BMW M5 Street Drift! Giorgi Tevzadze(NeedForDrive.com) & Eric Davidovich(Smotra.ru) by zaRRubin
Giorgi Tevzadze - BMW M5(OOM-500) & White BMW 3-Series(V8, 4.4)
Goga Toloraia - BMW M5(Red, TOL-600)
1. Method Man - Release Yo' Delf (The Prodigy Mix)
2. Shahmen - Mark (low bass)
3. The Go! Team - Apollo Throwdown (Star Slinger Remix)
4. Depth Charge - Sex, Sluts & Heaven (bordello mix)
5. Swollen Members - Reclaim The Throne
6. Delinquent Habits -- Return Of The Tres
7. Shahmen - Van Gogh's Crows
8. I Monster - Dayderam In Blue
2005 BMW E46 3-Series Control Arm Replacement
Click here for products featured in this video:
In this video we'll show you how to replace the control arms and bushings
in a BMW E46. This job is also similar to other cars in the 3-series
lineup, including the E36.
Wheel Bearing Replacement with Basic Hand Tools
Front wheel bearing replacement on a 2002 Buick LeSabre with basic hand
tools. Please note, this vehicle has the bearing built into the hub. Some
vehicles may have a taper rolling bearing (usually older vehicles have this
setup) or some vehicles may need the bearing to be pressed out of the hub.
In this case, the hub & bearing is all one unit. Don't forget to wear
This video is being performed by an experienced tech. Any attempt to repair
automotive parts and/or systems carries risk of personal injury. Always
adhere and follow safe practices when working on vehicles. Such as, use
safety glasses, jack stands, no loose clothing, etc. No guarantee or
warranty is implied. Use the information in this video at your own risk.
2003 Mazda Front Wheel Bearing Replacement (Press In Type Bearing)
Wheel bearing replacement in a 2003 Mazda Protege 5. Press in style
bearings done without using a shop press. Specific for Mazda Protege, but
many of the techniques will apply to vehicles with pres-in-style wheel
It's a good idea to try to use the bearing-press-kit the way it was
intended. If the bearing doesn't budge, BE CAREFUL using a breaker bar. The
bolt supplied with the press-kit is not very strong...it with probably
shear off the head. Try to give the bearin a few hits with a sledge hammer
as seen in the vid..it will get the bearing moving. Then you can use the
press-kit, and it should finish pressing out the bearing.
Pressing in the bearing with the kit should be no problem.
Top 10 BMW Fails Compilation 2013
Top 10 BMW Fails Compilation 2013
SUPPORT THE ORIGINAL VIDEOS:
Fail compilation Video -BMW Drift Fail
Female, BMW and snow - a terrible combination
Idiot with a BMW https://www.youtube.com/watch?v=YDaHA39EwhQ
Besoffener Idiot - BMW Syndikat Asphaltfieber 2011
BMW Clutch Fail! https://www.youtube.com/watch?v=87HzYTPfi2M
Bmw M6 Fail https://www.youtube.com/watch?v=87HzYTPfi2M
BMW X5 crash at parking https://www.youtube.com/watch?v=3KZRa3sYD-I
Fail drift on BMW E30 https://www.youtube.com/watch?v=KaB7DRBTy74
BMW drift failed auto crash 2012
BMW 740i FAIL https://www.youtube.com/watch?v=JwsI3_7q4JM
bmw s1000rr , bmw 2013, bmw grip, bmw x6
BMW Drift Fail, Idiots with BMW, BMW Clutch FAIL, BMW CRASH, BMW BURNOUT,
BMW COMPILATION, FUNNY BMW FAILS, PARKING CRASH, BMW M6, BMW X5, BMW E30,
BMW 740i, BMW IN WATER
Rear Wheel Bearing Removal With No Special Tools BMW 3 Series
I did the job with no special tools. Well, the only "special" tool I used
is found in your plumbing department.
Bearing Installation Video Here
How to Change a Wheel Bearing (short and fast version)
Wheel bearing replacement, How to change a pressed bearing in a Ford,
specifically a 95 Ford Windstar, but this method will be similar for all
pressed bearing vehicles. The main steps are to take off the spindle nut,
tire, brake caliper, and rotor. Then remove the bolts from the lower
control arm ball joint, tie rod, and strut. Remove the steering knuckle,
then press out the bearing and hub/spindle. Then press in your new bearing
and hub/spindle. This job is a little more complex but can still be easily
done by any amateur mechanic. You will save $400-800 depending on your
**If the video helped, please give it a "thumbs up" and consider
Leave any questions or comments below and I will answer them as well.**
My Facebook: https://www.facebook.com/chrisfix8
My Twitter: https://twitter.com/ChrisFix6
how to remove a pressed front bearing, how to remove a front bearing, 2003
Mazda Front Wheel Bearing Replacement (Press In Type Bearing), How To
Remove Pressed-on Bearings - EricTheCarGuy, Wheel Bearing Removal with
Harbor Freight Universal Tool BMW 325i Rear Front, bearing, press, pressed,
pressed bearing, front bearing, front wheel bearing, diagnose, how to, diy,
ford, windstar, ford windstar, Pressing out a front wheel bearing, harbor
freight, bearing kit, How to: Remove & Install A Truck Hub Bearing Assembly
with Timken, How to remove a rusted wheel hub bearing assembly the easy
way, trick, mazda, ford, lincoln, gm, truck, van, car
Due to factors beyond the control of ChrisFix, it cannot guarantee against
unauthorized modifications of this information, or improper use of this
information. ChrisFix assumes no liability for property damage or injury
incurred as a result of any of the information contained in this video.
