20B ROTARY ACTION! 20B DATSUN 1200 & 20B MAZDA RX3 - TNT 28/12/2013
On the final Test and tune at Willowbank Raceway for the year, Brad Mcilroy
was out testing his Mazfix prepped 20b Datsun 1200 ute as well as Russ in
his 20B powered Mazda Rx3. The PRODAT was testing some changes in the rear
end, keeping the newly added 10.5 inch tyres as well as some changes to the
4 link, and after a few tweaks had the car complete a full pass of 7.95 @
165 mph with a small back off down the deep end, a little slower then what
the car has run but a little more stable down the track. The Mazda Rx3 had
some issues most of the night but managed to get it down the track for an 8
second pass, also off its best, but once sorted should be back down to
where it was running before.
WORLDS FASTEST ROTARY 6.58@208 MPH
When are these guys going to stop breaking the records?? every time pac
performance goes out to the track, they put on a HUGE SHOW, a job well done
to George for steering the Pac Mazda 6 to all new hieghts more info coming
soon to http://www.rotorg33k.com
Part 12: 13B Rotary Engine Rebuild - My 76 Mazda RX-5 Cosmo Restoration
Just as I promised last episode, it is finally time to build the engine!
Part 12 of my RX-5 Cosmo restoration covers the entire process of building
the 6 port 13B Mazda rotary engine. While this engine is a hybrid of GSL-SE
RX-7 and Cosmo parts, the process is the same for any rotary from a 12A to
a 13B NA, 13B turbo, 13B-REW or any
other variant of the 13B. This video shows the whole process of the engine
build, starting from measuring the rotors and covering everything else
including clearancing the side seals, assembling the rotors, complete
assembly the short block, setting the eccentric shaft end play and
installing the front cover and everything underneath it. It's probably the
most complete engine build video outside of what you can buy from the
vendors, and as such, is an hour long. After this one, I'm going back to
videos under 20 minutes. But for now, grab a beverage of your choice, sit
back, and enjoy.
SCREAMING 20B rotary engine dyno ~ JPC
Centreline Suspension's 20B PP rotary engine from their Mazda RX-7 Sports
Sedan circuit racer on the Dyno at JPC.
20B turbo Mazda RX-7 - Promaz
Charles' Promaz modified FD RX-7 racing for the first time. The car
features a second-hand import 20B triple rotary engine, Garrett GTX42R turbo on 12psi Boost, MicroTech LX12 computer running on
98-octane unleaded. The driveline is still factory RX-7 issue.
Hi Octane R100 Highlights - 13b Rotary Dragster - V 4&Rotary Nationals 2012
Find Us On Facebook,
Graham Prior's well presented Methanol Fueled, 13b turbo Powered R100 Dragster, Driven by Craig
Dyson. Highlights from the HiOctane racing during the 'Aussie Invasion' as
part of the V 4&Rotary Nationals held at Fram Autolite Dragway, Meremere,
Highlights Video thanks to Hi Octane Performance Coatings
Checkout Hi Octane Racing,
Filmed & Edited By Kenny Ruddell
Produced By SBPnz
Checkout our website,
WORLDS FASTEST AWD / 4G63 DATSUN / 20B RX7 IN TESTING
Willowbank Raceway held the 1st of the 2012 Top Sportman Series on the
weekend. Reece McGregor and the Heat Treatments Skyline thought it would be
a good chance to have some test runs in their worlds fastest RB26 powered
4wd skyline. The team worked hard all day and were rewarded with a final
pass or 7.64, not far off their 7.56 record, although something tells me
theres plenty more to come from this car again.
Another car using the test lane was Rob Novak in his Jett Racing 4G63
powered Datsun 1200. The team made adjustments through the day and saw a PB
7.35 @ 187mph on the second last pass of the night, the final wild pass on
video then saw a transmission failure but a happy team none the less.
Final team testing was the Direct Clutch/Promodz Rx7, the car is 3/4
chassis and a running 3rotor 20BT tweaked by Mazfix. The team recently made
adjustments in the rear and also in transmission and are starting to see
results, it ran a 7.99 @ 171mph through the day, then later in the night
suffered a leaking Boost pipe.
Owners Jerry and Dan tell me they havent even started to push the motor
yet, so another car with plenty more to come, and im sure that pb 7.80 will
soon be slashed.
These cars should all be running at the up and coming Sydney Jamboree at
WSID and by the looks of things have some unfinished business they want to
take care of :)