Becky Accord new Wheels test Fitment 2013 PART 2 of 2
I had an issue making my new wheels to fit perfectly on becky, so i thought
of an idea which is swapping the faces from front to back/back to front.
Front faces are meant for BBK clearance so by swapping them i can change
the offsets of the wheels. :)
How to Change a Wheel Bearing (short and fast version)
This video shows how to change a pressed bearing in a Ford, specifically a
95 Ford Windstar, but this method will be similar for all pressed bearing
vehicles. The main steps are to take off the spindle nut, tire, brake
caliper, and rotor. Then remove the bolts from the lower control arm ball
joint, tie rod, and strut. Remove the steering knuckle, then press out the
bearing and hub/spindle. Then press in your new bearing and hub/spindle.
This job is a little more complex but can still be easily done by any
amateur mechanic. You will save $400-800 depending on your vehicle. Pleas
comment, like and subscribe if you liked this video!
how to remove a pressed front bearing, how to remove a front bearing, 2003
Mazda Front Wheel Bearing Replacement (Press In Type Bearing), How To
Remove Pressed-on Bearings - EricTheCarGuy, Wheel Bearing Removal with
Harbor Freight Universal Tool BMW 325i Rear Front, bearing, press, pressed,
pressed bearing, front bearing, front wheel bearing, diagnose, how to, diy,
ford, windstar, ford windstar, Pressing out a front wheel bearing, harbor
freight, bearing kit, How to: Remove & Install A Truck Hub Bearing Assembly
with Timken, How to remove a rusted wheel hub bearing assembly the easy
way, trick, mazda, ford, lincoln, gm, truck, van, car
Due to factors beyond the control of ChrisFix, it cannot guarantee against
unauthorized modifications of this information, or improper use of this
information. ChrisFix assumes no liability for property damage or injury
incurred as a result of any of the information contained in this video.
ChrisFix recommends safe practices when working with power tools,
automotive lifts, lifting tools, jack stands, electrical equipment, blunt
instruments, chemicals, lubricants, or any other tools or equipment seen or
implied in this video. Due to factors beyond the control of ChrisFix, no
information contained in this video shall create any express or implied
warranty or guarantee of any particular result. Any injury, damage or loss
that may result from improper use of these tools, equipment, or the
information contained in this video is the sole responsibility of the user
and not ChrisFix.
Replacing an Accord Wheel Bearing - EricTheCarGuy
Replacing an Accord Wheel Bearing
Ok, here it is finally. A few of you have requested this procedure so here
it is. As I said in the video I normally use a different method of
removing the hub from the bearing assembly by using a slide hammer. I also
normally use a press to reinstall the hub into the new bearing instead of
hitting it with a hammer. Life is not perfect and we sometimes have to
improvise as I did here. I know a few of you will ask about the size
fasteners that I used to hammer the bearing out, I used hardened (8.8)
10x1.25 bolts to do the job. I also promised links to the other videos
that relate to this one so here they are.
"Oops, Axle Ball Joint Replacement"
and also "How to Replace Honda Captive Rotors"
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
Visit my Facebook Page:
Thanks again to all that have subscribed and left such great comments on my
videos and my channel, you are the best, I mean it.
You know the line
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
2011 Honda Accord Crosstour Video Review
FOR PRICING & SPECS ON THIS CAR VISIT:
With enhanced cargo-capacity, a raised driving position and optional
all-wheel drive the Accord Crosstour is one of a growing number of vehicles
that blur the line between car and SUV.
2011 Honda Accord Crosstour 4WD EX-L Start Up, Engine, and In Depth Tour
In this video I give a full in depth tour of the 2011 Honda Accord
Crosstour. I take viewers on a close look through the interior and exterior
of this car while showing details, over viewing of features, and noting
unique styling cues to the vehicle itself. I also show the engine and the
details of it, start it up and see how it sounds under acceleration. A
thorough tour/review of this car designed to give others a greater overall
appreciation of the vehicle.
RYNO Motors Full Story
This is a great story on the early days of RYNO Motors. See our latest
creation pre-production show bike at our web-site and pre-order at
http://rynomotors.com/store and don't forget to buy a Tee Shirt:
2011 Honda Accord Crosstour
Call 1-800-488-4333 or visit http://www.carmichaelhonda.com to test drive
this vehicle today. We are also the #1 Parts and Accessory dealer in the
nation! Go to http://www.handa.com for a complete list of products.
Our dealership is located at 6151 Auburn Boulevard, Citrus Heights, CA
1995 Honda Accord Rotor and Wheel Bearing Replacement (Trapped Rotor)
Shows how a trapped rotor fits together on a 1995 Honda Accord. You'll
need a press to replace the brake rotor and wheel bearing on your 5th
Generation 1994-1997 Honda Accord. Shows how the hub, wheel bearing and
brake rotor fit on the knuckle.
Do this repair yourself and save a ton of money. Instead of buying a
press, I got a membership at ClubWorkshop.com (Denver Colorado) where they
have a 50-ton press. A 50-ton press is probably overkill, I've heard a
20-ton press (or smaller?) will do the trick. Be very careful using the
press, the extreme pressure can cause objects to shoot out as projectiles.
I'm sorry I don't have video of using the press, but you can find other
videos that show you how to use a press.
Jessica test drives the 2009 Honda Accord EX-L ( Part 2 of 3)
After speaking with Brandon about which Honda would best suit Jessica's
needs, she takes the 2009 Honda Accord EX-L out for a test drive.
Brandon explains to Jessica all the features to be found in the Accord EX-L
and Jessica tells Brandon what she thinks of the handling and the overall