How To Install Replace Window Regulator Chevy GMC Pickup Truck SUV 88-98 1AAuto.com
1A Auto shows you how to repair, install, fix, change or replace a broken, cracked, damaged, slow-moving, or stuck power window regulator and motor. This video is applicable to the 88, 89, 90, 91, 92, 93, 94, 95, 96, 97, and 98 Chevy and GMC Pickup truck and SUV models.
How To Install Replace Window Motor GMC Sierra 99-06 1AAuto.com
1A Auto shows you how to repair, install, fix, change or replace a broken,
cracked, damaged, slow-moving, or stuck power window regulator and motor.
This video is applicable to the 99, 00, 01, 02, 03, 04, 05, and 06 Sierra
and Chevy Silverado models plus 00 to 06 Tahoe, Yukon, Escalade SUVs.
1AAuto Auto Repair Change Rear Axle Differential Cover Oil Fluid (non-posi)
If you have been driving your car or truck in extreme conditions or even
consistently rainy conditions you may want to check your differential
fluid. These installation instructions and tutorial will show you the steps
involved in changing your rear axle lubricating fluid. This video is
applicable to the Chevy S10 Pickup, years 94, 95, 96, 97, 98, 99, 00, 01,
02, 03, and 04.
How To Install Replace Rear Trailing Control Arm GM Front Drive 88-08 1AAuto.com
1A Auto shows you how to replace a rear control arm on a 1992 Chevy Lumina.
This is the same process for many GM Front Drive Cars years 88, 89, 90,
91, 92, 93, 94, 95, 96, 97, 98, 99, 00, 01, 02, 03, 04, 05, 06, 07, and 08
such as Pontiac Grand Prix, Buick Regal Olds Cutlass Supreme and more.
Door Hinge Pin
As trucks get older the doors begin to get hard to close. Often times the
hinge pins are simply worn out. There not that hard to replace. The kit
is pretty cheap and there is a tool that doesn't cost much either. You can
try to get the spring back in place without the tool, but after you work
on it for an hour you'll wish you had the too.
Replacing the inside door handle on a Suburban for under $15
Here's how to replace the inside door handle found on many Chevrolet and
GMC SUVs and trucks. The video here shows replacing a 1999 Suburban's
I purchased the replacement handle in the video from Amazon for $13 with
free shipping. http://amzn.com/B000B68C08
You only need...
Two flat head screwdrivers
#12 1 in sheet metal screw
Drill with a 1/8 to 3/16 dill bit
Pliers (Long-nose would be best)
Hex head screwdriver or ratchet (for the two screws in the arm rest. some
models use Phillip heads instead.)
Disclaimer: All products used in this video were purchased by me and all
video content is my own and has been edited by me, Matthew Fox.
LMC Truck: Shortbed Conversion [S7 Ep. 3-1]
Everybody wants a classic short bed pickup. Unfortunately short beds are
hard to find for a good price... but, long beds are a dime-a-dozen, and
cheap! The solution?...chop a long bed down! That is exactly what Stacey
does on this episode of GEARZ. He takes a classic 67 Chevy long bed, and
walks you through the way to cut the frame properly, so you have a safe and
reliable truck when you are done. If you've heard about this kind of
modification, but always thought it was too difficult or involved for you
to do, you need to watch this episode of GEARZ and let the cutting begin!
How car window regulators work
This video shows how a window regulator works in a car or truck. It also
shows how easily they can break and why they have to be replaced.
Headlight Lens Restore using Toothpaste!
CGHQ Website: http://www.classicgamershq.com
Headlight lens restoration using regular toothpaste is real. It doesn't
take much effort, but the type or brand of toothpaste does make a
difference. Watch to see the results i came up with.
How To Perform a Parasitic Draw Test - EricTheCarGuy
This video has been a long timing coming and is one of the most requested
things I get is about batteries going dead overnight so I'm very happy to
finally bring you this video about the process of finding a parasitic draw
which is a small drain on a battery above 50ma when the vehicle is shut
off. Once you find the right fuse(s) the next step is to trace the
components involved in that circuit till you find the source of the draw,
you first start with a wiring diagram to give you an idea of where to start
looking and then start unplugging things in that circuit to isolate the
cause, it's quite scientific really a simple process of elimination. Here
is a link to BBB's site that you can use to look up wiring diagrams for
Good luck and if you have anymore questions check the database on my
website and if you don't find what you're looking for there then post your
question to my forum, here's a link.
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
Visit my Facebook Page:
Be safe, have fun, and stay dirty
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.