Keyless Entry Problem / Solution (GM Key Fob 22733524)
The unlock button on my new key fob quit working weeks ago. Thanks to
YouTuber trando2010, I found a quick and easy solution to this issue that I
had to try and share with you.
Here is his original video link :
GM Key Fob Fix (Works with many different fobs)
Made this video to show how you can cheaply and easily fix your key fob if
you have one or more buttons that no longer function. This fix works with a
TON of different fobs that GM uses, you can check the website that sells
these for a complete list of compatible vehicles/fobs. I am in no way
affiliated or employed by this company, I just had a dead button on my fob
that was driving me insane and this fix works like magic so I wanted to
share the knowledge.
Simply put, the buttons stop working due to worn carbon pads on the back
side of the buttons. These pads are what complete the circuit for whatever
function you want which then sends the proper signal to the vehicle.
Without a completed circuit, the signal is never sent, and the button
appears to be dead.
With the insert you can purchase from www.keylessfix.com you can restore
all your buttons to their proper working state. Simply pull your key fob
apart, remove the circuit board from inside, and place the insert into the
button cavity with the SMOOTH SIDE DOWN, against the buttons. Reassemble
the fob and all your buttons will now work.
There is another issue some may run into where ALL buttons stop working,
but this is very likely due to the battery holder detaching itself from the
circuit board. To fix this issue, simply resolder the battery holder to the
circuit board in the three locations it is attached with.
Hope this helps save you money on fixing a seemingly broken key fob for a
lot less than you think!
How to Program a GM Keyless Entry Remote Key Fob LHJ011
Programming instructions for GM Key Fob with FCC ID: LHJ011
GM Part # 21997127, 15132197 #1, 15132198 #2, 10377295, 22730827, 15186203,
15186200 #1, 15186201 #2
Check out http://www.ekeyfobs.com for great prices on replacement keyless
entry remotes and transponder keys.
You can purchase this item directly at
This procedure was carried out on a 2003 GMC Yukon but will also work for
the following vehicles
2003 2004 2005 2006 Escalade
2003 2004 2005 2006 Avalanche
2005 2006 Equinox
2003 2004 2005 2006 Silverado
2007 Silverado Classic Body Style
2003 2004 2005 2006 Suburban
2003 2004 2005 2006 Tahoe
2003 2004 2005 2006 Sierra
2003 2004 2005 2006 Yukon
2003 2004 2005 2007 Hummer H2
Ford Remote Key Fob Programming Instructions - How to
How to program a Ford Remote Key Fob brought to you by
These instructions will work for most Ford vehicles and for the 3 or 4
button version of the remote. We have these ford remotes as well as ford
transponder keys available at a fraction of the cost of the dealerships at
Here are the steps:
1. .Turn ignition from OFF to RUN 8 times within 8 seconds, with the 8th
time ending in RUN. Door locks will cycle to confirm programming mode. (Off
is the position where you can remove your key, RUN is the position just shy
of starting your car.)
2. Within 10 seconds press any button on the first keyless remote to be
programmed. The door locks should cycle to confirm that the remote has
4. (Skip this step if you only have 1 remote) Within 10 seconds, press any
button on the second keyless remote. Door locks will cycle again to confirm
programming. Repeat step 4. for all other remotes.
5.Turn ignition to OFF. Locks will again cycle to indicate end of
Car Key fob button repair
The video is about repairing Key fobs.
The particular key I am repairing is from a peugeot 406, but many citroens
and other peugeot model have the same or very similar case and the
technique used can be applied to many other car keys. Just dont over heat
The buttons on this case are actually bonded in place so a new key fob is
required to repair it.
The one I used was bought via an internet auction site for a few pounds
I created this video with the YouTube Video Editor
Program keyless entry remote for GM / Chevrolet / GMC1998-2006
If you get a new keyless entry remote (key fob) or change the battery in
your remote you may need to reprogram your vehicle to accept the remote.
This procedure works for a lot of 1998, 1999, 2000, 2001, 2002, 2003, 2004,
2005, 2006, 2007, and some 2008, and 2009 GM (Chevtolet and GMC) vehicles.
See below for vehicles that the procedure should work on.
Thursday, August 02, 2012
Suburban/Yukon 2000- 2006
Blog post here:
Another resource to find instructions: http://www.programyourremote.com/
GM Dash mounted Ignition Rekey
Another Delima: 2001 Chev, Monte Carlo: Dash-mounted ignition lock
cylinder rekey. Equipment, tools, procedures, safety, key code location,
security, vehicle theft detterent system components (intro/identify).
There are many roads...but this one is mine. Thank God for the opportunity
to be of assistance. Enjoy.
General Motors' EN-V concept - we ride shotgun
TheChargingPoint.com recently got a ride in GM's incredible EN-V concept,
designed to combat the problems of overcrowding, parking availability and
air quality within the city of tomorrow.
Read our report at
Music credit: danosongs.com
how to unlock a car without a key
how to unlock a car with a tennis ball.
This is fake. Yes I know. Please stop contacting me about it. Noticing
it isn't real doesn't make you some kind of genius; it's obvious. If you
think you're clever for figuring it out, you're not. In fact, you're a
damned moron for not realizing that EVERYONE figures out this trick.
I uploaded this video just to try uploading a video, I never meant for it
to get over a million view.
God damn. Youtube really is full of morons.
Edit: Made this crap easier to read for you idiots.