Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

1982 Chevy S-10 406 SBC

Gettin the drag truck ready for the 2010 drag racing season. By the way the line lock still works haha


 


More Videos...


Built Chevy 406 S-10 on Dyno
CHRIS VAN LOON'S 89 S10 WITH A BUILT 406 AND A SLIPPING TH400





BRODYS S10 406 CI
just put in the new 406 only ran 8.20 pulling it out for pinks all out got to go faster :)......





The Beast 406 ci. S-10
1982 chevy s-1o 400ci., bored .30,over Flat top piston,forged internals,292 comp. cam, 441 heads,port and polished,alum. intake,650 edlbrk.carb,more.... http://community.webshots.com/user/Carkrazy12 Check out my Cars....!!!





Dad's S-10 w/ 406
Just sittin in the driveway...





s10 drag racing runs 7's
taking truck to the track runs 7.07 @97 1.60 60ft





Short box chevy 11in lift 38's 406 sbc donuts
Dalton's short box short clip at 7mile on fathers day 2010





406 Chevy Running on Test Stand
Testing my 406 Chevy motor





malibu del chino montes en la pista de tucson az junio del 2010
el aaron en el carro de montes en la gambler races del evento fuel altered nationals. 406 sbc on pump gas





84 s10 406 v8
S-10 with the 406 idleing.





MY PRO STREET 62 CHEVY NOVA
12.5 to 1 406 sbc 456 gears 5500 stall powerglide transbrake / delay box tubbed out etc etc.





Chevy S10 1982 - 2004
The history of the Chevy S10 .





406 SBC Omega
74 olds omega, pump gas, foot brake, woodburn dragstrip Mighty Demon 750 Carburetor, Spectre Ram Air kit, Edelbrock Victor JR. Intake, MSD Pro Billet Distributor, MSD 6AL, MSD Blaster coil, 8.8mm Taylor Plug wires, Comp Cams Aluminum Valve Covers, Comp Pro Magnum Rocker Arms 7/16 studs, Trick Flow 1 piece push rods, Air Flow Research 210 Eliminator Heads 65cc 11.44:1 with flat top pistons and .0038 felpro performance head gasket, Comp Cam XR294HR Hydraulic Roller Cam and Lifters, 2 Piece timing cover, SRP Forged Aluminum 2 valve relief pistons .030 over, Total Seal Rings, Scat Forged 4340 steel I beam rods w/arp bolts, Scat Forged 4340 Forged Steel Crank, ARP Main Studs (4 bolt main), ARP Head Studs, Clevite Tri-armor Coated Main and Cam Bearings, Standard Pressure High Volume Oil Pump (Big Block pump), Motor is a 4 Bolt main, 2 piece rear main seal, internally balanced, 7qt oil pan with trap doors for oil control. Summit SFI approved Harmonic Balancer, SFI approved flex plate, newer stock SBC starter, 90 amp new chevy alternator, proform electric water pump, March billet aluminum alternator mount (mid mount passenger side), 1 7/8 hedman





406 Small Block Chevy Dyno Run
My Small Block Chevy 406 on the Dyno at A&J Automotive after being rebuilt. Four separate runs after jet changes & some fine tuning. 466Hp/485ft/lbs





BG Engines Blown 406 SBC
BG Engines 406 Blown Small Block Chev makes 940hp at 7000rpm using 9lb Boost





My new Black 55 doing a burn out on slicks 406 sbc
Just a clip of my new 55 doing a burn out, by my garage just after i got back from the track,,, still had slicks and open Exhaust on it,, Ran 11.81 that day!!!




Which car is faster? Which Car is Faster?





Similar 1/4 mile timeslips to browse:

1964 Chevrolet Chevy 2: 10.610 @ 117.000
, Engine: 355, Tires: firestone


1991 Chevrolet Chevy S10: 11.526 @ 115.370
Jason Miller, Engine: 350, Tires: micky thomson 32-14.5-15


2005 Chevrolet Chevy Corvette C6: 12.557 @ 110.860
James, Engine: LS2, Tires: Stock non Z51 run flats


1955 Chevrolet Chevy : 12.720 @ 109.500
Ken Abbott, Engine: 454 Chevy, Tires: 28.5 Slicks on rear


 


©2014 DragTimes - Disclaimer