1977 Vega: 7000 RPM Launch
This is a 1977 Chevy Vega. It actually has a 77' front end and a 73' back
end. It has turbo heads, 625 hp, Car
weight 2110, Titanium engine valve, Bored out 60, 15:1 Compression, Roller
Cam Shaft, 617 Dana 60 rear with spool, Aluminum Piston Rods, Cheetah
Shifter, Power glide with aluminum drums super stock 1.94 first gear. It
ran a 9.51 at 140 mph in this video.
1974 Vega Drag Car
A 1974 Vega Drag Car that I shot at the Knoxville Drag Strip on
4/6/12...this is a very nice race car...ck it out!!!
World Record Wheelstander
Interview with driver and video of the world record wheelie machine.
Groutaone official race gear found here http://www.groutaone.com/
71 vega wagon 383 stroker gopro hero 2
1971 vega, fresh 383 built by cope Brothers, built powerglide, dart heads
built by Cope Bros, running on trick 114 octane, 4150 hp, 9" narrowed ford
with 15x12x29 hoosier slicks, centerline 4"front,, with 4.88 gears, hooker
super comp ceramic coated headers edelbrock airgap,, Dynomax performance mufflers
guessing around 500 hp... just a little cruise around the hood testing out
the gopro hero 2 in Port Orchard WA.
1983 camaro with a 383 stroker pass
1983 Camaro with a 383
stroker aluminum headsE. at kilkare speedway ran a 12.23 @ 106 MPH when it
shut down rite after the 8th mile. AND THATS JUST THE BEGENING OF HEBER
1972 Nova 383 Street Strip
Second pass after driving it to the track and same plugs been in the motor
since this time last year around Feb 12. Engine has 3000 street miles on
it. First pass it spun as I didn't heat the tires good for the very first
pass. Tires are MT Drag Radials. Car ran firstname.lastname@example.org w/1.673 - 60' time.
Didn't change a thing on the car but make 2 runs. Next time I will pull 2
degrees timing and then play with the carb. Carb is an 850 Quickfuel.
Engine is a 383 (10.7 compression), Lunati Voodoo hyd. roller(560/565 -
243/251@.050"), AFR 195 heads, 4.10 w/Eaton posi and 30 spine Mosers. Stall
is a 4100 with a turbo 350 trans..
383 Stroker 500HP+ rebuilt
a few days after everything was finished (old 383 Stroker with stock iron
heads)the engine blew up with a broken piston.I will post a video about
that later. Luckily the Engine-Block didn't suffer any damage and after
disassembly of the whole motor it was the perfect 4-Bolt base for a real
500+ HP 383 Stroker. This time I wanted serious horsepower!
So here we go, over 4.700$ in parts later...assembly is finished and right
now the motor waits for going back into the Truck. Still a lot of other
stuff to do at the Truck, but I think the Motor will be in the Truck
running, in about 4-5 Weeks.
The Parts used in the Rebuild 383 Stroker
- Airflow Research 195cc SBC Eliminator Street Heads
- COMP Cams Xtreme Energy Cam and Lifter Kits
- 1.6 Harland Sharp Roller Rockers
- SCAT Cast Crankshafts
- 6.0 in. SCAT Pro Stock I-Beam Connecting Rods
- Keith Black B122-040 Performance Pistons
- Mahle Piston Rings
- Trick Flow Chromemoly Pushrods
- Hooker Headers 2806HKR - Hooker Super Competition Headers
- ARP Head and Main Cap Bolts
- TCI SFI Approved Flexplate
- Professional Products 6.750 in. Harmonic Damper
- Proform Billet Aluminum Timing Tab with Self-Powered LED Light
- Peter Jackson noisy Gear Drive
- Edelbrock Aluminium Timing Cover
- Edelbrock Air Gap Performer RPM Intake
- Edelbrock 750 Performer Carb
- Fel-Pro Gaskets all arround
- Milodon Freeze Plugs
- MSD Digital E-Curve Distributor
- MSD Blaster 2 Coil
- MSD Super Conductor Wires
- K&N 5" Air Filter
- Proform Engine Dress-Up KIit
- Dual 14" Perma Cool Fans
- Mallory Fuel pressure regulator for return line system
- new Battery
- new 110 Amp Alternator
Still to come:
- True Dual 2,5" Flowmaster 50 Deltaflow Exhaust and 2 electric cutouts
- Driveshaft Safety Loop
- Rear Axle 4.10 Ring and Pinion with my powertrax locker
Many thanks to all the support and the nice guys that helped me to build
this beautiful Motor!!!Thanks guys you're great!!!:)
That's it for now...stay tuned!
drag racing crashes
Drag Racing crashes from all around the world, mainly NHRA, ANDRA, IHRA.
