1971 Chevy Nova drag car for sale 509 c.i. roller big block over 750 hp 6.03 1/8 mile 2800 lbs

Here is Mr. Hensleys 1971 Nova drag car for sale. Best time 6.03 in 1/8th mile. 509 cubic inch roller big block with Dart heads, 9" nodular rear with 4.88 gears (rear will take up to 2500 hp). 400 turbo with manual valve body, air shifter, and trans brake. Weld wheels. Pro built, solid and dependable. Straight body and beautiful paint/graphics. Steal this car for $15,900. UPDATE. CAR IS SOLD! THANKS!

More Videos...

1970 nova drag race for sale and trailer
my husband is selling his nova and trailer and wanted one last look

10 second pro street green chevy nova run in street trim
1972 chevy nova street trim small block 406 no nos ever.stock suspension small tire car 275 -60- drag radial.3450 lbs with driver .Pro Street show and bracket drag car nhra joliet route 66 pro track champion.2008 super chevy winner Key words for searching are .Byron dragway union grove Da grove, us 41 drag strip chicago street racing wheel stand contest

Wicked 1969 Chevy Nova, burnout and launch
Wicked 1969 Chevrolet Nova burnout and launch. Fontana Super Chevy bracket races. Courtesy of ThermoCap

Ken Jones - 69 Chevy Nova 383 - Launch Street Radials 2
Before the nova was painted (black) and restored 383 Stroker: (633hp/577tq @ fly) 1969 Original SS 350 Block - 4 bolt main (3970010 cast numbers) - block had been resin filled for strength Eagle - 4340 Forged 3.75" crank (this is an actual 383 specific crank, not a 400 crank milled down to a 383) -Knife Edged and Lightened Eagle H-Beam 4340 Forged Rods (6" rods) JE 4340 Forged Pancake Pistons (full floating pins and Nitrous reliefs) (11:1 Compression = Runs just fine on 91 octane pump gas, but loves 103 octane) - Pistons were Ceramic Coated for Nitrous but nitours has never been run on it. (been wanting to but never got around to it) 64cc Edelbrock Performer RPM Heads (Aluminum) -Fully ported and port matched to the intake and Exhaust -Valves Sizes increased from 2.02/1.60 to 2.08/1.60 -Rev Kit / K-Motion Springs -Comp Full Roller Rockers Holley Strip Dominator Intake Manifold -Port-matched to heads Holley 830cfm Mechanical Double Pumper Carb (re-jetted with jet kit included) -fuel pump is mounted right next to the Fuel Cell and is fully plummed with dash 8 AN fittings and dash 8 steel braded fuel lines. All Transmission lines are done the same way as well Iski Cam - Solid Roller Cam - .602/.602 lift 300/300 duration with 1.6' rockers = .642 final lift Ignition: MSD 6AL Box with changeable rev limiter chips MSD Distributor Griffin 2 - 1 inch core radiator Black Magic Electric Fan Remote Trans Cooler with onboard electric fan Entire assembly has been blueprinted, matched and balanced to each corresponding part. Exhaust: Hooker Supercomp Headers Dual 3" Tubes Dual 2 Chamber 50 Series Flowmasters (this setup sucks... get the Borla XR1s instead) Drivetrain: TH 350 Manual Valvebody Race Transmission Beefed up Driveshaft by Whittier Driveline 3.73 gears with a mini spool in video, then switched to 4.56 minispool, but that was too much, now its got a 12bolt posi 4.11 Heat treated axles Rear-End was a 10-bolt (sucks..) now 12 bolt. Multi leaf springs and lift bars 4000 Stall with anti balloon plates for Nitrous