How To Pull Honda Codes Without a Scanner -EricTheCarGuy
Link to code explanations:
Honda ABS Codes 1994-1997:
Honda ABS Codes 1998 and up:
Visit me at: http://www.ericthecarguy.com/
Discussion about this Video:
I feel like I should have made this video a while ago but the opportunity
never came up. Since I had this RL in my shop that had a check engine
light AND an ABS light I thought it was a perfect opportunity to put this
video together. I get asked all the time about my 'special tool' and it's
really nothing more than a Honda 2 pin connector with the input wires
soldered together. These connectors might be harder to find than you think
but if you run across a junk honda and one of these is on the harness grab
it. Even if you don't have the tool a paper clip or piece of wire will do
the exact same thing so don't sweat it if you don't have the tool because
shorting the connector is all you need to do.
I hope you find this video helpful.
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
AFAccord's F23 Turbo Accord - HD Vids and Dyno
I only had a week to drive the car after it was tuned and wasn't able to
wire up my ECU switch in time to get any high Boost runs on video. Sorry guys! I'll make
plenty of high-Boost videos when I
come home, so subscribe!
Music rights belong to Gemini - Graduation of AEI Media.
Parts and Specs:
-F23 block, bored to 86.5mm
-Wiseco K20 spec pistons @ 10.5:1 compression
-SwainTech ceramic coating on piston crowns
-Crower F23 rods
-OEM main bearings (pink across all journals)
-ACL HX rod bearings
-Kaizenspeed balance shaft delete kit
-Bisimoto heat-shielding intake manifold gasket
-Bisimoto Pro valve springs
-Bisimoto Pro valve retainers
-Bisimoto cam gear
-Innovative 65A engine mounts
-Maxbore F23 throttle body
-MFactory limited slip differential
-DIY ramhorn turbo manifold
-DIY 2.5" charge piping from CXRacing
-28"x8"x3.5" FMIC from Go-Autoworks
-Triple-core half-size radiator from Go-Autoworks
-3" Straight pipe Exhaust
-3" Vibrant Flat black muffler
-Garrett T3/T4 57 trim turbo
-ACT Xtreme pressure plate
-ACT Streetlite flywheel
-ACT performance street disc
-Tial 38mm wastegate
-Tial Q BOV
-P61 OBD1 ECU
-Tuned using eCtune by the infamous... Joseph Davis!
heres a video of my k24a4 turbo TSX Boosting 16lbs on a stock motor. data
logging a 3rd gear pull so i can adjust my air/fuel.
701hp S2000 From Hell-Part1
701whp S2000 tuned and built by T1 Race Development. Car has bone stock
motor, tranny, and rear end.
***S2K never saw the 701whp in this video, highest hp was around 600whp
against the GSXR1000***
All you haters that think its not really pushing out 701whp heres the Dyno video...faggots
and the music is kanye west 808s and heartbreaks and linkin park, no more
Malkolm @ Test and Tune
Malkolm testing the Accord on Malmby Fairground 2010 07 17.
best time 13.11 @ 174km/h
And i quote Malkolm
"1st gear only 2psi of Boost
2nd gear only 4psi
then it hits 11psi!
Peakb00st baby! peakb00st!"