ChrisFix recommends safe practices when working with power tools,
automotive lifts, lifting tools, jack stands, electrical equipment, blunt
instruments, chemicals, lubricants, or any other tools or equipment seen or
implied in this video. Due to factors beyond the control of ChrisFix, no
information contained in this video shall create any express or implied
warranty or guarantee of any particular result. Any injury, damage or loss
that may result from improper use of these tools, equipment, or the
information contained in this video is the sole responsibility of the user
and not ChrisFix.
BMW 325 E36
Начинаем тестить машины, от которых
действительно получаешь удовольствие.
Одежда Зумба из США:
По вопросам приобретения данного авто:
AcademeG тру ориджинал групп:
Part 2: Installing shocks, struts and springs on a BMW 3 series 99 thru 05 (E46)
BLOG ARTICLE: http://blog.bavauto.com/14307
"Like" us on Facebook - http://www.facebook.com/BavarianAutosport
"Follow" us on Twitter - http://www.twitter.com/BavAuto
"Subscribe" to us on YouTube - http://www.youtube.com/BavarianAuto
Visit our online store - http://www.bavauto.com/
All of the items shown in these videos are available in our online store at
http://www.bavauto.com/. Need additional tech help? Please visit our tech
blog for thousands of Tech and DIY BMW and MINI articles at:
In Part-2 of this two part series, we will replace the rear shock and
spring. See Part- for the front shock/spring/strut replacement.
The Bentley repair manuals will cover standard shock and spring replacement
for the various BMW and MINI models. This DIY will assume that the DIYer
has the applicable Bentley manual for additional reference as well as
fastener torque values. Note that we will be installing the Bilstein
PSS-10 coil-over kit. However, the procedures would be the same for any
common shock/strut replacement (including installing sport springs, if
• New shocks/struts (Bilstein, Koni, Sachs, etc.)
• New sport or stock replacement springs, if desired (BMW, BavAuto,
• New Shock install kits (compression bumpers, dust shields, spring pads,
• New upper strut and shock mounts
• New strut & shock mount gaskets (as required)
• Rear shock mount reinforcing plates
• Bentley Repair Manual
• BavAuto Non-Marring pry bar set
• 13mm through 18mm ½"drive socket & ratchet set with various extensions
• 4mm through 8mm Allen keys or bits (for ratchet use)
• 13mm through 18mm combination wrench set
• Assorted flat and Phillips screwdrivers
REAR (applies directly to the E46 3-series, but the E36 3-series uses the
same steps and procedures):
1) Safely raise the rear of car, with suspension hanging.
2) Remove the wheels.
3) Place a jack under the lower shock mount eye or the wheel hub assembly.
Slightly raise the suspension (just enough to remove the downward tension
on the shock).
4) Remove the lower shock mount bolt.
5) Lower the jack and allow the suspension to hang free.
6) Remove the trunk side trim panel to access the upper shock mount.
7) Remove the two 13mm nuts from the upper shock mount, at the top of the
8) Lower the shock out of the vehicle.
9) Assemble the new shock with new compression bumper, dust tube and upper
mount. Be sure to re-use the large lower and upper washers for the upper
mount. These washers must cup away from the mount. lower washer cups
downward and upper washer cups upward.
10) If the spring is being replaced, it can be removed BEFORE
re-installing the shock. Have a helper pull downward on the wheel hub
assembly and pull the spring out from between the chassis and the upper
11) Using new upper and lower spring pads, install the new spring in the
same manner as the original was removed. Install the new spring pads, then
install the spring.
12) Install the new shock. Place a new shock mount gasket on the shock
mount and insert the assembly up into the shock tower. If installing a
shock mount reinforcement plate, place the plate over the two shock mount
studs, on top of the shock tower, before installing the two nuts. Install
the two nuts. Install the trunk trim panel.
13) Install the lower shock mount bolt. Be sure to install the washer on
the bolt before installing the bolt. Use the jack to raise the suspension
assembly to align the lower shock mount with the hub mounting point, so the
bolt can be inserted and threaded. Tighten the bolt.
14) Repeat for the other side.
All products noted in this video can be purchased in our online store,
http://www.bavauto.com/, 24 hours a day, 7 days a week. You are also
welcome to e-mail us at email@example.com or call into our headquarters and
speak to our knowledgeable advisors at (800) 535-2002 (Mon.-Thurs. 8AM to
9PM EST, Fri. 8AM to 7PM EST, and Sat. 9AM to 4PM EST).
How to Find a Bad Wheel Bearing - EricTheCarGuy
How to Find a Bad Wheel Bearing - EricTheCarGuy
Well as I said in the video I shot this some time ago but never posted it.
I've been snowed in for a couple of days so I haven't been to the shop to
make some new video so I decided to bring this one up from the vault. The
idea is to give you some basic information on how to find a bad wheel
bearing, replacing it once you find it is another story but diagnosing is
the first step.
Now, another way to find out if you have a limited slip is to jack up both
sides of the car and rotate one of the drive wheels. If the wheel on the
opposite side moves in the same direction you probably have a limited slip
differential. If the wheel spins in the opposite direction you probably
have a regular differential that is not limited slip.
As I said in the video a bunch of times be careful doing this, use the
parking brake and brace the rear wheels with something. I know you'll do
the right thing.
Now on to the recommended channels
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
Visit my Facebook Page:
As always stay dirty
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.