2002 Cavalier Water Pump Replacement (Part 1) - EricTheCarGuy
Visit me at:
See part 2
This is part one of the 2 part series I've done on the replacement of the
water pump on this 2002 Chevrolet Cavalier with a 2.2L engine, this is the
older version of the 2.2 with the vin digit #4 not F, the newer version has
an updated design and is nothing like the engine in this video so if you're
a bit lost that is probably why.
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
Visit my Facebook Page:
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
Instagram - MarkFreeman408
Sunfire doesn't start for us so we take the trucks out mudding!
Pontiac Sunfire 2001
Lambo doors, 2.2 L turbo, projector
headlights, SSBC Corvette conversion, 14 monitors, Xbox 360, chrome and
1997 Pontiac Sunfire - Exaust Through Hood
This was my Demolition Derby car I ran at Campbellford 2008. I was given
this car from a friend of mine who ran it in a Figure 8 race and the car
was sitting for a year and a half before we got it. So this is a start-up
movie and showing how a stacked 2.2L GM sounds. Enjoy!
VXR Turbo Install on Z20LET Astra G
Astra turbo. In depth installation guide
of Z20LEH turbo unit in a MK4 Opel Astra
with Z20LET engine.
This is a one man job and can be done easily if you have the confidence and
the right tools.
With recommended oil restriction mod.
Available from http://myworld.ebay.com/24kturbo/
2004 Pontiac Sunfire Coupe: Ode to a Great Car
For the past 110,000 miles, this car has been a wonderful driving partner.
GM gets a lot of bad press, but I've had a singularly good time with this
I purchased it brand new in 2004 for just over $10,000, and I've had to
perform/pay for only minimal repairs since then. I've gotten fantastic
mileage, all-weather performance, and quite a few looks from passersby.
I'm picking up a 2009 Dodge Charger SXT AWD in the next couple of weeks,
and I thought I'd commit to celluloid some of the fun I've had with my
little two-door. I'll certainly miss it.
Wheel Bearing Replacement with Basic Hand Tools
Front wheel bearing replacement on a 2002 Buick LeSabre with basic hand
tools. Please note, this vehicle has the bearing built into the hub. Some
vehicles may have a taper rolling bearing (usually older vehicles have this
setup) or some vehicles may need the bearing to be pressed out of the hub.
In this case, the hub & bearing is all one unit. Don't forget to wear
This video is being performed by an experienced tech. Any attempt to repair
automotive parts and/or systems carries risk of personal injury. Always
adhere and follow safe practices when working on vehicles. Such as, use
safety glasses, jack stands, no loose clothing, etc. No guarantee or
warranty is implied. Use the information in this video at your own risk.
How to Change a Wheel Bearing (long and detailed version)
This video shows how to change a pressed bearing in a Ford, specifically a
95 Ford Windstar, but this method will be similar for all pressed bearing
vehicles. The main steps are to take off the spindle nut, tire, brake
caliper, and rotor. Then remove the bolts from the lower control arm ball
joint, tie rod, and strut. Remove the steering knuckle, then press out the
bearing and hub/spindle. Then press in your new bearing and hub/spindle.
This job is a little more complex but can still be easily done by any
amateur mechanic. You will save $400-800 depending on your vehicle. Pleas
comment, like and subscribe if you liked this video!
**If the video helped, please give it a "thumbs up" and consider
Leave any questions or comments below and I will answer them as well.**
My Facebook: https://www.facebook.com/chrisfix8
My Twitter: https://twitter.com/ChrisFix6
Here are some other similar how to videos (there are a lot more than this):
How to change brake pads:
How to replace drum brakes:
How to change an Alternator:
how to remove a pressed front bearing, how to remove a front bearing, 2003
Mazda Front Wheel Bearing Replacement (Press In Type Bearing), How To
Remove Pressed-on Bearings - EricTheCarGuy, Wheel Bearing Removal with
Harbor Freight Universal Tool BMW 325i Rear Front, bearing, press, pressed,
pressed bearing, front bearing, front wheel bearing, diagnose, how to, diy,
ford, windstar, ford windstar, Pressing out a front wheel bearing, harbor
freight, bearing kit, How to: Remove & Install A Truck Hub Bearing Assembly
with Timken, How to remove a rusted wheel hub bearing assembly the easy
way, trick, mazda, ford, lincoln, gm, truck, van, car
Due to factors beyond the control of ChrisFix, it cannot guarantee against
unauthorized modifications of this information, or improper use of this
information. ChrisFix assumes no liability for property damage or injury
incurred as a result of any of the information contained in this video.
ChrisFix recommends safe practices when working with power tools,
automotive lifts, lifting tools, jack stands, electrical equipment, blunt
instruments, chemicals, lubricants, or any other tools or equipment seen or
implied in this video. Due to factors beyond the control of ChrisFix, no
information contained in this video shall create any express or implied
warranty or guarantee of any particular result. Any injury, damage or loss
that may result from improper use of these tools, equipment, or the
information contained in this video is the sole responsibility of the user
and not ChrisFix.
Z06 vs Cavalier??? (and more)
A whole bunch of street racing from smack dab in the middle of the midwest.
Z06, Camaro's, a crazy
turbo Cavalier, an Evo & STi, and 700hp
S2000 battle it out on he streets.