Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

Engine rebuild part 2

Here is the link for the series on a DVD http://realfixesrealfast.com/realfixesrealfast.com/Repairs/Pages/Rebuilding_an_engine.html setting the crank in place and checking to be sure everything clears


 


More Videos...


Engine build part 3
Here is the link for the series on a DVD http://realfixesrealfast.com/realfixesrealfast.com/Repairs/Pages/Rebuilding _an_engine.html Cutting the block where the clearance isn't enough Installing the cam bearings Installing the cam





Engine build part 4
Here is the link for the series on a DVD http://realfixesrealfast.com/realfixesrealfast.com/Repairs/Pages/Rebuilding _an_engine.html Using Plasti guage installing crank bearings installing timing chain





Engine rebuild part 1
This series is available on DVD Here is the link http://realfixesrealfast.com/realfixesrealfast.com/Repairs/Pages/Rebuilding _an_engine.html We are rebuilding a GM 350 5.7 engine. Now in this particular case we are also going to upgrade the engine to a 383 6.0 This is called building a "stroker" motor. In other words we are increasing the "stroke" of the engine which increased the torq & horsepower. If you are able & wanting to rebuild an engine, this video should give you a good overview of what to do. If you are having someone else build an engine for you, you will be able to see what's involved in the process





Engine build part 7
Here is the link for the series on a DVD http://realfixesrealfast.com/realfixesrealfast.com/Repairs/Pages/Rebuilding _an_engine.html Cylinder Head Adjusting valves Installing distributor





1998 Civic Engine Tear Down (Part 4) - EricTheCarGuy
Link to full engine R&R video: http://www.ericthecarguy.com/vmanuals/22-vmanual-store/149-1998-honda-civic -16l-engine-replacement-vmanual http://www.ericthecarguy.com/ Remember this guy? Yep since I'm moving I had my scrap picked up and this was still in the shop collecting dust so I decided to do the tear down on it, I'm glad I did because I got a nice little keepsake out of it. BTW don't yell at me for using my impact lets face it, this engine is scrap! --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG





Cobra Engine Build Part 1
This will be the first in a series on the engine build for my Cobra. This is a 351W bored 0.030" with a 408 stroker crank. The intake was converted to fuel injection and featured in a previous video. I will list components as much as I can.





E30 BMW 325i engine failure and after rebuild startup
My friends BMW engine failed here is some of the video we recorded and photos. I also included the first start up video.





How to Break In A New or Rebuilt Engine - EricTheCarGuy
Visit me at http://www.ericthecarguy.com/ I'm sure there is more than one way to do this but this is the way that I was taught and it seems to work as intended. The idea is to make sure the engine is fully lubricated before you start it up for the first time as we know all too well what happens to an engine without oil, in fact I forgot to show me filling up the oil filter with oil before I installed it sorry. Feel free to add your tips and tricks in the comments. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





How Oil Pressure Works - EricTheCarGuy
How Oil Pressure Works - EricTheCarGuy http://www.ericthecarguy.com/ Here is the second offering from last weeks set of videos. The most important thing to note with this is that oil pressure is not created by the pump but rather the resistance to the outlet flow of that pump and part of that resistance is the clearances between the bearings and the other parts inside the engine. If nothing else I hope you are entertained, enjoy! --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





CNC Cylinder Head porting and CNC Engine Blocks on the SAME Machine!
CENTROID ENGINE SHOP CNC Machining Center. 3 Machine tool in 1. CNC port cylinder heads and Blueprint and CNC machine engine blocks AND produce all kinds of CNC parts using the same machine.





How-To Machine a Chevy 350 V8 Small Block Engine
Chris Duke from Motorz TV http://www.motorz.tv takes our Chevy 350 small block to the machine shop to show you the process of machining a block. Special guest Britt Bostick from NuTech Engine Systems. Show notes: http://www.motorz.tv/machine-shop/ Website: http://www.motorz.tv/ Facebook: http://www.facebook.com/motorztv Twitter: http://twitter.com/motorz/ Watch the complete Chevy 350 engine rebuild series: 1. Tear Down: http://youtu.be/LZO1fWVxN4c 2. Machine Shop: http://youtu.be/e3r3wRBoXkk 3. Bottom End: http://youtu.be/gfrYWKi78zc 4. Top End: http://youtu.be/g46s-Vr4Br0 5. Finale: http://youtu.be/mvJNMN-oP68





Engine Building Part 1: Blocks
This is the first in an engine building series that focuses on blocks. I talk about general machining and options for rebuilding or starting a new motor.





