2005-2011 Toyota Tacoma Bull Bar Installation
Putting a bull bar on my 2006 Toyota Tacoma TRD Off Road 4x4.
I couldn't find any other videos on how to do it so I thought I would make
one, Hope it's helpful.
And sorry for changing names of parts, i was in a rush.
Westin Tube Step Installation - 2008 Dodge Ram - etrailer.com
Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.
Today we are going to install E-Series Tube Steps from Westin, part number
23-2900, and we are going to install this on a 2008 Dodge Ram pickup crew
cab. The body brackets will actually mount to the body bolts right here -
one at the front of the cab here, and we are looking underneath the
passengers side of the vehicle - and then the last one at the back of the
vehicle, this one right here, it mounts up there. The bolts in the centers
come out, and they get replaced by new bolts that come with the kit. Okay,
we will start off with the rear passenger body bolt. Then we will take a
bracket and our hardware and run a bolt right through and thread it into
place. We are just going to snug them down for now, and we will tighten up
everything as our last step. The front bracket actually gets a spacer on
top, and the long bolt goes through just like before.
All right, next we will attach our center bracket. And what is going to
happen is we are going to use the center hole, here - not the slot, but the
center hole. You have to be able to get this T-bolt inside. And there is a
hole right behind the sticker, so we have to pull off the sticker, put the
T-bolt into it and out the hole, and then put our center bracket into
place. Make sure the bracket fits along the body panel like this. Again, we
will leave everything loose and then we will readjust it when we put the
tube on. All right, next we are going to install our bracket that goes from
the frame to the bracket right here. It is going to fit just like this.
Then we will install hardware in the frame, also. And this bolt right here
with the block welded to it will simply fit inside with a twist, and then
we can attach our hardware. Install the bolt with the thin washers, then
the lock washer and the nut.
At this point we can install the tube steps onto the brackets that go to
the body mounts. So, let us just hold it up in the air and start threading
them in. All right, next we will do the center bracket right here. And we
left the tube loose so we can move this around and get our center bracket
lined up. We will run our flat washer, lock washer and bolt and just thread
it into place. And with that, we can start snugging down all the bolts. All
right, once you get those bolts torqued down, go ahead and hand tighten the
rest of the bolts that go to the body and the brackets and to the step
itself. Then you can go ahead and repeat all these same steps on the other
side of the vehicle. So that covers it for our install of part number
23-2900 from Westin.
Oval Nerf Bars | Raptor Series Installation
Free Shipping at
Oval Side Steps
4" oval step pad width Our 4in oval tubes have grown in popularity and
expanded to over 50 applications. These bars also feature the new full 4in
raised saddle style step pad with the Raptor Series logo in the middle.
5" oval step pad width Raptor Series is proud to introduce the next
generation of Oval Tubes. Similar to it's predecessor the new MAGNUM OVALS
are available with an amazing 5" extra wide saddle style step pad for
better footing. These monster stainless steel tubes come with ultra
polished stainless end caps and are backed by Raptor's superior Lifetime
To view our entire selection of Nerf Bars visit
cop ramming the jeep part 2
cop pushing the jeep off the road
the track bar broke while we were rounding the corner. since the front axle
was then free to move side to side, we basically lost steering. hitting the
Toyota Tundra (5.7L) Cabin Air Filter How To Inspect / Change
How to change the cabin air filter in a Toyota Tundra (2008 Model shown)
Toyota really made it easy to change the cabin air filter on the new
Tundra. The cabin air filter cleans the air that you breathe and also
keeps contaminants like leaves, bugs, dirt, etc. from getting into the
blower motor. If you cab smells funny when you turn on the fan, you might
have a cabin air filter that is plugged up with stuff and maybe even some
rotting material stuck in it. quick and easy to remove and replace.
Install Westin Ultimate Bull Bar - AutoAnything How-To
Buy the Westin Ultimate Bull Bar:
Westin's Ulitmate Bull Bar a great addition to any truck. Built from solid
steel, this push bar can stand the test of time.
Installation is simple, just bolt it on using the included hardware and
you're good to go.
Want something a little different? We have a huge selection of bull bars:
... and Grille Guards: