Ford Powerstroke Faulty Injector Wiring Harness
A faulty injector wiring harness on the driver's side cylinders of the
engine caused the engine to run the way it did in this video. I replaced
both wiring harnesses in case the other one failed. I also replaced all
eight glow plugs while I was at it. Runs perfectly now.
How Oil Pressure Works - EricTheCarGuy
How Oil Pressure Works - EricTheCarGuy
Here is the second offering from last weeks set of videos. The most
important thing to note with this is that oil pressure is not created by
the pump but rather the resistance to the outlet flow of that pump and part
of that resistance is the clearances between the bearings and the other
parts inside the engine. If nothing else I hope you are entertained,
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
Visit my Facebook Page:
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.
Engine Running NO OIL - NO SUMP - Seized Soild on Camera
Messing with a Mitsubishi Lancer
There are loads of videos where people run an engine at full rev with no
oil in it, and the engine seizes.
Running it a medium rev, I wanted to see how long it would run with no
lubrication, and I was surprised.
However if the car was driving and the engine was under load, it would be
dead in minutes!
Mercedes Million Kilometer Test
Mobil 1 put 1 million kilometers on a Mercedes-Benz engine then broke it
down to see how the fully synthetic motor oil did in leaving minimal
deposits and minimal wear on the engine, demonstrating how Mobil 1 will
allow an engine to operate in like new conditions through an extended test
Cash for Clunkers: How to destroy an engine.
This is a video document showing how to seize an engine under the Cash for
Clunkers program...After draining the engine oil the vehicle is filled with
approximately two-three quarts of salt/water/silica mix. The vehicle is
then started and ran till the engine seizes. Enjoy!
Supercharged home made Straight Eight by Desperate Dan Vid 2
Built in a shed, it fired up first go. I was hoping it would sound real
lumpy like a drag engine, but it runs too smooth, and it's too quiet even
with unsilenced 9" pipes! The timing was a pain to sort out the Rover
distributor runs backwards, I had to take the heads off to work out the
firing order!!! See the shed it was built in on Vid 1.
Added May 2012: OK, my nails are dirty, maybe because I'm an engineer &
build stuff? Maybe your nails are clean because you can't build eff-all &
just sit behind your computer? C'mon folk, get a life.
Volvo 855 - Eats stones and chocolate milk.
▀▄▀▄▀ ASFALTSELITEN.COM ▀▄▀▄▀
Volvo 855 with Per and Freddie.
Our Volvo needs feed. Stones, chocolate milk, wheelnuts is what it wants.
Våran volvo är hungrig! Då vill den ha sten, chokladmjölk och
Ricer Destroys His Engine
Download this video for free in ipod, psp, and avi formats right now from
Watch this ricer try to take on a BMW M3... Oh wait, what was that sound?
Boss 429 dyno blow up!
Boss 557 on Dyno when
everything goes wrong. Had to rush for Dyno time and did not have
billet flywheel. We used stock 429 flywheel. Made 6 runs, this was the
7th. 850 hp before the blow.
Evinrude 300XP -91
After a few hours in the workshop..
The expansion chambers are "home made" by hydroforming. The original Exhaust is milled away and the engine
block is filled whit plastic.
This engine will get electronic fuel injection and will not be used in a