Saturn SL2 Valve Cover Gasket Replacement (DOHC)
This is a long one, Sorry, but it pretty much goes through the step by step
and shows some of my mistakes so you don't make them.
Also, verify that the gasket fits. If you have the time then I would
suggest bringing the valve cover in with you(assuming you bought it from a
local parts store) and make sure it fits before leaving. I must have gotten
one from a bad batch because the first one was too big. You will see that
in the video. The second try was the right(ish) one. apparently it is a
known problem that the molding process is incorrect for these gaskets but
luckily they are rubber so you can just remold it to fit.
Good Luck and Hope this helps you save some money. Spent about $60 total
doing this in tools and parts.
TURBO SATURN PROJECT DRIVING AROUND TOWN
Just a little portion of running around the city. Like finding roads that
are long and straight and just opening up. Watching this vid you can see
the Boost gauge in the lower right
corner. After watching at home later, I noted my Boost is dropping from 10psi to 7psi at higher
rpms. I'm currently hunting to find the problem. Once I do, I'll have 10psi
across the board, lean out high end rich mixtures and get to 120 mph
Instrument Cluster Light and Domelight Replacement/ LED Conversion on 98 Saturn SL2
This video was a fun one to do. You can use this as a video on replacing
the standard bulb that goes into the socket, or you can replace them with
LED's! Recently ran across a few threads on a popular forum for Saturns
about putting in LED's. Thought this was a good idea. I got my bulbs from
superbrightleds.com. Below are the part numbers:
74-CWHP3 Mini Wedge Base - for the instrument cluster
RL4410-CWHP9 Rigid Loop Festoon - Domelight
I kind of skipped over the removal because there was another video already
made. Props to Richpin06a for a great instructional that helped me. link
for his video is below:
I am piggybacking off his video to show the light replacement on the
This might be long, but I hope you enjoy it.
Thanks for Watching!
Pimped Out Saturn SL2 *UPDATED*
NEW: just got a body kit! its installed but has a few fitment issues that
need figured out. looks sweet, but needs some work before its done!
also did the "Flip Flop" trunk mod, took out some of the carpet, cleaned
things up. always messin around with this thing
check out my page: http://www.cardomain.com/id/courtlife
*NEW 18" Konig Uknowns with Kumho spt tires (for the summer)
*removed the bar across the "grill" and the front license plate - looks
*swapped the subs and Tv's because of trunk rattle & tailgating purposes
*Redone carpet in the trunk/back of the back seats
*Black Saturn Emblem
*Sony Door Speakers
*Saturn Racing Team decal on windshield
*Painted Calipers and Drums black
*Repainted the dash Silver
*Painted the molding above the windows black
*Weapon-R cold air intake
*Chrome Exhaust tip
*Switches installed on dash for Amp and power inverter for PS2 & tv's
*2 12 inch Type R
*Q-Logic Ported/Sealed Box
*2 15 inch Sony TV's
*Power Acoustic PTID-6500
*150 Watt PA System (Speaker is OUTSIDE)
*Blacked-Out Taillights and Side markers
*Sony Playstation 2 in the trunk
*5 % tint
*Bulldog 200 Deluxe Remote Start
All installation was done by myself, including remote start and tint job.
Any questions or comments are appreciated!
Saturn Idle problem.mov
In this video we show you how to replace an idle air control solenoid and
clean the throttle body on a 1996 Saturn. This car was having a
excessively high idle. It would stay at 1500 RPM even though your foot was
not on the gas pedal. This was caused by carbon build up around and behind
the throttle body as well as a defective idle air control solenoid.
Jonesy's Auto Club videos are for reference and entertainment only and
should not be taken as a direct step by step guides. If you attempt a
repair like the one seen in this video please use the proper safety
equipment, take your time and do the job right.