1995 Eagle Talon TSi AWD project; from Beginning to current. (Not completed).
In this video I take you on a little journy though the past 5-8 months and the work completed on my Talon. It is nowhere near done quite yet, well...for body it is. There are still many aspects I am planning on hitting, such as the engine..
I will be building a 2.3L stroker with a Holset HX35 turbocharger and the works.. But in time it will happen, certainly not right away. I have yet to apply for a job, but I am working on it. Thanks for watching.
God bless.
My 99 Eclipse Gs Project
This is the progression of my 1999 mitsubishi eclipse GS. The car is now going though a motor rebuild and is being turboed.
'97 Eclipse GSX Pro Street Build
I'm in the process of building a 1997 Eclipse GSX. I am finally starting to put it together and I just started this video. I will be editing it as I go.
1997 Eclipse GSX COMPLETE build in HD - 400awhp
A 7 month build in 26 minutes! A MUST SEE!
Bolt-on Modifications:
K&N filter element / FP Cast aluminum intake tube / Old school FP green turbo / FP turbo oil filter / Greedy electronic Boost controller / Apexi FMIC and short route steel hard pipes with Extreme PSI silicon couplers and T-clamps / External 38mm Tial wastegate / Tial BOV / Walbro 255 fuel pump / B&M fpr / 660cc Denzo injectors / BJ's polished SMIM / Stock TB / NGK 7mm spark wires / NGK spark plugs / turbo Back 3'' Megan Racing Exhaust / Megan Racing o2 housing / Balance Shaft Eliminator Kit / RRE Oil Catch Can / RRE Prothane Motor Mounts / Optima red top battery / RRE black silicon vacuum lines / Fluidamper harmonic balancer
Engine Management:
DSM link v3 on Speed Density / Auto meter Cobalt Boost, Egt, Oil pressure gauges / Apexi turbo Timer / Innovative MTX-L wideband gauge
Engine Internals:
6 bolt longblock swap, build by English Racing / Wiseco HD 1400 Forged Pistons 9:1 compression / Eagle H-Beam Rods / ARP Head Studs / OEM Crank / ACL Race Bearings / Head upgraded with GSC valve springs, TI retainers, Chromoly seats, Supertech valves with the 4-angle intake valve grind and the 4-angle radius Exhaust valve grind / HKS 272 intake and Exhaust cams / HKS adjustable cam gears / Cosmetic hg /
Drivetrain Modifications:
ACT 6 Pad Spring Race Disk #6224704 / ACT Extreme Pressure Plate #MB010X / Stock Flywheel / Braided Stainless steel clutch line / OEM throw out bearing / Sheppard Stage 4 Transmission, with Evo III first gear and input shaft, EVO III fifth gear, 4-spider center differential, New Shep Trans Spec 2nd Gear, New 1-2 Hub/Sleeve kit with Double Synchro Rings, New 5th Gear Synchro Rings, New 1-2-3-4- 5-R Synchro Springs, New Input, Output, and both Drive Shaft Seals, New Input Shaft Bearings, New Intermediate Gear Bearings, New Roll Pins, New End Nuts, New Center Diff Side Shims, New Nylon Shifter Pad, Shims for setting preload, New double Synchro 3rd and 4th gear, Double 3-4 Synchros, New Intermediate Shaft, Heavy Duty Shift Rails, Upgraded Rare Earth Magnet, Bead Blasted Case
Suspension Modifications:
Totika springs and shocks / Megan Racing front and rear strut bars / RRE Front camber correction kit / Les Schwab Rear camber correction plates
Interior Modifications:
Sparco 5pt harness on driver and passenger side / Cross seatbelt roll bar
Specs
• Power 399.38 AWHP and 319.43 TQ @ 26psi / English Racing AWD Dyno Jet 3/6/2012
• Redline: 8000rpm
• Weight: 3220lbs Full Weight 5/9/2011
420a turbo rebuild
The new setup for 10psi. Take note of my cams near the beginning. Tell me what you see is wrong. I'll let you know if you're right or wrong. Anyhooz. Enjoy.
The Story of my Talon Tsi
I purchased a 95 eagle talon tsi awd in the summer of 2009 after graduating High school. I did some minor modifications, bigger injectors, 14b turbo, 20lbs of Boost, safc tuning, pulled like a sombish. Then disaster struck, I threw a rod out my stock block. So 6 bolt swap time it is. Kept every thing stock for a stock rebuild. My intentions are cheap and reliable. Cleaned all engine components, new wiseco rings, honed block, cometic hg, arp headstuds, oem 6 bolt pistons and rods. Gonna be running 14b for the break in period then ill slap the 18g on and get a tune.
How to lap valves on a 1995 Eclipse Talon 420a head (non-turbo)
When my 1995 eclipse timing belt broke I knew that there was a 99% chance that the valves were bent in the process. I searched the internet for a good way to replace them, without having much luck. I figured I would try and come up with something myself, I figured I would document the whole process of valve lapping by video...hope this helps you if you are in the same bind as I was!!!
1995 Talon 420a Turbo Built!!!
1995 eagle Talon Fully built, Bored .20 over, weisco pistons, eagle rods, bored out valves, 272s Crowers, open down pipe right now, hahn portfuler, msd dis-2,turbonetics watercooled/oil T66 turbonetics turbo, fmic, and much more but not gunna list everything..
