Proton Turn Signal Flush Mounts for Yamaha FZ6R - How-To Installation
Proton Turn Signal Flush Mounts for Yamaha FZ6R - How-To Installation
Yamaha CustomLED Connector Proton Flush Mount
Black - Black - Black
Blue - Red - Red
Brown/Green - White - Yellow/Orange
Proton Flush Mounts:
http://www.hightechspeed.com/products/ProtonLights/index.asp
Proton Flush Mount instructions:
http://www.hightechspeed.com/products/ProtonLights/instructions_lg.gif
Custom LED Yamaha Front Turn Signal Plug and Play Connector:
http://www.customled.com/products/oem_connector/oem_connector.htm
Flasher Relay Install:
http://www.youtube.com/watch?v=7mwW4zE0dCw
You can also take a look at my first impressions of the Proton turn signals here:
http://www.youtube.com/watch?v=OhiLVmTARXM
2006 Yamaha R6 w/ LED halo turn signal
I didn't care for my Audi inspired turn signals, so I tried something different. I got new blue halos that are thinner and have longer wires with only one ballast instead of a ballast per halo. Then I installed LED halo under the Blue halos to act as my new turn signals. During the day they aren't spectacular, but nor are flushies.
2009 Yamaha YZF-R1 - Frame/Clutch Sliders, Turn Signals Install Howto
This is an instructional overview of the installation of No-cut Frame Sliders, Clutch Slider, and Flushmount plug-and-play turn signals on a 2009 Yamaha YZF-R1 motorcycle.
I both narrated and shot the video, so please excuse the missing parts where I tightened the bolts.
Sliders from Graves - www.gravesport.com
Flushmount Signals from Lockhart Phillips - www.lockhartphillips.com
Yamaha R6 Projector Headlights BiXenon hid Angel Eyes Halo By BKMOTO.com projectors 2006 +
These 2006 - 2011 Yamaha R6 headlights were custom retrofitted with our BiXenon Projectors, Dual Halo's, Red front halo and White rear halo, as well as headlights blackout. We offer custom installations and retrofits, mail us your headlights, let us know how you want them, we'll work our magic and return your headlight completely Plug and Play. contact us http://www.bkmoto.com complete DIY kits are available on our website as well. http://www.bkmoto.com
Available for Yamaha R6 years 2006 2007 2008 2009 2010 2011 2012
2006 2007 Yamaha R6 Flushmount Signals Installation DIY
Installation procedure of a TST Industries Flushmount Signal Kit for a 2006-2007 Yamaha R6
Available for $12.99 at www.TSTindustries.com
Check out TSTindustries.com for more information
yamaha r6 led lights audi light strip
just installed some lights on my r6 audi light strip up front and blue led lights around the motor and the red led light up front in the middle
03-05 R6 06-09 R6s Clutch How-To (diy)
DIY: How to replace the Clutch on a R6
03 - 05 R6
06 - 09 R6s
Done with OEM Parts (same procedure with aftermarket parts)
- (6) Friction Plates: 4FN-16321-00-00 (red color reference tab)
- (2) Friction Plates: 5SL-16321-00-00 (purple color reference tab)
- (7) Pressure Plates: 3J2-16324-00-00
- (1) Pressure Plate: 168-16324-00-00 (thicker than the other 6)
- (6) Clutch Springs: 90501-237L0-00
- Clutch Cover Gasket: 5SL-15461-01-00
Torque reference:
-Pressure Plate Bolts 10mm: 5.8 ft.lbs (8 Nm)
-Clutch Cover Bolts & Cable Bracket Bolts 5mm Hex: 8.7 ft.lbs (12 Nm)
****Important notes****
-Soak the Friction Plates in Fresh Oil for at least a half hour before installing them.
-Do not remove the coolant hose unless you plan on draining the coolant prior.
-Clean off old gasket material (use a razor blade if needed)
-Line the Dot on the pressure plate up with the small Dot on the Clutch Basket
-Arrow on the Clutch Cover (above the shaft arm) should line up with the marking on the arm when the arm is pushed forward by hand (until it stops).
-Some people say you need to drain the oil. Oil was not drained before this install, if the bike has been sitting for a day or 2 it should not make a mess of oil.
Video does not include how to remove/install the Lower Left Faring (if you can't manage that on your own you shouldn't attempt to do the clutch)
Disclaimer: I assume no responsibility for you performing this work on your motorcycle.
Watsen flush mounts
Watsen LED flush mount turn signals installed on a 2008 Yamaha R6. Colour code varies on the year of the bike. For 2008 it should be gloss black.
Install was easy. Keep in mind these, when installed, disable the running lights for the front signals.
03-05 R6 & 06-09 R6S Changing display settings (shift light)
How to change the settings on the gauge cluster on your YZF R6/R6S motorcycle such as the shift light brightness, timing when it comes on, and the clock. Very annoying when the shift light comes on at 13K per the stock settings and blinds you at night.
ResArt Yamaha R1 2009 Fender Eliminator with free plate light. Available @ www.resart.com.au
HI
This is a ResArt Yamaha R1 2009 Fender eliminator install and the installation process is the similar as the R1 2004 up. You can go to our web site for more bikes and our range. If you have any querries you can contact me on sales@resart.com.au or via www.resart.com.au
Cheers
2008 Yamaha R6 start up and walk around
this is a 2008 yamaha r6 with 2800 miles a two brothers Exhaust.. flush mount turn signals and the smoked hotbodies integrated taillights. this bike is for sale.. i'm selling it because i already have a 06 GSXR and i love that bike to much to let it go.
R6 LED FINISH
THE FINISHING TOUCH IS DONE WITH CHECK IT OUT AND COMMENT THANKS
