Mazdaspeed3 vs. H22 Turbo Accord
Mazdaspeed3 stock with CAI vs. a built and turboed H22 94 accord coupe. Accord has Darton dry
sleeves with eagle rods and wiseco pistons. t3/t04e ebay turbocharger, spoolin log manifold, synapse BOV
Accord email@example.com psi...running 10psi max in vid
Honda Accord SR '94 Turbo 270 w hp
Specs: Honda Accord 2.3 SR 1994
F20 motor with H23 head
act extreme stage 3 clutch (not good for hydrolic system!!)
Tcc light flywheel, h23 prelude gearbox
XSPOWER h22 turbokit. T3/T4OE turbo 8.7 psi, S-AFC 2 controller
Custom made header and downpipe. 450cc DSM injectors
AEM UEGO wideband + bosch o2 sensor
Car is sold, after 40-50.000km with this setup the engine stays running !
Good old times :-)
94 AccordT GT17 #2
Just a little short clip with side Exhaust. Right at about 15lbs. Nothing
spectacular. This is your daily driven 4 door family sedan. No Dyno runs yet! :(
Accord F22B turbo start up
Accord Start up at the storage unit. This is how i recieved the wagon,
running on 3 cyl. The car was built by a shop that hacked the car.
Link to the build.
How to Turbo - Part 1
After buying a Euro car last episode, Marty discovers he has not yet found
his perfect vehicle... In this extended episode, we reveal what he got, and
show how to make it faster.
Wanna show the world that you fix your own shizzle? MCM stickers, ti shirts
and other mad shizuoika available here:
Official Site: http://www.mightycarmods.com
Music from the episode is available here:
http://www.mightycarmods.com/collections/music (Forced Induction by MOOG
was featured in this episode)
Also something to note around Mighty Car Mods: we are normal guys and are
not trained mechanics. We like to make interesting car mods and show you
how we've gone about it, but we can't promise that anything we show you
will work for your particular car, or that you won't harm yourself, someone
else, your car or your warranty doing it. Please be safe, be responsible
and unless you know what you're doing, do not fool around with very serious
machinery just because you've seen us make it look so easy. Talk to a
qualified mechanic if you are in any doubt.
How To Pull Honda Codes Without a Scanner -EricTheCarGuy
Link to code explanations:
Honda ABS Codes 1994-1997:
Honda ABS Codes 1998 and up:
Visit me at: http://www.ericthecarguy.com/
Discussion about this Video:
I feel like I should have made this video a while ago but the opportunity
never came up. Since I had this RL in my shop that had a check engine
light AND an ABS light I thought it was a perfect opportunity to put this
video together. I get asked all the time about my 'special tool' and it's
really nothing more than a Honda 2 pin connector with the input wires
soldered together. These connectors might be harder to find than you think
but if you run across a junk honda and one of these is on the harness grab
it. Even if you don't have the tool a paper clip or piece of wire will do
the exact same thing so don't sweat it if you don't have the tool because
shorting the connector is all you need to do.
I hope you find this video helpful.
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
P2646 Honda Accord ,VTC strainer
P2646 Honda Accord ,VTC strainer. This Honda would not run at higher
speeds. It would start bucking and stall out if held to the floor. After a
bit of cleaning it seems to run fine. Do not try just removing the screens.
If you try to run a Honda with out the VTC strainer any dirt that the
screen would of caught will now go in to the little oil passages and be
hard to remove. I am also Leary of trying to add cleaners to the engine
when experiencing VTC Strainer problems.If the debris stuck in the VTC
Strainer bad enough to set a P2646 code then I would be afraid the debris
would break down smaller ,get through the VTC strainer just to get caught
up in the valve train oil passages.