330Ci Headers and Exhaust: 14.300 @ 99.210
SWINFORD, Engine: M54B30, Tires: General Exclaim 255/35 Rear 235/40 Front


2004 BMW 330Ci coupe: 14.976 @ 93.810
Eric Chang, Tires: Yokohama AVS sport


2003 BMW 330Ci : 15.263 @ 92.060
Scott, Engine: Stock, Tires: 205 50 vr 17 Goodyear RSA


2002 BMW 330Ci : 15.322 @ 91.440
Joanne, Engine: Stock, Tires: Continental


2005 BMW 330Ci Convertible with Performance package: 15.430 @ 97.000
Kevin,


2003 BMW 330Ci : 15.520 @ 92.850
Rob, Tires: 225/45 R 17


 


©2014 DragTimes - Disclaimer