Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

How To Install Replace Front Wheel Bearing Hub Grand Prix Impala Regal 1AAuto.com

http://www.1aauto.com/1A/wheel-bearing-hub-front 1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning front wheel bearing hub. This video is applicable to many 97, 98, 99, 00, 01, 02, 03, 04, and 05 GM front Drive Vehicles including Chevy Impala, Monte Carlo and Venture, Buick Century, Lesabre, Regal, Park Avenue and Riviera, Cadillac Deville, Eldorado and Seville, Olds Aurora, Intrigue and Silhouette, Pontiac Bonneville, Grand Prix Transport and Montana.


 


More Videos...


How To Install Replace Front Wheel Bearing Grand Prix Impala 1AAuto.com
http://www.1aauto.com/1A/wheel-bearing-hub-front 1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning front wheel bearing hub. This video is applicable to many 97, 98, 99, 00, 01, 02, 03, 04, and 05 GM front Drive Vehicles including Chevy Impala, Monte Carlo and Venture, Buick Century, Lesabre, Regal, Park Avenue and Riviera, Cadillac Deville, Eldorado and Seville, Olds Aurora, Intrigue and Silhouette, Pontiac Bonneville, Grand Prix Transport and Montana.





How To Install Replace Front Wheel Hub Bearing GM Front Wheel Drive PART 2 1AAuto.com
http://www.1aauto.com/1A/wheel-bearing-hub-front 1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning front wheel bearing hub. This video is of a 1999 Pontiac Grand AM. This process is the same for many midsize GM front Drive Vehicles including Chevy Cavalier, Olds Achieva Cutlass Alero, particularly the Grand AM, years 99, 00, 01, 02, 03, 04, and 05.





How To Install Replace Front Wheel Hub Bearing Buick LeSabre 00-05 1AAuto.com
http://www.1aauto.com/1A/wheel-bearing-hub-front/Buick/LeSabre/TKSHF00002 1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning front wheel bearing hub. This video is applicable to the Buick LeSabre, years 00, 01, 02, 03, 04, and 05.





How To Replace a Front Wheel Drive Axle - EricTheCarGuy
If you start to notice your FWD vehicle clicking when you make a tight turn, you might have an issue with the outer CV joint. If you make a right turn, it's usually the left side that's bad and vice versa. Most axles are easy to replace and the one depicted in this video is fairly typical of what you run into. The main differences come in with how the lower ball joint is attached. I think this part will give you the most trouble. I often get asked about what to torque the axle nut to. To be hones, I don't know. I've only ever run them down with my impact. I've never had an issue doing it that way and I don't think you would either. Just be sure to stake the nut or install the cotter pin and retaining clip if it has one. If you'd like more information on how to deal with suspension noises, check out this article I wrote on the topic. http://www.ericthecarguy.com/faq/diagnosing-noises-in-your-car Video on CV boot replacement: http://www.youtube.com/watch?v=-S-ofMoWsr0 The best place for answers to your automotive questions: http://www.ericthecarguy.com Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts Twitter: https://twitter.com/EricTheCarGuy Google+: https://plus.google.com/100195180196698058780/posts Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content Stay Dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





2003 Mazda Front Wheel Bearing Replacement (Press In Type Bearing)
Wheel bearing replacement in a 2003 Mazda Protege 5. Press in style bearings done without using a shop press. Specific for Mazda Protege, but many of the techniques will apply to vehicles with pres-in-style wheel bearings. It's a good idea to try to use the bearing-press-kit the way it was intended. If the bearing doesn't budge, BE CAREFUL using a breaker bar. The bolt supplied with the press-kit is not very strong...it with probably shear off the head. Try to give the bearin a few hits with a sledge hammer as seen in the vid..it will get the bearing moving. Then you can use the press-kit, and it should finish pressing out the bearing. Pressing in the bearing with the kit should be no problem.





Replacing a wheel bearing
Replacing a wheel bearing in a 2001 Buick Lesabre





How To Remove Pressed-on Bearings - EricTheCarGuy
http://www.ericthecarguy.com/ I know this one does not cover an entire procedure but it just worked out this way. I did however want to show how to remove this type of bearing should you run into it. I didn't show the installation for 2 reasons on this, first, I just didn't have the time to shoot it, and second I recommend pressing new bearings on rather than hammering them into place (I don't have a press yet). I would say that hammering them is OK but you risk damage to the bearing and if that happens it is a lot of work and more money to fix it. Be sure to wear your safety glasses! Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.  --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





2002 Chevrolet Impala Wheel Hub Bearing Replacement
Purchase this bearing here: http://apdty.com/item.wws?sku=513121&itempk=100426 In this video we'll show you how to replace the wheel hub bearing on a 2002 Chevy Impala.





