P2646 Honda Accord ,VTC strainer
P2646 Honda Accord ,VTC strainer. This Honda would not run at higher
speeds. It would start bucking and stall out if held to the floor. After a
bit of cleaning it seems to run fine. Do not try just removing the screens.
If you try to run a Honda with out the VTC strainer any dirt that the
screen would of caught will now go in to the little oil passages and be
hard to remove. I am also Leary of trying to add cleaners to the engine
when experiencing VTC Strainer problems.If the debris stuck in the VTC
Strainer bad enough to set a P2646 code then I would be afraid the debris
would break down smaller ,get through the VTC strainer just to get caught
up in the valve train oil passages.
05 TSX Js Exhaust Full Bolt Ons - Driving and Pulls
Sorry guys didnt feel like editing the non exciting parts out :P
Anyways mods are as follows:
Stock internals k24a2
Custom cold air intake
Exedy 8lbs Fylwheel
Exedy stage 2 clutch and pressure plate
RDX injectors - doesnt add power but whatever
Car was mainly street tuned but it was tuned on the Dyno once. All tuning was done
It was 84 degrees and very humid today :/ but at 78* with IATs at 87 it
My B18 Type R VTEC Classic Mini
The engine is a B18c6 from a Honda Integra, 197hp.
Subframe is a Watsons kit. Was fitted by Watsons Rally UK.
Recorded with a GoPro Hero HD.
Before video with the old 1380cc engine...
Accord Type R VS CRX ED9
Speednation 2011 CRX komplett leer mit Plexiglasscheiben und original Motor
D16Z5 nur Chip und geändertes Differential. Accord komplett Serienmäßig
Honda Accord VTEC timing belt and water pump Honda Accord VTEC High Detail How to
You can buy a quality belt and water pump online here
Special thanks to Spanky for filming this video for me. : ) My last
Honda Accord video was
very well viewed, but lacking in good sound, stability, and lighting so I
did another one with some help. Enjoy High Detail How to do a timing belt
and water pump Honda Accord VTEC
Honda Accord VTEC Solenoid Gaskets Replacement
In this video I show you how to replace both VTEC solenoid valve gaskets
(valve to cylinder head and solenoid to valve) on 1994-1997 Accords.
This is a common cause of oil leaks on the upper passenger side of the
engine next to the distributor shaft seal, distributor o ring, and valve
It seems the same engineers who buried the Accords fuel filter also decided
to make the VTEC solenoid valve difficult to remove as well. One of the
bolts for the valve is buried so deep you have to partially drain the
cooling system and use a u-joint to get it out.
I take your through the process step by step from removal of all the parts
to re installation.
This video ran a bit longer than I wanted it to but considering how
deceptively easy this job looks at first glance (until you can't get that
one remaining hidden bolt on the valve off to remove it) I decided to leave
in as much detail as possible.
You will need to add new coolant and bleed the cooling system to avoid
engine damage after you're done. If you need that info here is the link to
my cooling system bleeding video.
Honda part numbers used in the video:
Solenoid to valve gasket: 36172-P0A-005
VTEC valve to cylinder head gasket: 15825-P0A-015
VTEC oil pressure switch o-ring: 91319-PR3-003
Thermostat housing to intake gasket: 91312-P0A-000
Thermostat housing to connecting pipe o-ring: 91314-PH7-003
These part numbers should work on all 1994-1997 Accords with VTEC but as
always check with your dealer to confirm these part numbers will work with
Intro and outro music Hot Swing by Kevin Macleod (Incompetech.com).
Due to factors beyond the control of Bushougoma, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. Bushougoma assumes no liability for property damage or
injury incurred as a result of any of the information contained in this
video. Bushougoma recommends safe practices when working with the tools or
equipment seen or implied in this video. No information contained in this
video shall create any express or implied warranty or guarantee of any
particular result. Any injury, damage or loss that may result from improper
use of these tools, equipment, or the information contained in this video
is the sole responsibility of the user and not Bushougoma.