Recent updates here!!!
Small vid of my new mazda RX7 FC turbo II.
Overhauled engine with streetport.
corksport 3" Exhaust
And more to come in the futrure
Part 12: 13B Rotary Engine Rebuild - My 76 Mazda RX-5 Cosmo Restoration
Just as I promised last episode, it is finally time to build the engine!
Part 12 of my RX-5 Cosmo restoration covers the entire process of building
the 6 port 13B Mazda rotary engine. While this engine is a hybrid of GSL-SE
RX-7 and Cosmo parts, the process is the same for any rotary from a 12A to
a 13B NA, 13B turbo, 13B-REW or any
other variant of the 13B. This video shows the whole process of the engine
build, starting from measuring the rotors and covering everything else
including clearancing the side seals, assembling the rotors, complete
assembly the short block, setting the eccentric shaft end play and
installing the front cover and everything underneath it. It's probably the
most complete engine build video outside of what you can buy from the
vendors, and as such, is an hour long. After this one, I'm going back to
videos under 20 minutes. But for now, grab a beverage of your choice, sit
back, and enjoy.
1650 HP RX7, "The Sleeper Part 2", Scary and Funny, from NRE.
Nelson Racing Engines 1650 HP RX7 road video of this crazy sleeper.
Awesome power in this tiny car. This car is really scarry and very fast.
Some very funny video. I laughed a lot. More information and downloadable
videos for your IPOD and PS3 can be found at at
http://nelsonracingengines.com. and http://nelsonsupercars.com.
Mazda Rx-7 FC3S DYNO
Gabbar's powered T04s!
Listen to the wastegate scream O__O
RE Amemiya AW7's 18x9 +17
353 WHP low Boost 10 psi @ 7k
(CRXQ) RX7 ( FC3S ) Complete face lift
Wanna see our videos with the real songs?
Go here: http://user.streetfire.net/profile/Lomansik.htm A nice montage of
rebuilding and RX7. Lots of time and money was invested in that car, to
"refresh" the stock look and the results are stunning. Ebverything is
rebuilt or new. Enjoy the show!
1988 Mazda Rx7 NonTurbo Streetported redlining
1988 Mazda Rx7 streetported na redlining through the gears, for the record
i could of revved all the way to the end of the tach which is 8000rpm, so
this isnt 100% of what the car could of done ( for those questioning my
car's engine temp, my car is running at operating temp, its normally 1/4
of the way up fully warmed up..the car isn't redlining cold)
Racing Beat streetable header, straight pipe in place of cat, Borla 2.5"
catback Exhaust, K&N cone intake,
ported throttlebody, removed secondary throttlebody plates, lightweight
steel Racing Beat flywheel and Centerforce Dualfriction clutch, removed
5th/6th auxilary ports/sleeves/rods and actuators
my old Mazda RX7 FC3S Turbo2 in a tunnel
my project 1988 Mazda RX7 turbo2 going
in a tunnel.
Car was stock, open air box, blitz bov, and custom 3" straight pipe Exhaust,...you can hear a lot of
for pics and infos on my RX7:
CHECK OUT MY OTHER VIDEOS!!!
First Drive - '87 RX7 Turbo II Project
Rtek7 Stg 2.1 ECU, 4 x 7200cc, 255lph Walbro, BNR Stg 1 Hybrid turbo w/30mm WG, RB Downpipe w/ Straight 3" pipe
to N1 Styled Cans, Stg 2 Clutch, KYB AGX's, NGK A/Fx Wideband,
This is just a test drive, there is still a lot to do to it before it's
really streetable as a daily driver.
Nitrous LSx Mazda RX-7 vs E85 Big Turbo EVO on slicks!
EVO HAD CLUTCH ISSUES REMATCH COMING SOON!!
OutOfOrder EVO vs DNR Performance LSx RX-7
Shoutout to 3HeadedElephantS for the GoPro Footage! Checkout his channel
and subscribe, also watch his badass edit of this same race here: