Drag Racing 1/4 Mile times 0-60 Dyno Fast Cars Muscle Cars

BMW Wheel Hub Bearing Replacement : DIY [ How To - Part 1 of 2 ] /// 330i (E46)

(Part 1 of 2) This video demonstrates the DIY steps on how to replace your BMW's Front Axle Hub-Bearing assembly. (This was after I received a few Estimates on cost from different shops including a BMW dealership : between $800 to $1,250 plus tax.) Tools needed: Jack and JackStands Slotted screwdriver Hammer 8mm Hex 10mm deep socket 16mm socket 17mm deep socket Bearing-race Installer Ratchet extension 36mm socket 46mm socket Torque wrench (that can hit 250 ft. lbs) 3-Jaw Puller (locking) Quick Link - Part 2 of 2 http://www.youtube.com/watch?v=VALR5pNoB90 Legal Disclaimer - Do this at your own risk. Follow all Safety Procedures. Wear Eye Protection! Wear mechanics gloves if possible. Not responsible if you break anything (Yourself or Property) This DIY was performed on a 02 BMW E46 330i automatic, alpine white paint, with Sport Suspension Package, you know the drill. So if that is not your vehicle, there might be differences.


 


More Videos...


BMW Wheel Hub Bearing Replacement : DIY [ How To - Part 2 of 2 ] /// 330i (E46)
(Part 2 of 2) This video demonstrates the DIY steps on how to replace your BMW's Front Axle Hub-Bearing assembly. If you have questions on removing a sieged / stuck inner Bearing-race, check out this video: http://www.youtube.com/watch?v=qx9X6Np6_NA Quick Link - Part 1 of 2 http://www.youtube.com/watch?v=OU2xSBvXA5g Legal Mumbo Jumbo Disclaimer - Do this at your own risk. Follow all Safety Procedures. Wear Eye Protection! Wear mechanics gloves if possible. Not responsible if you break anything (Yourself or Property) This DIY was performed on a 02 BMW E46 330i automatic, alpine white paint, with Sport Suspension Package, you know the drill. So if that is not your vehicle, there might be differences.





BMW E36 3 Series Front Wheel Hub Bearing Replacement
Removal and installation of the front wheel bearings also known as wheel hubs on a 1995 BMW E36 325i. This procedure is simular to all BMW's produced from 1991 through 2006 E36 E46 Z3 318 330 323 325 models.





Rear Wheel Bearing Removal With No Special Tools BMW 3 Series
I did the job with no special tools. Well, the only "special" tool I used is found in your plumbing department. Bearing Installation Video Here http://www.youtube.com/watch?v=DX9iCZIVgFY&google_comment_id=z12uzlzhhzn0xv scj22ngfgyskbav3hsv&google_view_type#gpluscomments





Wheel Bearing Removal with Harbor Freight Universal Tool BMW 3 Series Rear Front
I spent about $150 on tools. These tools can be used for any bearings I may need to do in the future. I bought the tools at Harbor Freight.





Part 1 - Bmw 318I E46 Rear wheel bearing replacement





Replacing an Accord Wheel Bearing - EricTheCarGuy
Replacing an Accord Wheel Bearing Ok, here it is finally. A few of you have requested this procedure so here it is. As I said in the video I normally use a different method of removing the hub from the bearing assembly by using a slide hammer. I also normally use a press to reinstall the hub into the new bearing instead of hitting it with a hammer. Life is not perfect and we sometimes have to improvise as I did here. I know a few of you will ask about the size fasteners that I used to hammer the bearing out, I used hardened (8.8) 10x1.25 bolts to do the job. I also promised links to the other videos that relate to this one so here they are. "Oops, Axle Ball Joint Replacement" http://www.youtube.com/watch?v=zd5IcN3yjsg and also "How to Replace Honda Captive Rotors" http://www.youtube.com/watch?v=5xIUAMl-oRQ --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- Thanks again to all that have subscribed and left such great comments on my videos and my channel, you are the best, I mean it. You know the line Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Rear Wheel Bearing Installation With No Special Tools BMW 3 Series
I did the job with no special tools. Well, the only "special" tool I used is found in your plumbing department. Bearing Removal Video Here http://www.youtube.com/watch?annotation_id=annotation_270697&feature=iv&src _vid=DX9iCZIVgFY&v=wKYL9_4mXRI





