More Videos...

How To Solve Honda Idle Problems - EricTheCarGuy
Visit me at: http://www.ericthecarguy.com/ Before posting questions about Honda idle problems please read this: http://www.ericthecarguy.com/forum/8-Service-and-Repair-Questions-Answered-Here/41476-solving-honda-idle-issues-hunting-idle The viewers have chosen and this weeks video will be about solving Honda idle problems. I'm really not surprised as I get a lot of questions and requests about this very subject. Here are the links I promised in the video that will help you address specific issues mentioned in the video. How To Bleed a Cooling System http://www.youtube.com/watch?v=zUpXgAJ1gjU How to Check for Vacuum Leaks http://www.youtube.com/watch?v=9CPqbaSgcok Reading Check Engine Light Codes http://www.youtube.com/watch?v=BD05sPclLyE Diagnosing an Overheat http://www.youtube.com/watch?v=hUzOTnsWImI Hopefully when your done checking all that stuff out you will have solved your Honda's idle problem, if not leave a comment or send me a message and I'll see what I can do just make sure you have tried all the stuff in the videos first as that saves me from typing so much. I also want to add my "Idle Speech" into the mix here: http://www.ericthecarguy.com/forum/8-Service-and-Repair-Questions-Answered-Here/41475-solving-honda-idle-issues-rough-idle   There are a lot of things that can contribute to an idle issue, in fact in the end it may still be there to some degree because of the nature of that engine however here are some things to start with. First start with a good tune up, use NGK or Nippon Denso plugs, don't change the wires if they are OE, if they aren't OE you might consider NGK wires as they are very good and less expensive then OE.  A quality cap and rotor should be good.  A new air filter also helps. Don't change the PCV valve, if you see an aftermarket PCV valve in there put a Honda in, believe it or not I've seen idle issues caused by aftermarket PCV valves, the OE's last just about forever so you can easily justify the expense. Next a good valve adjustment, this goes a long way to smooth out the idle if done correctly, mess it up and things can get a lot worse though. While you have the valve cover off check the timing belt tension, if you feel a lot of slack this can cause the cam to 'chunk' as it spins causing a rough idle.  If you think the belt has been on there for some time then you might consider changing it and resetting the tension properly, if it's not ready for replacement you can reset the tension to take up the slack. DO NOT adjust the idle screw under any circumstances, it is set at the factory and that is the reason it was sealed in the first place. If you find that the seal has been broken and you have a low idle and you have done all of the above then you might turn the screw out a little to see if that helps the idle but only enough to try and bring it back to where it was before it was adjusted in the first place. Last clean the screen in the Idle Air Control valve, this can get clogged up with carbon over time and cause the flow through it to be restricted which can cause idle issues. If you still have a 'rough' idle after all of this THEN look to the engine mounts as you want to be sure the engine is running correctly before you go for those as the one in the back is a real pain to replace. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

Honda Accord Valve Adjustment - EricTheCarGuy
This one was a request from a couple of viewers, I like to keep you all happy so here you go. This video is actually taken from a larger video I call "Accord Smackdown", in it I replace the timing belt, radiator, a major service, and some other stuff that I don't remember. I think there will be a couple more videos from this "smackdown" in the future, there is some good stuff in there that I think you will like and possibly learn from. If you have other topics you would like covered don't hesitate to let me know, I'm happy to give you what you want. Post them as text or video responses to this or any of my videos. I'm going to get the part number for the tool I used in the video sometime next week and post it here so keep your socks on and check back sometime next week. Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://carquestions.ericthecarguy.com/viewforum.php?f=2&start=0&sid=82fdbaff5e8b157727e9723c1fbf36c0 Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

Honda No Start? POSSIBLE Main Relay - EricTheCarGuy
Honda No Start? POSSIBLE Main Relay - EricTheCarGuy http://www.ericthecarguy.com/default.aspx Here is a GREAT website article about soldering these I strongly suggest you check this out before doing this repair. http://techauto.awardspace.com/mainrelay.html The first of the "Quick Tips". I think I'm going to throw one of these in from time to time to keep things lively. So if you have a Honda or Acura that is not starting DUE TO LOSS OF FUEL PRESSURE this is a good place to start. You may be able to repair the main relay normally found under the dash on the drivers side. If this helps great remember me fondly and pass my name along because I just saved you at the very least about $80, at the most $200. I will be upgrading my website very soon, in fact I will post a video when it is up. Cool new things on the horizon for ETCG and YOU the viewer. So if you want take a look at the old site because it's days are numbered. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Till next time Be Safe and Stay Dirty. Oh yea, and have fun too. ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

How To Bleed A Cooling System - EricTheCarGuy
How To Bleed A Cooling System - EricTheCarGuy Kind of a request, I've described this procedure a few times in print but never made a video. As I said in the video if your having issues with a fluctuating idle, no heat, or an overheat problem you may want to start here. Also, if you have just serviced the cooling system in any way this is the procedure I recommend to fill it back up. The only regret I have with this one is the end where I didn't shoot footage of closing up the radiator using the tool that I used in the video, I may show it at some point in the future. Here is a link, perhaps an old link, to the "Spill Free Funnel" http://www.amazon.com/s/?ie=UTF8&keywords=spill+free+funnel&tag=googhydr-20&index=aps&hvadid=4031750381&ref=pd_sl_67pg14j0u6_b --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

Honda Accord Fuel Filter Replacement
A fastener by fastener tutorial for replacing the fuel filter on a 1997 Honda Accord. This process applies to Accords manufactured from 1994 to 1997. Honda recommends replacement once every 2 years or 40,000 miles whichever comes first. While I have found many videos on replacing the fuel filters on the easier Civics I have understandably seen none for the Accords. The main reasoning being they are buried deep and are difficult to access and unless you know which tools to use they can look almost impossible to remove. I'll take you through it step by step and show you what tools you'll need to get the job done. Intro and outro music by Kevin Macleod (Incompetech.com).