Wheel Bearing Replacement with Basic Hand Tools
Click Here to Subscribe! http://youtube.com/carsntoys Website: http://carsntoys.net Front wheel bearing replacement on a 2002 Buick LeSabre with basic hand tools. Please note, this vehicle has the bearing built into the hub. Some vehicles may have a taper rolling bearing (usually older vehicles have this setup) or some vehicles may need the bearing to be pressed out of the hub. In this case, the hub & bearing is all one unit. Don't forget to wear safety glasses. Please note: This video is being performed by an experienced tech. Any attempt to repair automotive parts and/or systems carries risk of personal injury. Always adhere and follow safe practices when working on vehicles. Such as, use safety glasses, jack stands, no loose clothing, etc. No guarantee or warranty is implied. Use the information in this video at your own risk. Publication, reproduction or distribution of this film is strictly prohibited.





How to Diagnose a Noisy Wheel Hub and Bearing
It can be tricky trying to diagnose a front end suspension noise. We show you a simple technique here simply describing how to diagnose a wheel hub noise. Age, mileage and road conditions can really take a toll on wheel bearings. This particular wheel bearing is a sealed bolt on unit that can only be replaced as an assembly. This procedure can work on many different styles of wheel bearings and front end noises. The automobile consist of: Powertrain: 1. Engine: • Fuel System: Purpose is to deliver fuel to the engine. It consists of the fuel tank, pump, gauge/sensor, filter, pressure regulator and injectors. • Air Intake System: Purpose is to clean and direct outside air into the engine. It consist of air filter, ducts, air plenum and intake manifold. • Exhaust System: Purpose is to direct Exhaust gasses out of combustion out of engine. It consists of the Exhaust manifold, converters, pipes and mufflers. • Cooling System: Purpose is to remove excess heat from the engine. It consists of water pump, hoses, radiator, thermostat, cooling fan and coolant recovery tank. Also the oil system serves as a cooling system as well as a lubricating system. It consist of oil pump, pan, filter and cooler. Drivetrain: 1. Clutch: Purpose is to connect the engine and transmission together. It consists of clutch drive disc, driven disc, release bearing, clutch fork, cable, slave cylinder, master cylinder. There are three types of clutch systems: mechanical, cable and hydraulic. 2. Transmission: Purpose is to match engine speed to road speed. Two types used are manual or automatic. These consist of gears, linkages, cables and converters for automatics. A manual is connected to the clutch by a flywheel and automatic by a flexplate. 3. Driveshaft: Purpose is to connect the transmission to the rear axle. It consists of a slip yoke, shaft and universal joints. 4. Rear axle differential: Purpose is to change the angle of motion from engine to the wheels. It also divides torque between the wheels. It consists of a ring and pinion gear, carrier, bearings, crush sleeve and axle shafts. 5. Wheels/Tires: Purpose is to provide traction to the road as well as carry the weight of the vehicle. Vehicle Control Systems: 1. Brakes: Purpose is to slow and stop the vehicle. It consists of master cylinder, brake Booster (vacuum or hydraulic), calipers, drums, pads and rotors. 2. Steering: Purpose is to direct vehicle in the required direction. Consists of steering gear (rack & pinion), steering wheel, column, inner/outer tie rods, pump, reservoir, hoses and pipes. 3. Suspension: Purpose is to provide stability and handling while also providing comfort to the ride. Consists of shocks, struts, sway bars, end links, springs, trailing arms and bushings. Comfort System: 1: Heating Ventilation Air Conditioning (HVAC): Heats and cools interior air to passenger comfort. Also circulates outside and inside air. • Air Conditioning: Consist of condenser, compressor, accumulator (receiver/dryer) orifice, expansion valve, hoses, evaporator, controls, actuators and modules. • Heating: Consists of heater core, valves, hoses and switches. Electrical Systems: 1. Power Generation: Creates electrical power to run all the electrical systems. Consists of the alternator. 2. Power storage: Stores unused power to start the car and supply voltage to the alternator to create more electricity. • Both systems consist of wiring, harnesses, fuse, relays and modules.





How to clean your wheels the good way
How to clean your wheels. The good way. Music : Love Me Lots - Bridge & Law Remix Midnight City M83





How To Find Suspension Noises 101 - EricTheCarGuy
How To Find Suspension Noises 101 - EricTheCarGuy http://www.ericthecarguy.com/ This is probably one of the most popular questions that I get so I'm happy to bring you this one because I know it's going to save me some typing. I may have missed a couple of things but I believe I've covered the basics on this one so this video should give you more than enough to start with. --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Pressing out a front wheel bearing
How to get at and press out a wheel bearing. I used a12 ton hydraulic press and it was lots of power to press it out as some were wondering about that part. Be sure to not get hurt using the press as metal will fly under pressure if not placed safely.





