We used a Dart Block completly machined by www.mesabalancing.com the cylinder heads were hand ported along with the intake and we tailored the ignition curve and carburator on the Dyno using sunoco 112 fuel.
572 Cu In Streetable Big Block With 750HP
Live engine run of a Chevy 572 big block...engine will be run in a '66
Chevy Chevelle...Proformance Unlimited...There is no other
Our staff is available to assist you with any questions you may have
Monday-Friday 8am-5pm 800-267-3940 or via email
We look forward to speaking with you.
Chevy 383 Stroker 650 hp
First time cranking the beast.AND THIS CARB WAS SHIT SO I REPLACED IT I WAS
ONLY USING TO TEST AND TUNE WHILE ON THE STAND- Engine Contents:
BRAND NEW DART 4 BOLT MAIN BLOCK
Heads - Dart Pro 1 Aluminum series CNC PORTED 320 CFM
Carburetor - QUICK FUEL Q-950 RACE SERIES CARBURETOR
Distributor - COMPLETE MSD DISTRIBUTOR SYSTEM WITH AL6 BOX AND COIL with 3
step and crank trigger
Hooker Super comp headers Ceramic coated
Intake Manifold -Team-G High rise intake CNC port matched
Fuel Pump - 400 GPH HIGH VOLUME Holley
Water Pump - CSR electric
Valve Covers - CUSTOM Chevy engraved and clear coated
Wires - MSD PERFORMANCE WIRES
Spark Plugs - NGK PERFORMANCE
Forged Pistons -J&E FULLY FORGED PISTONS
Forged Rods -Manley Push Rods
Crankshaft - Callies Magnum 4340 FORGED 3.75" STROKE CRANKSHAFT
Rod Bolts - ARP
Roller Camshaft - COMP CAMS ROLLER CAM
Valve Springs -Manley Nex Tek Triple Valve Springs w/ Titanium Retainers
Hydraulic Roller Lifters - COMP CAMS ROLLER LIFTERS
Double Roller Timing Set - PRECISION TRUE ROLLER
Timing Cover - CHROME GM PERFORMANCE BOWTIE
Head Bolts - ARP stainless
Flexplate - SFI PRECISION
Harmonic Balancer - ATI Performance Products SFI Rated Balancer
1966 Nova SS - 8 second street car
Back half pro street car from upstate NY.
Best ET = 8.68 @ 156 1/4 mi. / 5.55 @ 126 1/8 mi.
Zero to 60 MPH in less than 2.5 seconds.
Approximately 950 flywheel horsepower through the
Mickey Thompson 13 x 31 ET Street Tires.
Dynomax 3" welded race
434 small block by Chris Yates.
TH400 full manual trans w/ ATI 9" converter.
Dana 60 w/ 4.10 gears and ladder bars.
Street driven. (Plates removed to protect the guilty!)
Chevy Crate Engine 427 SBC 550HP
427 Small Block Chevy Crate Engine With 550HP. Built By Proformance
Unlimited...the one and only http://www.proformanceunlimited.com
For More Information Visit Our Web Site Or Call 1-800-267-3940.
how to build 383 stroker,first start 383,383 dyno,caponeauto
BLOCK:blue printed,decked square to factory 9 inch height,line honed,bored
and honed .030 over with deck plates,holes chaced and champherd,new cam
bearings,brass frost plugs,new dowl pins.
ROTATING:scat 500hp ballanced 6"rotating kit.(was reballanced..I always
check.it was fine).
PISTONS:hyp claimer .030 over,flat top 2 valve relief,floating pin
RINGS..030 molly filled top ring,std tension oil ring
RODS: I beam 6" floating pin,ARP cap screws,weight matched
BEAGINGS:std size p bearing
CAM:comp cams(of corse) xtreme 274 hyd roller
HEADS:procomp 210 runner,64cc combustion chamber,cnc chambers.ARP 3/8 screw
in studs.pro comp adj guide plates
HEAD BOLTS: arp
ROCKERS: comp cams pro mag 1.5
INTAKE procomp dual plane air gap.
HEADERS:hooker super comp ceram coated,large long tube .gasket matched to
heads(took almost whole day to oppen em up ..lot of grinding and welding)
CARB:holley 750 dbl pumper w/4 corner idle.stock jetting and power valve
6.5.switched to quick fuel 750 jetted down...to the holley specks
DIST:msd hei 'plug n play' adj vaccume advance. 36deg total...8deg at idle
426HP 398FT LBS on PUMP gas
The Ultimate Small Block Stroker Engine Build -- Part 4
The fourth video in a series building a big inch stroker motor. We're
cramming 427 cubic inches into a small block Chevy with all off-the-shelf
parts. This time we're installing the valve train, intake and and ignition.
For the rest of the videos in the series, build sheets and even Dyno results, check out
ltimate-stroker/ . Thanks
We're constantly uploading great new videos. Please subscribe so you won't
MORE INTERNET GOODNESS:
Come get SCHOOL'ED 1966 Chevy Step Side Mud Dragster
San Antonio Mud Drags Please feel free to check out the website for
upcoming events and pictures.
Gotta say this is one of my fav's at the track. Just the old school look,
and still rolling on leaf spring's. And powered by a small block chevy.
Check it out and leave a comment and rate, let me know what you think.
keep on rockin
Skull Crusher Adventures
rockin TEXAS style