2006 Pontiac GTO electric cutouts
My friend just installed Electric cutouts into his GTO.
http://www.jackthreads.com/invite/mtamborr
Click the link above to get sick clothes for mad cheap. signup is free and takes seconds. site is 100% legit so check it out!
GTO w open headers
Am working on my car... putting 3 " Exhaust on it... this is after I cut the old 2 1/4 sustem off.... getting it prepared for the new install....
MAKE SURE YOU CHECK OUT MY OTHER VIDS SOME OF THE GTO DRIVING IT AND MY PRO STREET VEGA
Burnouts open headers on the street
I am the announcer at Kansas City International Raceway.KCIR. This video was taken June 3rd. 2006 on a very busy 4 lane road that was just resurfaced and repainted, i think they did it just for me and a couple of hundred of my friends.It was called an open header cruise, where cars would cruise to Fuddruckers about 5 miles from the dragstrip. Then with the help of some friends we shut down the road for about 20 minutes until the police showed up.
1965 GTO with open headers 455 and a stick doing a Smokey Burnout.
(Turn it up!!) My 65 GTO in a warm up burnout at Big Al's '05 4th of July party in New Milford CT. Last one he had at his house. There was a car show, a burnout contest, a car smashing corral (usually a Jap car), good food, good people, beer and music. Will miss this party!!!
2006 Pontiac GTO - Cam, tuned and full exhaust
This is my 2006 Pontiac GTO with a 228 cam, JBA headers, full catless Exhaust with Flowmaster mufflers, lowered by about an inch, Harrop rear differential cover and several other performance goodies. 425whp and about 405 ft.lbs of torque.
1100rwhp GTO (Black Hawk)
Marks Workshop present a walk around and Dyno run on Tony's Black Hawk, a HSV GTO (one of Holden Special Vehicles versions of Holdens Monaro) This vehicle runs a built War Hawk LS Block running a Callies 4" crank to a 402ci, oliver rods, ross pistons, ETp LS7 port heads, etc, with a complete Marks Workshop custom Vortech V7 ysi OTR intercooled Supercharger system, MWS in boot custom fuel system, 2" headers and MWS custom 3.5" Exhaust system, a T56 with twin plate cerametallic clutch for Dyno and show duties and a built 4l80e for street duties. It has the monster Harrop brakes and Simmons 19" Rims. Custom front and rear clip hand made by Owner Tony
Custom work by Mark at Marks Workshop
http://www.marksworkshop.com.au/
link to build pic's http://www.marksworkshop.com.au/Pages/site%20project/project%20cobra%20ls7/cobra%20project.htm
link to article http://www.marksworkshop.com.au/Pages/feature/BLACK%20HAWK%20GTO.htm
SOME OF THE CARS ON THESE YOUTUBE VIDEOS ARE SHOWN IN A FORM BEYOND THE STREET LEGAL LIMITS FOR WESTERN AUSTRALIA. THESE CARS ARE USED FOR SHOW, TRACK OR OTHER OFF ROAD EVENTS. IN MOST CASES THESE CARS ARE TAKEN BACK TO STREET LEGAL LEVELS TO BE ABLE TO USE THE VEHICLE LEGALLY ON THE ROADS OF WESTERN AUSTRALIA.
MARKS WORKSHOP DOES NOT CONDONE THE USE OF EXTREME HORSE POWER ON THE STREET.
DRIVE RESPONSIBLY DRIVE SAFE
Marks Workshop
www.marksworkshop.com.au
20 maxwell street YORK W.A.
08 96412305
1969 Pontiac GTO Open Hooker Headers
1969 Pontiac GTO with 461 stroker Hooker Super Comp headers and DMH cutouts opened. See my other video of the same car running through the Flowmaster mufflers. This vidoe is open Exhaust. Going to add a Victor intake and 850 Demon carb next week. Should have some track video next month.
The wonderful sound of Brians LS2 GTO
6.0 Ls2. AEM Brute force cold air intake, custom headers, Magniflow Exhaust. cats are still on, will be taken off after she goes through the emissions test.
2004 GTO HPE S-Cam (Cold Start) Cut-Outs Open
HPE S-Cam (238/240 .605/.609 112 LSA)
TCI 3000+ Stall
Trans Go Shift Kit
ASP UD Pulley
FAST 90/90
FAST Fuel Rails & -6AN Lines
K&N 57 CAI
JBA Headers
JBA Catted Mid Pipes
StolenFox H-Pipe
QTP Cutouts
IMCO Exhaust
