Just a quick 0-60 and some throttle punching in a 2005 Honda Accord Ex with a 2.4L 4 cyl and a 5 speed auto.
I actually liked this car better than the V6 version I drove a few weeks before. Pulled pretty good and the 5 speed auto really helped juice out the power
Jessica test drives the 2009 Honda Accord EX-L ( Part 2 of 3)
After speaking with Brandon about which Honda would best suit Jessica's
needs, she takes the 2009 Honda Accord EX-L out for a test drive.
Brandon explains to Jessica all the features to be found in the Accord EX-L
and Jessica tells Brandon what she thinks of the handling and the overall
Honda Accord VTEC Solenoid Gaskets Replacement
In this video I show you how to replace both VTEC solenoid valve gaskets
(valve to cylinder head and solenoid to valve) on 1994-1997 Accords.
This is a common cause of oil leaks on the upper passenger side of the
engine next to the distributor shaft seal, distributor o ring, and valve
It seems the same engineers who buried the Accords fuel filter also decided
to make the VTEC solenoid valve difficult to remove as well. One of the
bolts for the valve is buried so deep you have to partially drain the
cooling system and use a u-joint to get it out.
I take your through the process step by step from removal of all the parts
to re installation.
This video ran a bit longer than I wanted it to but considering how
deceptively easy this job looks at first glance (until you can't get that
one remaining hidden bolt on the valve off to remove it) I decided to leave
in as much detail as possible.
You will need to add new coolant and bleed the cooling system to avoid
engine damage after you're done. If you need that info here is the link to
my cooling system bleeding video.
Honda part numbers used in the video:
Solenoid to valve gasket: 36172-P0A-005
VTEC valve to cylinder head gasket: 15825-P0A-015
VTEC oil pressure switch o-ring: 91319-PR3-003
Thermostat housing to intake gasket: 91312-P0A-000
Thermostat housing to connecting pipe o-ring: 91314-PH7-003
These part numbers should work on all 1994-1997 Accords with VTEC but as
always check with your dealer to confirm these part numbers will work with
Intro and outro music by Kevin Macleod (Incompetech.com).
AFAccord's 417whp F23 Turbo Accord - HD Vids and Dyno
I only had a week to drive the car after it was tuned and wasn't able to
wire up my ECU switch in time to get any high Boost runs on video. Sorry guys! I'll make
plenty of high-Boost videos when I
come home, so subscribe!
Music rights belong to Gemini - Graduation of AEI Media.
Parts and Specs:
-F23 block, bored to 86.5mm
-Wiseco K20 spec pistons @ 10.2:1 compression
-SwainTech ceramic coating on piston crowns
-Crower F23 rods
-OEM main bearings (pink across all journals)
-ACL HX rod bearings
-Kaizenspeed balance shaft delete kit
-Bisimoto heat-shielding intake manifold gasket
-Bisimoto Pro valve springs
-Bisimoto Pro valve retainers
-Bisimoto cam gear
-Innovative 65A engine mounts
-Maxbore F23 throttle body
-MFactory limited slip differential
-DIY ramhorn turbo manifold
-DIY 2.5" charge piping from CXRacing
-28"x8"x3.5" FMIC from Go-Autoworks
-Triple-core half-size radiator from Go-Autoworks
-3" Straight pipe Exhaust
-3" Vibrant Flat black muffler
-Garrett T3/T4 57 trim turbo
-ACT Xtreme pressure plate
-ACT Streetlite flywheel
-ACT performance street disc
-Tial 38mm wastegate
-Tial Q BOV
-P61 OBD1 ECU
-Tuned using eCtune by the infamous... Joseph Davis!
Honda Accord 2.4 2013 - тест-драйв от InfoCar.ua (Хонда Аккорд 9)
Подробный тест Хонды Аккорд от команды
портала InfoCar.ua. В этом тесте мы выясняли,
каким стал новый Accord - более
"американским" или же получил больше
европейских повадок. У нас не тесте был
автомобиль с мотором 2.4, автоматом и в
топовой комплектации Executive
P2646 Honda Accord ,VTC strainer
P2646 Honda Accord ,VTC strainer. This Honda would not run at higher
speeds. It would start bucking and stall out if held to the floor. After a
bit of cleaning it seems to run fine. Do not try just removing the screens.
