1971 Pontiac Ventura II like Chevy Nova For Sale
http://www.sdscad.com/pontiac/ventura.htm 1971 Pontiac Ventura II No rust
2nd owner; Super low miles! 68,000 New fuel pump, radiator, master
cylinder, brakes; New Muffler, Pristine running condition! Stored for 17
years, all original equipment body perfect
Tony Bromley's 400 to 460 stroke Pontiac Dyno Pull | QMP Racing
550 torque @ 5800rpm
535hp @ 4000rpm
For those of you paying attention and noticed the numbers aren't the same
on the screenshot, its because we made another few runs, but didn't tape
them. We'll upload a pic soon.
QMP Racing is located in Chatsworth, CA
Check out our website: www.qmpracing.com
Like us: facebook.com/qmpracing
qmp racing quarter mile race car engine motor custom high performance
chatsworth California hp horse power torque trq Dyno rpm turbo drag Exhaust run Boost psi dragster raceway nitro Nitrous super Supercharger muscle burnout idle motorsports Mustang cam Ford hydraulic
Street pontiac Cars Supra "Drag Racing" Pontiac Shelby Dodge Twin Stock
Mazda Ls1 Motorcycle Bike
Pontiac Banshee A Longer Look
The Banshee was a vision for what the Firebird could become. Of course,
this concept car could never be built exactly, too low on the road and it
wouldn't pass the safety and crash tests, but it was exciting. It
demonstrated that the problem with GM cars didn't sit on the designers'
shoulders. They were more than capable of dreaming up engaging and fun
vehicles that would set imaginations on fire.
PONTIAC - "The Super Duty Story" Part 1 of 3
Pontiac had an SD engine program in the late 50s early 60s, and
later/briefly again in 1973/74 with the SD455. This video is regarding the
FIRST Super Duty program.---In only a few years time during the late 50s
early 60s, Pontiac MORE THAN DOUBLED their V8's horsepower output (described
in this video), while using/keeping the same V8 engine block they used thru
1955-81. Even though the same block was kept, from 1955-62 the cubic inch
displacement grew much larger than the initial 287 cuber it started as in
1955. It grew to a 317 347 370 389 and finally a 421 cuber in 1962. It
eventually maxed out at 455 cubes in 1970. By 1970 ALL the other GM
divisions were producing engines at 454 or 455 cubes (500 for Cadillac).
PONTIAC WAS THE ONLY DIVISION still using the same block they used in the
1950s on engines that had a much smaller displacement -- 287 cubes. The
1955 287 displacement would remain the smallest displacement ever used in
the Pontiac V8 block all the way until 1980/81 when a 265V8 was produced.
Since less durability was required for the smaller displacement, the block
was decked/butchered/lightened on the 265/301v8s of 1980/81. Prior to 1980
the block had never been decked/butchered/lightened. The 1980/81 265/301v8
blocks were about 200 pounds lighter than the 1955-79 blocks, and only 25
pounds heavier than a Buick 231V6.
1961 Pontiac Ventura Bubbletop
Really a nice car. I've never seen one except in mags. This be a rare
'61.since I've never seen one before in my area. Has the look of a high end
Pontiac Ventura - Pontiac Grand Ville
THIS VIDEO IS FOR EDUCATIONAL PURPOSES ONLY UNDER THE FAIR USE ACT.
Copyright Disclaimer Under Section 107 of the Copyright Act 1976, allowance
is made for "fair use" for purposes such as criticism, comment, news
reporting, teaching, scholarship, and research. Fair use is a use permitted
by copyright statute that might otherwise be infringing. Non-profit,
educational or personal use tips the balance in favor of fair use.