This is a Water Injection Test on a Civic Supercharged at 9psi
DevilsOwn Stage 1 kit using 100% of Water, no methanol or ethanol
No Water Injection: 42.7-88.0=47.3 C
Water Injection DO1 after (89cc/min): 38.4-81.0=42.6 C
Water Injection DO2 before and DO1 after (267cc/min): 33.3-70.4=36.8 C
Water Injection DO4 before and DO1 after (446cc/min): 34.8-50.4=15.6 C
Fluid MotorUnion E90 Dyno w/ Water-Meth
This video is a fun one, meant to showcase the method by which we inject
water-methanol into the intake on our project E90 M3.
The system is an Aquamist HFS3 system, modified with custom nozzles and
delivery pieces put together by Howerton Engineering.
Enjoy the sights and sounds :)
How Water/Methanol Injection Works & How It Makes Horsepower in Gas Engines
AEM Performance Electronics explains how Water/Methanol Injection works in
gasoline engines, the benefits of Water/Methanol Injection and dispels some
myths of using Water/Methanol. Water/Methanol works differently in diesel
engines, so stay tuned for a video on how Water/Methanol Injection works in
a diesel engine soon!
700+bhp STREET RX2 water injection specialist
RICE RACING developed Mazda Capella (for JSR racing)
RRWEP110 WI kit
700+bhp engine on pump petrol and RR water injection!
27+psi set up
Summerants 13B record setter
RR special rotor set
RR apex seals
Only 13B to register such power and still drive home (NOT ON A TOW TRUCK!)
Australia's FASTEST street 13B car, proven at Australia premier Dyno competition.
Filmed by RICE RACING taken from www.riceracing.com.au
WATER INJECTION SPECIALIST
Mustang 5.0 Vapor injector
An extremely cold and foggy winters day and a homemade vapor injector on a
5.0 Mustang produces
fantastic tailpipe Exhaust vapors.
Makes for a silly test and good fun. The vapor injector cost about 3
dollars to build. Allows you to run more timing, a cooler intake, and less
GT 40 heads-Comp cams valve springs-70mm throttle body-255lph fuel
pump-ported intake-power pulleys-Flowmasters
MKV GTi Water/methanol Injection
Selling the car: http://www.golfmkv.com/forums/showthread.php?t=177715
THis is a video showing my homemade w/m injection system. Its basically a
rough draft, and theres still a few kinks to work out, but it still work
2007 VW MKV GTi
-APR 93 octane tune
along with this w/m injection system.
The pressure switch is set to turn on the water pump at 8 psi. THe injector
size is a 4gph nozzle (from Devils Own). The pump is a 150 psi Shurflo
water pump. The gains are really amazing, in both HP and torque. The car
pulls from anywhere on the RPM band. Soon I'll GTec Pro some results and
make another video.
- Obey all Traffic laws, I am not responsible if you drive bad on the road
- Make sure you know what you are doing if you decide to make and install a
w/m injection system on your own. If you screw up, I'm not responsible.
- Driving parts of this video were filmed in a closed course.
D16 Civic Supercharged
Chipped P28 Tuned with CROME (crappy tune, running rich!!)
D16Z6 stock internals (block and head), Stock Map Sensor, Denso 460CC
Injectors, Jackson Racing Supercharger
at 6PSI, Walbro 255LB Fuel Pump, 4-2-1 Megan Header, 2.5 full Catback Exhaust
Water/Alcohol Injection for 7.3 idi non-turbo
In the never ending quest for better mileage and more horsepower, while keeping Exhaust gas temperatures low, Henry the
Hydrogen Ford gets a homemade water/alcohol injection system to complement
his recent ram-air/cool-air induction install and the massive HHO system
already installed. My (perhaps unobtainable) goal is 25mpg. Wish me luck...
Pre-compressor water injection
Video taken 18" from the inlet of a Holset HX35 being injected with water
at roughly 170 psi (250 psi pump) with a 7gph nozzle. It begins injecting
at 51 seconds into the video.
Pre Turbo Water Injection - Explained
Skip to the halfway point if you understand the basics of combustion. Or
enjoy my non technical explanations. Then learn about why I inject H2O
into my turbocharger's face.
Water injection kit by wannaspeed.com