This is how I have started making a accessory drive plate for my 1979 Ford F350 Crewcab 4x4. I received a scrap "D9TE-AB" 1979 Ford 460 engine block from a guy on the 460forddotcom website. I am making a true reverse rotation water pump setup using a single drive belt. I also will be adding an additional York Style A/C compressor to use for on-board-air. I plan to update the video as I progress, so check back often.
vw beetle with v8 ford 460
this started off as a frame off restoreation to be put back to stock, but
half way through it turned into a big block V8 project 460 BB i will be
posting this as i go keep checking for part 2 and so on until its done
460 Ford Cylinder Head Blueprinting and Preperation for mapping and Porting
Anthony explains how to set up a Ford 1973 460 Ford head for the begining
of blueprinting for a maximum effort full on 1/4 mile race car using a 1993
fox body to get the car in the mid to high 10 second range using PUMP GAS.
The process known as "removing casting flash" is critical in not to remove
any material in order to "mark up the port". Anthony explains how to use
the best die grinder on the planet, the dotco 10 11 2B with 8 inch
extention with custom side Exhaust and
high speed impellers.
Ford 460 Tunnel Ram Set Up w/ Holley Carbs By Proformance Unlimited
Watch the live run of our Ford 460 crate engine with 500hp....Engine
features a Tunnel Ram Setup by Weiand and Holley Carburetors...If you would
like information on this engine build, please contact us at
800-267-3940...You can also visit us on the web at
Twin Turbo 1977 Chevy Monza Spyder.wmv Dyno video of my
brothers Twin turbo 1977 Monza Spyder.
Has a 355 Small Block, Accel DFI, Gen 6, Dual TPI Throttle Bodies, Intercooler, Twin turbos using Gale Banks turbo manifolds, Dodge Viper T56 6 Speed
transmission, Ford 9" Inch rear, with 4 wheel disk brakes. Ran out of Dyno time, but made
497.66 HP and 530.01 Ft Lbs or Torque at 7 PSI. Better description
Project 460 Fox Mustang Part 2
Porting and polishing the cylinder heads, assembling and firing up the 460.
This engine was built for Project 460 Fox Mustang when the plan was for a
street/strip car. After finding a super deal on a lot of go fast(er) parts,
the plans have changed. This engine will be sold and a new, more powerful
motor will be built for mainly drag racing. To see the engine run, skip
ahead to 5:50. Thanks for watching!
Specs on this engine are...
1978 460 Ford Engine Std. bore
New Speed Pro flat top pistons
new rings and bearings
new high volume oil pump and pickup
new Fox Mustang oil pan
New Edelbrock Performer RPM intake manifold
New HEI distributor
New Summit hydraulic cam .503 lift 280 duration
D3VE cylinder heads ported and polished
Holley 780 cfm vac secondary carb
Ford Model T Half engine
I cut this T model Ford engine in half in 1957 using 11 hacksaw blades.
The only part not cut with the hacksaw was the camshaft as it was too hard
and had to ground through.
pvc train horns 2
Hello, sorry it took so long finally got a better video made everyones been
asking for a close up and stuff so here ya go. Any questions just let me
know ill try and get back too you when possible. 4 horns mounted on the top
of my truck cap, york compressor model 210, pressure switch and propane/
air tank 5 gal. Built these myself not the same as dozerboymillers but
similar. I dont have plans for these i am in the process of making another
set that i will probably post on ebay i will make a vid of them on here
first so you can see and here what youll be getting.
1979 CJ5 Spinning Tire.AVI
This is a short video of my brothers Orange 1979 Jeep CJ5. It has an
Aqualu aluminum tub which was a shame to cover in paint, because the welds
were almost like artwork. It also has a Dana 60 Rear axle, Dana 44 Front
axle, Throttle Body Injected Chevy 305, GM Muncie SM465 Transmission, and
Spicer 20 transfer case. It also has a 1979 Ford F250 windshield wiper
motor driving the spare tire. The tire is mounted using a spare spindle,
hub, bearings, and locking hub incase he breaks one while wheeling. He bent
up the roll cage which is tied into the frame as well as made the swing out
cooler and tire mount. I took this video at the Bloomsburg 4 Wheel and
Offroad Jamboree on July 9th 2011.