Saturn Idle problem.mov
In this video we show you how to replace an idle air control solenoid and
clean the throttle body on a 1996 Saturn. This car was having a
excessively high idle. It would stay at 1500 RPM even though your foot was
not on the gas pedal. This was caused by carbon build up around and behind
the throttle body as well as a defective idle air control solenoid.
Jonesy's Auto Club videos are for reference and entertainment only and
should not be taken as a direct step by step guides. If you attempt a
repair like the one seen in this video please use the proper safety
equipment, take your time and do the job right.
Pimped Out Saturn SL2 *UPDATED*
NEW: just got a body kit! its installed but has a few fitment issues that
need figured out. looks sweet, but needs some work before its done!
also did the "Flip Flop" trunk mod, took out some of the carpet, cleaned
things up. always messin around with this thing
check out my page: http://www.cardomain.com/id/courtlife
*NEW 18" Konig Uknowns with Kumho spt tires (for the summer)
*removed the bar across the "grill" and the front license plate - looks
*swapped the subs and Tv's because of trunk rattle & tailgating purposes
*Redone carpet in the trunk/back of the back seats
*Black Saturn Emblem
*Sony Door Speakers
*Saturn Racing Team decal on windshield
*Painted Calipers and Drums black
*Repainted the dash Silver
*Painted the molding above the windows black
*Weapon-R cold air intake
*Chrome Exhaust tip
*Switches installed on dash for Amp and power inverter for PS2 & tv's
*2 12 inch Type R
*Q-Logic Ported/Sealed Box
*2 15 inch Sony TV's
*Power Acoustic PTID-6500
*150 Watt PA System (Speaker is OUTSIDE)
*Blacked-Out Taillights and Side markers
*Sony Playstation 2 in the trunk
*5 % tint
*Bulldog 200 Deluxe Remote Start
All installation was done by myself, including remote start and tint job.
Any questions or comments are appreciated!
Saturn SL2 Valve Cover Gasket Replacement (DOHC)
This is a long one, Sorry, but it pretty much goes through the step by step
and shows some of my mistakes so you don't make them.
Also, verify that the gasket fits. If you have the time then I would
suggest bringing the valve cover in with you(assuming you bought it from a
local parts store) and make sure it fits before leaving. I must have gotten
one from a bad batch because the first one was too big. You will see that
in the video. The second try was the right(ish) one. apparently it is a
known problem that the molding process is incorrect for these gaskets but
luckily they are rubber so you can just remold it to fit.
Also a word of caution: at some point you may see me use carburetor cleaner
on the plastic valve cover. DO NOT use carburetor cleaner on the plastic.
The main ingredient is Acetone(which I also use to clean) and it has the
ability to melt the plastic. Use another solvent that is friendly to
plastics like mineral spirits.
Good Luck and Hope this helps you save some money. Spent about $60 total
doing this in tools and parts.
Note: I am not a mechanic, these videos are meant to be for informational
purposes only. Should you follow the steps shown you do so at your own
Super Wagon Drag Race! Cadillac CTS-V vs Mercedes-Benz E63 AMG - Head 2 Head Episode 4
On this episode of Head 2 Head, Jonny Lieberman pits the supercharged 2011
Cadillac CTS-V Sport Wagon against the twin-turbo 2012 Mercedes-Benz E63 AMG Wagon. Witness
the mother of all mommy-mobile matchups, capped off with a 150MPH half-mile
Read the full story here:
Head 2 Head appears every other Wednesday on the new Motor Trend channel.
Subscribe now to make sure you're in on all the action!
Facebook - http://facebook.com/motortrendmag
Twitter - http://twitter.com/motortrend
Google+ - https://plus.google.com/101867967859016552744/posts
Website - http://www.motortrend.com