Zakspeed Ford Turbo Capri
Zakspeed Ford turbo Capri beim AvD
Oldtimer GP 2012 auf dem Nürburgring. Peter Zakowski fährt das Original
Meisterschaftsauto von 1981, mit dem Klaus Ludwig damals gewann.
Das Fahrzeug ist mit dem kleinen Motor der Division 2 bestückt mit 1,4l
In beiden Rennen sah Zakowski die Zielflagge wegen technischer Probleme
nicht. Im Rennen 1 bedrängt er Oliver Mathai im Porsche 935 und im Rennen
2 räumt er binnen kürzester Zeit das Feld von hinten auf.
Sowohl nach dem Training als auch nach dem ersten Rennen wurde am Fahrzeug
umfangreich gearbeitet. Der Ladedruck ist noch nicht eingestellt und
deshalb hat P.Zakowski die Hand häufiger mal am "Dampfrad".
Vom turbo Capri wurden insgesamt fünf
Fahrzeuge gebaut. Ein Fahrzeug wurde zerstört, eines zu einem Mustang umgebaut, ein Fahrzeug wurde
von Herbert Stenger bei Bergrennen eingesetzt, ein Fahrzeug baut Stefan
Mücke in Berlin wieder auf und hier eben das 1981er Meisterschaftsauto bei
onboard race1 at 05:35
onboard race 2 at 12:14
2.2 Ford SOHC pinto Engine with open pipes - Mk1/Mk2 RS2000 Escort/Cortina Kitcar
2.2ltr ford sohc 'pinto' engine
offset ground crank, diesel rods, cologne v6 cast alloy pistons, teflon
buttons, Burton power rings, stainless steel one-piece inlet & ex., valves
(44.5 & 38mm respectively - wasted stems and inlet seat further narrowed).
Epoxy resin used to improve shape of inlet port - 'Apple port' as per David
Vizzard book specs.
2x Twin 45mm Dellorto DHLAs with (If I remember correctly) 38mm Chokes.
Infact, the specs I followed are available in Des Hammill's book 'How To
Power Tune Ford SOHC 'PINTO' Engines. He gives several examples of motors
including 2-3 set-ups for Pinto engines including 2100cc which is the one I
used. It got the results you see above.
Cylinder Head work has been elaborate and very time consuming (Valve guides
have been ground flush with the roof on both inlet and Exhaust ports).
Exhaust ports enlarged throughout. -
Both in. & ex. throts have neen 'throated' and then blended in upstream
with the rest of the port.
Heavy duty bearings all around including camshaft.
Standard ford factory camshaft & springs used during this video.
Standard points type distributor etc etc..
Mechanical Compression approx 10.8:1 (I used 100octane shell V-power
petrol for my runs).
Standard flywheel had all the available mass machined off to give the
lightest possible unit whilst retaining the most of the strength. It has
five steel dowel + 6x ARP bolts fastening it to the crank.
Crank was machined at halesowen engines (Don't think they do it anymore as
old man retired) then heat treated at laystall crankshafts in Wolverhampton
(different trading name now I think) and also polished at laystall
Diesel rods have seen some machining to get them to fit the crankshaft
(Rods are thicker and longer + a little hevier when standard).
Rods fitted with ARP YB cosworth rod bolts (No nuts).
I spent the best part of 7 years building this engine.
It has been a financial disaster and I would not do it again.
Saying that however, the value of building and running the engine
successfully will most likely reveal itself as the years go by.
I'm pleased you like the video and wish you great results with your
(Dedicated to my uncle).
2005-2013 Stourbridge (UK)
Cam and Crank Bolt & Washer Set link:
2002 Dodge Ram 1500 Engine Swap 4.7L Part 1 - EricTheCarGuy
Link to full version of this video:
Link to part 2: http://www.youtube.com/watch?v=QES-WrAB1NI
Visit me at: http://www.ericthecarguy.com/
This truck has been a challenge for me over the past couple of weeks as you
will seen in the video. The lesson here is do your best to check the
engine out before you install it and even that may not be enough. Be
careful when doing a job like this especially if you are by yourself as you
can get seriously injured if your not careful so work carefully and
methodically and things should work out fine.
The music is from the site
under "Royalty Free Music", it's title is "Merry Go-Distressed", the
producer of the site allows the use of this music as long as credit is
given, hence the credit given here. Thank you!
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
Visit my Facebook Page:
Be safe, have fun and stay dirty.
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
Capri RS 2600 Cosworth V6 dyno crash
See more at https://www.facebook.com/CapriRS2600
Partial throttle runs for fuel mapping. Dyno was set to sweep
1000-7000rpm in 18 seconds. Limiter at 6450rpm. Crash at 5400rpm most
likely due bad conrod bearing.
Highlights of season 2013:
Flits Engine Swap Honda Civic d16 to b18
Uploaded again, this time with freeware audio to prevent Youtube from
blocking the video because of copyright issues.
A timelapse video swapping a Honda Civic d16y8 to a b18c4
Before posting replies about the lamb-doors, I suggest that you check my
latest video first ;)
Test Drive the 1974 Ford Capri V8!
Hi! This is Agent 8771's 1974 Ford Capri, featuring a high-output 302 V8
and Borg-Warner T5 transmission hooked to a Ford 9 inch positraction rear.
This car originally had the wheezy Pinto 2000 cc engine and 4 speed trans,
so it is much better now. A nice, original, rust-free unit brought up from
the States to save it from the idiotic "cash for clunkers" stupidity. Sweet
vintage aluminum slot mags, nerf bars, and diamond-tuft package tray finish
this Capri off in classic 70's style! Hope you like it as much as I do!
Engine Swap Video
1997 Ford F150 Engine Swap
From a N/A 4.6L to a 2003 SVT Supercharged 5.4L