Pressed wheel bearing replacement (without a press...)
The bearing is 24 years old and has 155 000 kms. It was quite easy thanks to a "special" trick. No press used : ) and the only annoying task was to remove the outer race with a hammer and a chisel.





How To Replace Brake Fluid - EricTheCarGuy
As I said in the video I've been asked about this video for some time and I was happy to get the opportunity to make it. Now that I think about it however I did not address ABS systems in this video however the Subaru used does have ABS. For the most part, you can replace the brake fluid and not have to worry about the ABS, however in some cases you might need to bleed the system with a scan tool in order to get the brakes to work properly. Be sure to check the service manual of the vehicle you're working on before committing to bleeding at the wheels. If you're just removing the fluid in the master cylinder, you should not have to worry about the ABS at all. If you're having brake problems, check out this article I wrote on handling brake problems: http://www.ericthecarguy.com/faq/solving-brake-problems The best place for answers to your automotive questions: http://www.ericthecarguy.com Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts Twitter: https://twitter.com/EricTheCarGuy Google+: https://plus.google.com/100195180196698058780/posts Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content Stay Dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Which car is faster? Which Car is Faster?




Similar 1/4 mile timeslips to browse:

1987 Buick Regal Turbo-T: 8.690 @ 158.460
Dan Strezo, Engine: 274 c.i., Turbos: T88-T4 Tires: MT 29.5x10.5 Non-W


1986 Buick Regal Grand National T-type: 8.900 @ 154.000
Jack Cotton, Engine: 4.1l, V6, Turbos: single Turbonetics T76 Tires: MT 29-10.5-15


1984 Buick Regal : 9.610 @ 146.000
BAZTEK,


1981 Buick Regal GS: 9.980 @ 139.071
RONALD BEY, Engine: 494 ci, Tires: FUTURA


1987 Buick Regal : 10.200 @ 132.120
Rich Lenz, Engine: 454, Supercharger: none Turbos: none


1986 Buick Regal : 10.270 @ 132.970
Bob Heinz,


1996 Chevrolet Impala SS: 10.374 @ 130.520
Glen Koenig, Engine: 461 LS-6 BBC, Tires: Hoosier 10.5x29W rear, Morose DS2 28x4.5 front


1986 Buick Regal T-Type WH1 Designers Series: 10.750 @ 122.000
Banning Cohen, Engine: .040 over stock block 3.8v6, Turbos: PT67 Tires: 28x11.50x15 Hooser QT Pro


1987 Buick Regal Turbo T: 11.251 @ 121.000
John, Engine: 231, Turbos: 1 Tires: Mickey Thompson ET Radials


1986 Buick Regal limited: 11.290 @ 120.320
timmy, Engine: 464 buick, Tires: 205x15 ft 28x10.5x15 micky thom rear


1968 Chevrolet Impala SS 427: 11.339 @ 116.420
C. Moore, Engine: 496 Chevy self built, Tires: M&H rear BFG front


1964 Chevrolet Impala : 11.488 @ 116.620
Jeff, Engine: 406, Tires: MT Drag Radials


1987 Buick Regal T-Type: 11.500 @ 120.000
Bob V, Engine: 3.8 L, Turbos: CPT-65 Tires: BFG DR


2003 Chevrolet Impala LS Turbo: 11.540 @ 120.230
jeffery klo, Engine: 3.8 v6, Turbos: 62-1 Tires: MT ET drags


1996 Chevrolet Impala SS: 11.647 @ 119.360
Glen Koenig, Engine: Stock 354 LT1, Tires: GY Front runners, Hoosier QTP 28x11.5


1987 Buick Regal Limited T: 11.670 @ 117.000
Timothy Dirks, Engine: 3.8, Turbos: Stage V Ball Bearing Tires: Hoosier QTP 26x9


1996 Chevrolet Impala SS: 11.800 @ 112.000
Joe, Engine: 6.2 LS3, Supercharger: No Turbos: No Tires: Nitto 305/35/18


1996 Chevrolet Impala SS: 11.895 @ 116.650
Terry Kehne, Engine: 385 CID LT1, Tires: front: 275/75R17 Riken, rear 226x10.-15 MT ET Drag


1962 Chevrolet Impala sedan: 11.898 @ 113.067
tony, Engine: 454,


1995 Chevrolet Impala SS ATI ProCharger Supercharger: 11.940 @ 114.770
David Dickey, Engine: 396 Storker LT-1, Supercharger: ATI ProCharger D-1sc Tires: BFG Drag raisals Rear, BFG KDW's front


 


©2014 DragTimes - Disclaimer