P0401 EGR Insufficient flow test
Here is how to test code P0401 and the DPFE sensor. Sure, the DPFE has a high failure rate, but do we "throw" the part at it, or do we test it to be sure it's actually failed. AND, this is a great way to confirm the repair to prevent a "come back"

Diagnosing the Engine Knock
Trying to figure out what the engine noise is. Looks like lifters that won't drain down plus maybe some plugged up oil squirters.

VTEC ENGINE
video about how 2 rebuild a B16A2 ;)

EGR valve cleaning or Replacements Honda Accord 2000 ex V6
you can also visit my web page to view videos "https://sites.google.com/site/lowermycarmaintenancecost/videos/home"

What is VTEC and How Does it Work? - EricTheCarGuy
What is VTEC and How Does it Work? - EricTheCarGuy I've been editing some full length video this week and I came across this bit from a car I worked on last spring. The animations are courtesy Honda Motor Company, thanks guys. I think the title is self explanatory and I hope the video makes it a little clearer for those who are curious about this system and how it works. I've had a couple of requests for this and I hope this answers those questions. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG

1998 Honda Civic Engine Part 1 - EricTheCarGuy
Link to full version of this video: http://www.ericthecarguy.com/vmanuals/22-vmanual-store/149-1998-honda-civic-16l-engine-replacement-vmanual Link to part 2: http://www.youtube.com/watch?v=U_HQUCIXD90 Visit me at: http://www.ericthecarguy.com/ Well here it is the first of the Civic engine series, I hope you like these as they are a little 'lighter' than those trucks I've been working on lately. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG

P0401 Diagnosis EGR Low Flow Honda Civic
Here I point out the plate that lies underneath the fuel rail, so you can see what you need to remove to clean your passages; which will allow you to clear your P0401 code. Diagnosing the p0401 DTC. Click here to show thanks, and help support Fixbook: http://www.hondahowto.com/p/blog-page_25.html Click this link to Subscribe: http://www.youtube.com/subscription_center?add_user=Hondahowto1&annotation_id=annotation_59253&feature=iv&src_vid=QSNjtNYuD18 Click here to check out the the "Car Runs on 2 cylinders" series: https://www.youtube.com/playlist?list=PLoA1-alJGwfnWZvOZtIjPnQX88q1n3GWA&feature=view_all I, Jordan, assume no liability for anything you choose to do to your car, before, or after watching one of my videos, including this one. All DIY repairs, or modifications, you perform to your car are made at your own risk. Sometimes, even if you've done everything the right way, you can destroy, or damage, a piece, or part. You must understand this; part of doing a repair, and/or modification is messing up sometimes. Also, if for some reason, I do give incorrect instructions, and something breaks because you followed my instructions, I still will not reimburse, or pay, in any way, for whatever cost that may be incurred due to following my wrong instructions. Don't do anything to your car unless you yourself feel comfortable, & confident in doing so. Fixbook DIY Car Repair

Oops, Axle and Ball Joint Replacement - EricTheCarGuy
Oops, Axle and Ball Joint Replacement Sorry I missed you last week, I had this video half done and didn't get a chance to finish. Well we have our 1990 Accord again, I'm getting some mileage out of this one but I don't mind cause there are still quite a few of these on the road and a few of you have claimed ownership to one of these 4th generation Accords, so enjoy. A couple of things to note, I could do a video on taking out the wishbone bolt alone, I've run into a few problems here such as a rusted bolt that won't come out of it's bushing as one example, perhaps future videos will show how to overcome this problem. I thought this one went together well despite the fact that you might be getting sick of Honda Accords, I still have more from other makes that I haven't edited or posted yet. I have more to this video as well that may show up in DVD form at one point, YouTube only gives me 10min to work with but I think that is enough to get you started and not lose interest. Perhaps you could help by submitting questions in the form of text responses or what I would really like is a video response to something I've put out there, that would be great. Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

Removing Brake Rotor Screws That Won't Come Out - EricTheCarGuy
Removing Brake Rotor Screws That Won't Come Out - EricTheCarGuy I think the title covers this one. Honda's are famous for this so I made this little video to help you should you be in this situation. Wear your safety glasses when you do this or whenever you hit things, getting crap in your eye sucks, trust me. Impact drivers can be found at your local tool supplier. If you don't have a hammer I don't know what to tell you. This doesn't seem to require a long explanation so I'm going to stop typing now. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.

Honda Accord and Civic Transmission Fluid Change
I show you how easy it is to change your transmission fluid on a 1997 Honda Accord. This process applies to Civics as well. A special note. Some 90s Civics have a CVT transmission use Honda CVT fluid on them otherwise use ATF Z1 (now ATF DW1) for a non CVT automatic transmission. Honda fluid part numbers: ATF Z1 Part Number: 08200-9001 (Discontinued) Replaced by: ATF DW1 Part Number 08200-9008 CVT Fluid: 08200-9006 Since the production of this video Honda has discontinued ATF-Z1 and replaced it with ATF-DW1 it's a drop in replacement for vehicles that used ATF Z1. The fluid change interval by Honda is every 30,000 miles. Intro and outro music by Kevin Macleod (Incompetech.com).