Fitting the pistons, camshaft & oil pump in a 1275 A+ block
In this video how-to, Mini Mania's engine tech Tony Gambirasi, explains the
proper way to install piston rings, pistons, the camshaft and lifters, and
the oil pump in a 1275cc A+ engine block.
Connect with Mini Mania:
Google +: http://plus.google.com/109690635628067357029/posts
Or give us a call today toll free at (800) 946-2642
1963 Falcon Futura.wmv
1963 Ford Falcon
Red Bucket Seat Interior
Fresh 302 V8
Boss Throttle Body Fuel Injection
T5 5 Speed Transmission
8" Rear End (4:11)
Mustang 2 Fr9ont Suspension
Alpine Stereo System
Chrome Reverse Wheel
Nostalgic Red Steering Wheel
Very Cool Car
check it out at
Classical Gas Enterprises
"There's A Future
In The Past
BMW E36 E34 camshaft & lifter removal and installation
http://www.mybimmerspace.com In this new video, I remove and then
re-install the camshafts with a new set of INA lifters on a BMW E36 with a
M50tu engine. For those of you, who have been following my videos: I start
the camshaft removal process after I removed the upper tensioner & chain
guide which you can see at the end of my other video "BMW E36 Vanos &
tensioners removal" part 1. Thank you for all of your support
Installing a Ford Synchronizer
Ford Camshaft synchronizer's are a common failure. Some techs aren't
familiar with them so they may not be comfortable with them. Unfortunately
the service manuals aren't very clear in describing the install process.
I've made this video to help you understand them, and show how to properly
1972 chevy vega 427bbc
my vega i am building it have a full studded 427 big block with 11.5 to 1
pop ups, forged crank, closed chamber heads, roller rockers, gear drive
timing, big mother thumper cam, tunnel ram and two 660 holly carb. It hase
the hooker motor mount and trans mounts and hooker super comp headers.
trans is a built 350 with 3500 stall. car is back half with a nine nich
ford rear. is a work in progess and will post more as i do more to it.
Dad's Chevy Big Block 402
Street/Strip Chevy Big Block 396. Full Roller. Hydraulic Big Mutha Thumpr
Comp Cam. 9.5 Compression. Balanced and Blueprinted. horsepower: PLENTY!!!!!
This baby rat will run with most street big rats.
Removal and Inspection of A Camshaft and Lifters
This is just another video of tearing down the motor in the 2003 Jeep TJ
with a 4.0L engine. in order to remove the camshaft you need to remove the
timing chain and gears which i showed you how in a previous video. the
camshaft is only held in place by 2 torx screws after you remove them the
camshaft you can pull right out.
the camshaft lobe itself was worn down on the opposite side of the push
rod that broke. the lifter that was in the broken hole was dented and
Quick Tech Video: How to Degree Your COMP Cams® Camshaft
Installing a new camshaft often requires degreeing. This Quick Tech how-to
video from COMP Cams® is a step-by-step walkthrough on how to degree your
new COMP Cams® camshaft. But the Powerhouse® Products Cam Degree Kit can
be used with any brand of camshaft.
VW TDI and Audi TDI bad camshaft removal and replacement procedure DIY
How to replace VW TDI camshaft and Audi TDI camshaft, please read:
place-vw-tdi.htm for detailed instructions and sign up to my site. Pumpe
duse PD camshafts tend, to wear, needing repair and replacement of lifters
and bearings before engine wear occurs.
Sema 2010 Fins Customs Ford Falcon
Hope you like our new video of our custom half done 65 Ford Falcon. Done by
our shop, Fins Customs & Classics in Turlock, CA. We did this project to
advertise our shop. We carried the theme through the whole car ever the
underbody. Danny at Prime Time Interiors in Turlock took care of the
interior doing a great job of sewing the new and old together. The sound
system was sponsored by Arc Audio with an ipod providing the music.