Compression Testing and What You Can Learn From It - EricTheCarGuy
Compression Testing and What You Can Learn From It - EricTheCarGuy Here is a video on performing a compression test on an engine to assess it's mechanical condition. An engines ability to compress air and fuel is directly proportional to it's performance since an engine is nothing more than an air compressor once you take away all the controls. A compression test is a good general test that will give you an idea of the engine's overall health but it does not give specific information on what the problem is should there be one, for that a "leak down test" would be required, here is a link to that video. http://www.youtube.com/watch?v=WgrfT0LFMhc However if you find yourself looking for the source of a performance problem with an engine, this is a great place to start. This test is often overlooked in favor of looking at the fuel or ignition system, I think that's a mistake, if an engine can't perform mechanically no amount of electronics will make that better. Recently, I hit the 500 subscriber mark and I'd like to thank all of my subscribers past, present, and hopefully in the future for that. I enjoy making these videos and the fact that you seem to like watching them means a lot to me. So, thanks for subscribing, rating, and commenting, those little contributions make it all worth while. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Also see the video I did, "Octane Ratings and the 4 Stroke Engine Cycle" for more information on how compression works and why it is important. http://www.youtube.com/watch?v=8VWEwEveGTQ Thanks for watching and stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





383 Stroker 500HP+ rebuilt
Hey, a few days after everything was finished (old 383 Stroker with stock iron heads)the engine blew up with a broken piston.I will post a video about that later. Luckily the Engine-Block didn't suffer any damage and after disassembly of the whole motor it was the perfect 4-Bolt base for a real 500+ HP 383 Stroker. This time I wanted serious horsepower! So here we go, over 4.700$ in parts later...assembly is finished and right now the motor waits for going back into the Truck. Still a lot of other stuff to do at the Truck, but I think the Motor will be in the Truck running, in about 4-5 Weeks. Enjoy! The Parts used in the Rebuild 383 Stroker - Airflow Research 195cc SBC Eliminator Street Heads - COMP Cams Xtreme Energy Cam and Lifter Kits - 1.6 Harland Sharp Roller Rockers - SCAT Cast Crankshafts - 6.0 in. SCAT Pro Stock I-Beam Connecting Rods - Keith Black B122-040 Performance Pistons - Mahle Piston Rings - Trick Flow Chromemoly Pushrods - Hooker Headers 2806HKR - Hooker Super Competition Headers - ARP Head and Main Cap Bolts - TCI SFI Approved Flexplate - Professional Products 6.750 in. Harmonic Damper - Proform Billet Aluminum Timing Tab with Self-Powered LED Light - Peter Jackson noisy Gear Drive - Edelbrock Aluminium Timing Cover - Edelbrock Air Gap Performer RPM Intake - Edelbrock 750 Performer Carb - Fel-Pro Gaskets all arround - Milodon Freeze Plugs - MSD Digital E-Curve Distributor - MSD Blaster 2 Coil - MSD Super Conductor Wires - K&N 5" Air Filter - Proform Engine Dress-Up KIit - Dual 14" Perma Cool Fans - Mallory Fuel pressure regulator for return line system - new Battery - new 110 Amp Alternator Still to come: - True Dual 2,5" Flowmaster 50 Deltaflow Exhaust and 2 electric cutouts - Driveshaft Safety Loop - Rear Axle 4.10 Ring and Pinion with my powertrax locker Many thanks to all the support and the nice guys that helped me to build this beautiful Motor!!!Thanks guys you're great!!!:) That's it for now...stay tuned!





How an engine works - comprehensive tutorial animation featuring Toyota engine technologies
Nobody this video was designed for needed to know or cared about discontinued Supra (or other long discontinued inline 6) engines so don't bother posting a comment about them. This was 2007 and newer US MARKET ONLY Toyota technologies.




Which car is faster? Which Car is Faster?





Similar 1/4 mile timeslips to browse:

2004 Yamaha Road Warrior : 9.943 @ 137.250
Sam Vallas, Engine: Factory, Tires: Shinko Ultra Soft 190 rear


2004 Yamaha Road Warrior : 11.880 @ 117.000
J.B. EMBREY, Engine: 1700, Supercharger: NONE Turbos: NONE Tires: DUNLOP 200


2006 Yamaha Road Warrior xv1700: 12.008 @ 108.800
Leroy Faulkenberry, Engine: 102ci, Tires: shinko 003 190/55/17


2002 Yamaha Road Warrior : 12.132 @ 106.520
jeffy bloem, Tires: 260


1985 GMC Jimmy : 12.669 @ 107.940
David Alvarado, Engine: 353 Chevy, Tires: Radial T/A 275/60R15


2000 GMC Jimmy SLS: 14.600 @ 94.000
Rob Keefer, Engine: 4.3L V6 (262 ci), Supercharger: Vortech A-Trim Tires: F:25x4 B:26x9


1987 Chevrolet Astro : 14.720 @ 95.900
Steven Young, Engine: 350 cu. in. ZZ3 Crate, Tires: radial


1996 GMC Jimmy LS: 15.769 @ 86.700
Danny, Engine: 4.3 vortec,


1988 Chevrolet Astro : 15.927 @ 85.860
Manuel, Engine: 1969 350, Tires: Goodyear


1995 GMC Jimmy 2dr, AWD: 16.225 @ 82.260
Richard, Engine: 4.3,


1999 GMC Jimmy 4dr 4x4: 16.785 @ 80.210
Patrick, Engine: 4.3L V6,


1997 GMC Jimmy 4x4: 16.894 @ 78.850
Gary Wogaman, Engine: 4.3L, Tires: 31


1999 Chevrolet Astro LS: 17.234 @ 78.650
William Darney, Engine: 4.3 V6 Vortec (262),


1989 GMC Jimmy S15 2 Door Sierra Classic 4x4: 17.828 @ 74.740
Jim Mango, Engine: 4.3 Liter V-6, Supercharger: No Turbos: No Tires: BF Goodrich


 


©2014 DragTimes - Disclaimer