How to MIG weld a patch in car floor pan. E30 bmw.
This is my first welding how to video. I have been welding new steel into
my 325i sport for the last 6 months. When I started there were not a lot of
HD youtube videos on mig welding on cars so I thought I would make one.
I used 1.8mm steel sheet, a Lincoln Powermig 180c welder and 0.6mm super
arc wire with a Argonshield shielding gas.
I am sorry my head is in the way of some of it. I didn't realise until I
looked through the footage later.
1965 Chevelle Quarter Panel Install Pt. 1 V8TV
http://www.v8tvshow.com - 314-783-8325 - PART 1 - Quarter panels are one of
the most rust and dent-prone parts of musclecars, and our 1965 Chevelle had
some of each. Mostly dents. Thankfully, OPGI came out with new
reproduction full quarter panels for 1965 Chevelles. In this video, we
show you how to remove your old panel and install the new. Also applies
to other GM A Bodies like Skylarks, Cutlasses, GTOs and others.
Quick rust patch on 1980 Z28 floor board
My friend picked up this all original 1980 Z28 a few years ago. It sat for
many years and someone shot out a side window. The rain got in and put
some rust on the passenger side floorboard. Tonight I made a patch and
welded it in for him.
Sexy Girl - 1200hp Camaro!!!!
It's been a while since we have done any girl ride along videos so we
decided to start back up again!
This is in a 1200hp Camaro that runs low 9's!
More girl videos coming soon! Enjoy
Fan Page: http://www.facebook.com/HighTechCorvettefans
HPD Facebook: http://www.facebook.com/HoustonPerformanceDriving
Trunk Pan Replacement-How to replace a trunk floor from How to ASAP
Center Trunk Pan Replacement, This clip is from a 90+ minute DVD from
howtoASAP.com. Nationally recognized car builder, Craig Hopkins, will take
you through the step by step installation of a center trunk floor. You will
learn methods and tips which will give you professional results with your
do it yourself project. Shot in HD, this DVD is packed with information
that will stop you from making costly errors and will leave you with a
repair that will be hard to spot. If you dont want to do it yourself, this
DVD will help you pick the right shop to restore your car. No matter what
your skill level, this DVD will help! Be sure to check out the
howtoASAP.com DVD on Mig Welding Automotive Sheetmetal. It has been getting
great response from people wanting to improve their welding skills.
Episode 70 Part 2 Seamless floor pan installation, 1965--70 Mustang, Autorestomod
We finish the installation of the National Parts Depot Mustang floor pan in our weekend
project 1968 Mustang
hardtop! In this episode we only replace the sections needed. Gary Jackson
shows how to cut, weld, and grind a pan for a seamless repair that will
give a factory look without using the full pan. This method will also be
easier due to less welding and grinding.
Sponsor: National Parts Depot
1981 Chevy 540 Big Block Camaro Project (Part 1)
This is my first attempt at rebuilding a car. This is my 1981 Chevy Camaro, I got it in 2004 and
drove her for two years before parking it in an outdoor storage lot while I
deployed to Iraq and then moved into a new home . After sitting outside for
three years I decided to strip her all the way down and build her the way I
always wanted to. I'm going for a ProTouring look and got my hands on a 540
Big Block. More project update videos to follow...
1969 Pontiac Firebird "Routy" Floor Replacement - V8TV
http://www.v8tvshow.com - Our 1969 Pontiac Firebird project "Routy" was a
pretty clean car to start with, but we wanted to improve upon some previous
repairs in the floor and trunk floor area. In this installment, we
replace the driver's side floor pan with a 1-piece replacement from Classic
Industries. There are tips in this video that apply to any musclecar