If you try to run a Honda with out the VTC strainer any dirt that the
screen would of caught will now go in to the little oil passages and be
hard to remove. I am also Leary of trying to add cleaners to the engine
when experiencing VTC Strainer problems.If the debris stuck in the VTC
Strainer bad enough to set a P2646 code then I would be afraid the debris
would break down smaller ,get through the VTC strainer just to get caught
up in the valve train oil passages.
How To Pull Honda Codes Without a Scanner -EricTheCarGuy
Link to code explanations:
Honda ABS Codes 1994-1997:
Honda ABS Codes 1998 and up:
Visit me at: http://www.ericthecarguy.com/
Discussion about this Video:
I feel like I should have made this video a while ago but the opportunity
never came up. Since I had this RL in my shop that had a check engine
light AND an ABS light I thought it was a perfect opportunity to put this
video together. I get asked all the time about my 'special tool' and it's
really nothing more than a Honda 2 pin connector with the input wires
soldered together. These connectors might be harder to find than you think
but if you run across a junk honda and one of these is on the harness grab
it. Even if you don't have the tool a paper clip or piece of wire will do
the exact same thing so don't sweat it if you don't have the tool because
shorting the connector is all you need to do.
I hope you find this video helpful.
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
Honda Accord VTEC timing belt and water pump Honda Accord VTEC High Detail How to
You can buy a quality belt and water pump online here
Special thanks to Spanky for filming this video for me. : ) My last
Honda Accord video was
very well viewed, but lacking in good sound, stability, and lighting so I
did another one with some help. Enjoy High Detail How to do a timing belt
and water pump Honda Accord VTEC
1994-1997 Honda Accord Rear Motor/Engine Mount
This is 1996 Honda Accord sedan 4 cylinder automatic. We are replacing the
rear vacuum assisted engine/motor mount. The mount is a common mount that
gets broken and starts causing vehicle vibrations when the car is in motion
or at idle speed.
The rear motor mount is all the same with the automatic transmission. Here
are the tool's that we used in this tutorial.
Jack lift with 2 jack stands, 1 wooden block
1/2 Impact wrench
3/8 and 1/2 for;
- 10mm,12mm, 14mm, 17mm sockets
- 12 inch and 6 inch extensions
- Universal joint
- deep 14mm socket
Long 14mm and 17mm wrench
flex head ratchet
needle nose pliers
Philip screw driver
Note: When putting everything back in the reverse order, here is the list
of what to do that will help make it easier for you.
- Hand thread all the bolts in place before you tighten them all down,
it'll make all the parts move easier and helps you put all the bolts back
in the proper position.
- It's easier to put the vacuum hose back from the bottom of the vehicle.
- Make sure to put the Exhaust bracket
in before you put the other 2 brackets on top to secure it in place.
- You have to play with the jack lift to put the bolt that goes through the
3 brackets to the transmission housing i.e Exhaust bracket, motor mount bracket, and the
Motor mount torque is 43ft. lbs, but its hard in tight spaces, so use your
impact wrench. Just don't over torque it!
BE SAFE, WEAR GOGGLES!
like and share this video!
If you have any questions or concerns, please feel free to leave comments
Like us on Facebook
Считывание ошибок с Honda Accord
Считывание кодов ошибок Honda Accord 7 своими
силами без специального оборудования.
Обязательно посмотрите видео про то,
какие видео регистраторы покупать
How to fix replace install a broken power window regulator motor Honda Accord 1994 1995 1996 1997
AH Parts Dismantlers http://www.ahparts.com / 877-859-0023
AH Parts sells only used Honda & Acura parts!
How to change fix replace install a broken power window regulator motor
replacement Honda Accord 1994 1995 1996 1997 - DIY Replace instructions
Send us a message about other tutorials you would like to see and we will
try our best to make them.
Want notifications of our new arrivals and other news? Visit us on Facebook