2004 GMC Envoy XUV
Hello and thanks for looking at our auction! Up for your consideration is
this beautiful one owner trade Envoy XUV. This is a rare model. I
searched online to see just how rare it was and found that there were
approximately 25,000 of them made. That may sound like a lot to some, but
in the scope of things, it's not! This was a one owner local trade in that
is in PERFECT condition. One tiny rock chip on the front end that has been
touched up. Tires are at 80% all around. Brakes are tight, alignment is
perfect, tires are balanced , AC blows cold and the heat comes out hot!
Every option works as it should. As seen in the video
(http://www.youtube.com/watch?v=ON1cas1jmM4) it looks, runs and drives
great! You can bid with confidence. You could fly in and drive it 1500
miles to your home with no glitches. The back in seals up tight to you can
wash it out in the event you get it really dirty hauling stuff. When
winter comes, rest assure that you have your four wheel drive to assist you
as you make your way though town. All around this is a great vehicle.
Don't let it slip away! Make sure you click the free CarFax at the bottom
of this ad!
I6 ENVOY FLOWMASTER44.wmv
VIDEO OF MY ENVOY AFTER I INSTALLED A FLOWMASTER 44. i HAD MANY PEOPLE
ASKING ME TO TAKE VIDEO/SOUND CLIPS OF IT....SO HERE IT IS
2003 Mazda Front Wheel Bearing Replacement (Press In Type Bearing)
Wheel bearing replacement in a 2003 Mazda Protege 5. Press in style
bearings done without using a shop press. Specific for Mazda Protege, but
many of the techniques will apply to vehicles with pres-in-style wheel
It's a good idea to try to use the bearing-press-kit the way it was
intended. If the bearing doesn't budge, BE CAREFUL using a breaker bar. The
bolt supplied with the press-kit is not very strong...it with probably
shear off the head. Try to give the bearin a few hits with a sledge hammer
as seen in the vid..it will get the bearing moving. Then you can use the
press-kit, and it should finish pressing out the bearing.
Pressing in the bearing with the kit should be no problem.
Test Drive: 2006 GMC Envoy Denali
In this video, we take a test drive of the 2006 GMC Envoy Denali. We take
the car through the neighborhood and highway while displaying some notable
features from the passenger seat and the rear-seat perspective.
2005 GMC Envoy Walkaround
This is a walkaround of my 2005 GMC Envoy. Mods included are as follows:
Port Matching; K&N Cold Air Intake; Magnaflow HighFlow Cat; Borla CatBack
Exhaust; AirRaid TBS; PCM4Less Tune;
Royalty Rotors; Hawk HPS Brake Pads; Bilstein HD Shocks; Hotchkis Rear Sway
Bar; Chrome Mirror Covers; Street Scene Grille; Chrome Envoy Badge; FM
Antenna Removal; Anzo Black Taillights; Putco LED Taillight Bulbs; GMC
Hitch Cover; Goodyear Fortera SL's; 20" SS Wheel's; Range Rover Side Vents;
HID 6000 Low Beams; HID 6000 Fog Lamps; Painted Front Calipers; Tinted
Front Windows; Street Scene Front Valance; Rain-X Repel WiperBlades; Kicker
10" Solo Baric's; Pioneer AVIC Z2 NAVI; Boyo License Plate Cam; Escort
9500ix Radar; Viper 791XV Alarm/Start. Hope you enjoy!!!
Dodge vs. GMC vs. Nissan at Spring Creek
Dodge, GMC, and Nissan compete on this small hill climb (100% grade) at
Spring Creek Off Road. very muddy and slick; who will make it up?
Dodge and GMC are on Nitto Terra Grapplers. Nissan is running Michelin LTX
A/T2. The Nittos on the Dodge are old and bald; the Nittos on the GMC are
nearly brand new.
How to Change A Car Wheel Hub Bearing - Timken 513188 Pro 29513188 713188
Chevy trailblazer wheel bearing replacement DIY how to .. Wheel hub bearing
replacement 2003 2001 2000 2004 2005 2006 2007 2008 2010 2011 2012 2013 how
to install repair replace ... How to diagnose a wheel bearing .. Buick
Rainier . Ssr . Gmc Envoy . Isuzu Ascender , oldsomible Bravada , Saab 9-7x
. Moog 513188
How to Change a Wheel Bearing (short and fast version)
This video shows how to change a pressed bearing in a Ford, specifically a
95 Ford Windstar, but this method will be similar for all pressed bearing
vehicles. The main steps are to take off the spindle nut, tire, brake
caliper, and rotor. Then remove the bolts from the lower control arm ball
joint, tie rod, and strut. Remove the steering knuckle, then press out the
bearing and hub/spindle. Then press in your new bearing and hub/spindle.
This job is a little more complex but can still be easily done by any
amateur mechanic. You will save $400-800 depending on your vehicle. Pleas
comment, like and subscribe if you liked this video!
how to remove a pressed front bearing, how to remove a front bearing, 2003
Mazda Front Wheel Bearing Replacement (Press In Type Bearing), How To
Remove Pressed-on Bearings - EricTheCarGuy, Wheel Bearing Removal with
Harbor Freight Universal Tool BMW 325i Rear Front, bearing, press, pressed,
pressed bearing, front bearing, front wheel bearing, diagnose, how to, diy,
ford, windstar, ford windstar, Pressing out a front wheel bearing, harbor
freight, bearing kit, How to: Remove & Install A Truck Hub Bearing Assembly
with Timken, How to remove a rusted wheel hub bearing assembly the easy
way, trick, mazda, ford, lincoln, gm, truck, van, car
Due to factors beyond the control of ChrisFix, it cannot guarantee against
unauthorized modifications of this information, or improper use of this
information. ChrisFix assumes no liability for property damage or injury
incurred as a result of any of the information contained in this video.
ChrisFix recommends safe practices when working with power tools,
automotive lifts, lifting tools, jack stands, electrical equipment, blunt
instruments, chemicals, lubricants, or any other tools or equipment seen or
implied in this video. Due to factors beyond the control of ChrisFix, no
information contained in this video shall create any express or implied
warranty or guarantee of any particular result. Any injury, damage or loss
that may result from improper use of these tools, equipment, or the
information contained in this video is the sole responsibility of the user
and not ChrisFix.
Toyota Land Cruiser vs. GMC Envoy
This is a really funny match up between a 2003 Toyota Land Cruiser and a
2004 GMC Envoy. These trucks were both heavily modified to say the least.
The Land Cruiser had an off road setup, while the Envoy had more of a show
car setup. This is not one you see everyday!