350 v8 go cart first run burnout
This is in Kelowna BC CANADA
cookin off tires on our 5L
https://www.youtube.com/watch?v=dbHiZWEflOE&list=UUV9Q4t4eKsqfRhPB0on6l2g&index=1
after this video we did weld rear end, put in a throttle pedal, a tach, then jumped it, split the bell housing and blew it up :)
Twin Turbo 383 '71 Nova
Chevy 383 in a '71 Nova with twin Precision T-61 turbos, the parts list is in the video. The Intercooler is not hooked into the intake system in the video for simplicity reasons. Enjoy!
Mazda Rotary Dyno Massive 1664HP
http://www.braptv.com
This engine has massive HP, WOW Awsome also on braptv.com Mazda Rotary Queen Street Racing 4rotor GT60 1664HP
TWIN TURBO 1971 CHEVELLE OVERVIEW AND DRAGSTRIP RUN
Overview of custom twin turbo setup on 350 cu-in small block chevy in 1971 Chevelle. Divided housing twin scroll Garrett T04B twin turbos on custom schedule 40 thickwall divided tubing manifolds. Dual turbonetics Deltagate wastegates and HKS blow-offs on custom intake plenum. Carb Shop prepped Holley 750HP for blow-thru applications. Good low end throttle response with minimal high end power loss. 525HP at the crank with 8psi Boost and no Intercooler. Dragstrip run at end of video shows stock 2002 BMW M3 running a 13.78 with a good launch. Chevelle was eased off the line due to too much torque and still ran a 12.50
CHECK OUT MY OTHER VIDEO OF AN IN CAR DRIVING EXPERIENCE
SEARCH FOR "CHEVELLE TWIN turbo IN-CAR"
69' Camaro 500+ HP HAND CRAFTED Motorsports Edition by Alex Zaric
Created By Alex Zaric. This custom hand crafted 69' Camaro is the ultimate in racing performance and hand crafted styling. For more info contact
http://azrmotorsports.com
Photography and video by James Michael
http://jamesmichaellang.com
Chevy 383 Stroker 650 hp
First time cranking the beast.AND THIS CARB WAS SHIT SO I REPLACED IT I WAS ONLY USING TO TEST AND TUNE WHILE ON THE STAND- Engine Contents:
BRAND NEW DART 4 BOLT MAIN BLOCK
Heads - Dart Pro 1 Aluminum series CNC PORTED 320 CFM
Carburetor - QUICK FUEL Q-950 RACE SERIES CARBURETOR
Distributor - COMPLETE MSD DISTRIBUTOR SYSTEM WITH AL6 BOX AND COIL with 3 step and crank trigger
Hooker Super comp headers Ceramic coated
Intake Manifold -Team-G High rise intake CNC port matched
Fuel Pump - 400 GPH HIGH VOLUME Holley
Water Pump - CSR electric
Valve Covers - CUSTOM Chevy engraved and clear coated
Wires - MSD PERFORMANCE WIRES
Spark Plugs - NGK PERFORMANCE
Forged Pistons -J&E FULLY FORGED PISTONS
Forged Rods -Manley Push Rods
Crankshaft - Callies Magnum 4340 FORGED 3.75" STROKE CRANKSHAFT
Rod Bolts - ARP
Roller Camshaft - COMP CAMS ROLLER CAM
Valve Springs -Manley Nex Tek Triple Valve Springs w/ Titanium Retainers
Hydraulic Roller Lifters - COMP CAMS ROLLER LIFTERS
Double Roller Timing Set - PRECISION TRUE ROLLER
Timing Cover - CHROME GM PERFORMANCE BOWTIE
Head Bolts - ARP stainless
Flexplate - SFI PRECISION
Harmonic Balancer - ATI Performance Products SFI Rated Balancer
Jeep V8 Chevy 350 MegaSquirt2 and MegaTune
This is another video of my 4 bolt chev 350 in my YJ. It is using an rv cam with cast manifolds and a wide open 18" but surprising quiet magnaflow. The TPI is from a 1992 vette (advertised but probably z28). 255 gal/hr Walboro pump, pro comp long water pump, I rebuilt a turbo 350 tranny and don't need a slip yoke eliminator because even with a little 2/5 inch lift my drive angles are awesome (the turbo 350 has a lower output). Also, an Advanced Adapters crossmember and a Novak t-case-tranny adapter plate and mount bracket are used with a stock GM rubber mount. My home-made wiring harness needs clean up and I have a new big block chevy conversion rad on the way. A nice ride!
one badass sbc chevy 350 2008
1/18/2013
I'm not building 350's anymore
I build strickly 383 chevys with all new parts no more rebuilt or used blocks and heads
I start with a new dart block and new pro aluminium heads I have 4 different packages stage 1 stage 2 stage 3 stage 4 and stage 5 between 375 HP - 555 HP your choose all between 5000 - $ 6800 dollars shipped to your door if your with in the 48 states.
heres a pic/video of the motor i had for sale..it is now sold and runs 11.85 in the guys malibu with a msd distributor different carb intake a lumpyer cam this video is for fun...and for all you engine builders out there the way it sits in the video she would do a good high 12 low 13 in a heavy car...you may think yours is better...but mine is all new top to bottom and costs a third to build compared to what half of you charge but for the real people that can appreciate it thanx for watching
SuperCharged BBC 468 Camaro Part 1
Just doing a few drive bys , first time video i know its shakey, Check out part 2 http://www.youtube.com/watch?v=4350R8rfBCo