Disclaimer: I do not own the music and picture used in this video. All
credits belongs to their real owners. No copyright infringement intended.
Intro music created and composed by "Nick Phoenix / Thomas Bergersen -
Heart of Courage (Choir)-Extreme Music/2 Steps from Hell"
Music played by Charlie Parra del Riego, so check his channel out.
If you dont like Metal music press mute to watch this video so you dont
whinge and bitch about it in the comment section.
132702 / 1975 Chevrolet Vega Cosworth
For more information on this vehicle visit http://tinyurl.com/7ls72l8
This all original 1975 Cosworth is one of 2,061 cars produced for the '75
model year, has only 291 actual miles, and has all of the rare and
difficult to find Cosworth Vega parts right where the factory installed
Assembled at GMs historic Lordstown, Ohio manufacturing facility, and
finished in standard issue 1975 Cosworth Vega code 19 black acrylic
lacquer, CV number 1094 is every bit as clean today as when it left the
showroom floor. The car has remained in all original, non-repaired
condition thanks in small part to GMs anti-rust improvements, and in large
part to immaculate maintenance and care given by loving owners throughout
its life. Today, it features an old school factory appeal that you just
can't find in its restored peers.
With 110 horsepower and a 6,500 RPM
redline, the Cosworth Vega was one of the hottest performing cars available
in 1975 and featured a hand-built mill from GM's Tonawanda engine plant
that was individually signed by its builder on a sticker that occupies the
cam cover. Measuring in at 122 cubic inches, and wearing a correct partial
VIN of 40392, this Vegas DOHC inline-four features sturdy forged aluminum
pistons, a heat-treated forged steel crankshaft and forged connecting rods
that both reveal the engines racing ancestry and assure high performance
durability. To meet ever increasing US emissions standards, a custom
designed stainless steel Exhaust
header and Bendix electronic fuel injection with pulse-time manifold
injection, four injector valves, an electronic control unit (ECU), five
independent sensors and two fuel pumps were installed. Thanks to this
revolutionary engine, the Vega was the first Chevrolet car to feature
electronic fuel injection which warranted an HEI distributor for increased
spark and a heavy duty radiator for increased cooling.
At the bottom of this sophisticated Chevrolet, an original Saginaw 4-speed
manual transmission, which wears a correct 338835 casting number and a
correct 15U240392 partial VIN, sends power to an original 10 bolt rear end
that's packed full of stout 3.73 gears. Holding that sports car drivetrain
off the ground is an original F41 heavy duty suspension which includes a
'torque arm' rear end for optimum rear axle power control, larger rear
stabilizer bars, Vega GT springs and shocks, provisions for the Vega's
"fast Steer" option and front disc brakes. At the center of the car, an
original single pipe Exhaust system
snakes spent gases along the floorpan to a factory replacement muffler
which barks an exotic four cylinder growl through two polished stainless
tips. And at the corners of the car, 13 inch British-made, gold-painted
cast aluminum wheels spin correct BR70-13 Goodyear Custom Steelgard Radials
around chrome lug nuts and satin finished Chevrolet center caps.
Take a look inside this pristine Cosworth Vega and you'll find the typical
all business/no compromises black interior that these cars have built a
reputation for. The custom bucket seats, which are completely fresh and
display no signs of wear at all, nicely complement a 100% straight and
crack-free dash. Inside that dash, an engine-turned gold bezel houses a
Cosworth exclusive 8,000 RPM tachometer between a 120 MPH speedometer,
gauges for the engines vitals and a gold-plated plaque which is branded
with the cars 1094 build sequence number. Below those gauges, a correct
radio delete sits next to the cars original heater/defroster; and in front
of those gauges, a familiar black steering wheel is centered behind a blue
Cosworth Vega horn button emblem. At the floor, the booted shifter for the
Borg Warner T10 transmission springs up from like-new black carpet which is
protected by color-keyed floor mats. And at the roof, the cars original
mouse fur headliner stretches tightly around vinyl sun visors and a bright
courtesy lamp. The door panels, which look as good as new, are decorated
with attractive stainless trim and chrome handles for both the doors and
windows. And the hatch, which is lined with the same black carpet as the
floor boards, appears to have never been used.
If you're a serious collector who's been searching for something rare and
unique, here's your opportunity to own one of the nicest and most
underappreciated cars on the planet! Call, click or visit
http://RKMotorsCharlotte.com for more information on this awesome car!
1972 Vega Pro Street
A 1972 Pro Street Vega I shot while at the Shades Of The Past Rod Run
2013.....This car has been in the family since almost new...Driven by the
current owners Dad back and forth to work for sixteen year....A cool
Car...With a cool history...check it out!!!...Make sure you follow me so
that you don't miss any of the other awesome cars I shot at this show!!
My apparel provided by:
Check them out!!!