How To Replace a Front Wheel Drive Axle - EricTheCarGuy
If you start to notice your FWD vehicle clicking when you make a tight turn, you might have an issue with the outer CV joint. If you make a right turn, it's usually the left side that's bad and vice versa. Most axles are easy to replace and the one depicted in this video is fairly typical of what you run into. The main differences come in with how the lower ball joint is attached. I think this part will give you the most trouble. I often get asked about what to torque the axle nut to. To be hones, I don't know. I've only ever run them down with my impact. I've never had an issue doing it that way and I don't think you would either. Just be sure to stake the nut or install the cotter pin and retaining clip if it has one. If you'd like more information on how to deal with suspension noises, check out this article I wrote on the topic. http://www.ericthecarguy.com/faq/diagnosing-noises-in-your-car Video on CV boot replacement: http://www.youtube.com/watch?v=-S-ofMoWsr0 The best place for answers to your automotive questions: http://www.ericthecarguy.com Facebook: https://www.facebook.com/EricTheCarGuy?fref=ts Twitter: https://twitter.com/EricTheCarGuy Google+: https://plus.google.com/100195180196698058780/posts Information on Premium Membership: https://www.ericthecarguy.com/premium-content-streaming-etcg-content Stay Dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Installing BMW front wheel bearing with BMW special tool
I finally got to use a BMW special tool I bought several years ago to install my front wheel bearings. In this clip I show why the tool is needed. FYI: BMW special tools are not sold to the general public. If you go to a BMW parts desk and ask for the part number shown they will tell you to get lost....unless, of course, you have a good relationship with the dealership or the techs that work there. That is how I acquired this tool. There may be other aftermarket equivalents available. Check baumtools.com. Please note: The tool is NOT available for loan, so please don't ask.





BMW E46 AWD 330Xi Wheel Bearing Replacement.
BMW E46 AWD 330Xi Front Wheel Bearing Replacement





How to Find a Bad Wheel Bearing - EricTheCarGuy
How to Find a Bad Wheel Bearing - EricTheCarGuy Well as I said in the video I shot this some time ago but never posted it. I've been snowed in for a couple of days so I haven't been to the shop to make some new video so I decided to bring this one up from the vault. The idea is to give you some basic information on how to find a bad wheel bearing, replacing it once you find it is another story but diagnosing is the first step. Now, another way to find out if you have a limited slip is to jack up both sides of the car and rotate one of the drive wheels. If the wheel on the opposite side moves in the same direction you probably have a limited slip differential. If the wheel spins in the opposite direction you probably have a regular differential that is not limited slip. As I said in the video a bunch of times be careful doing this, use the parking brake and brace the rear wheels with something. I know you'll do the right thing. Now on to the recommended channels http://www.youtube.com/user/realfixesrealfast http://www.youtube.com/user/roadragecustoms --- Click below and Stay Dirty Visit me at EricTheCarGuy.com http://ericthecarguy.com/ Visit EricTheCarGuy Forum http://www.ericthecarguy.com/forum/default.aspx Visit my Facebook Page: http://www.facebook.com/EricTheCarGuy --- As always stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Hub Buster
The best and fastest way to remove the wheel bearing hub assembly The best and fastest way to remove the wheel bearing hub assembly





How To Install Repair Replace Front Wheel Hub Bearing Trailblazer Envoy 02-09 1AAuto.com
http://www.1aauto.com/1A/wheel-bearing-hub-front/Chevy/Trailblazer 1A Auto shows you how to repair, install, fix, change or replace a worn out, vibrating or groaning front wheel bearing hub. This video is applicable to the Chevy Trailblazer and GMC Envoy, years 02, 03, 04, 05, 06, 07, 08, and 09.





13 Hub Shark Product Demo 2





1996 RL Rear Wheel Bearing Replacement -EricTheCarGuy
Visit me at: http://www.ericthecarguy.com/ I get lots of requests to just do straight up repair videos like this all the time and I'm always happy when I can oblige. This wheel bearing replacement is fairly typical for a FWD vehicle so much of what you see here can be applied to other FWD vehicles. There are variations in the way the bearing attaches to the hub however the principals are pretty much the same. You should not need a press to do this, just some basic hand tools and sockets will do, air tools make it easier but you don't need them to get this done. As you can see in the video I ran into trouble but the method I employed can be used if you find yourself in a similar situation. Rotor Screw video: https://www.youtube.com/watch?v=YxQk7Pz_vfc Stay dirty ETCG Due to factors beyond the control of EricTheCarGuy, it cannot guarantee against unauthorized modifications of this information, or improper use of this information.  EricTheCarGuy assumes no liability for property damage or injury incurred as a result of any of the information contained in this video. EricTheCarGuy recommends safe practices when working with power tools, automotive lifts, lifting tools, jack stands, electrical equipment, blunt instruments, chemicals, lubricants, or any other tools or equipment seen or implied in this video.  Due to factors beyond the control of EricTheCarGuy, no information contained in this video shall create any express or implied warranty or guarantee of any particular result.  Any injury, damage or loss that may result from improper use of these tools, equipment, or the information contained in this video is the sole responsibility of the user and not EricTheCarGuy.





Which car is faster? Which Car is Faster?




Similar 1/4 mile timeslips to browse:

2004 BMW 330i : 13.630 @ 99.640
vic, Engine: M54 NA, Tires: toyo proxes 235/40r17


2002 BMW 330i Active Autowerke: 13.900 @ 102.000
CD,


2004 BMW 330i ZHP with Dinan Intake: 14.150 @ 101.500
Alex M.,


2003 BMW 330i with performance package: 14.300 @ 97.000
NA, Engine: 3.0 liter 182 cubic inches Inline 6,


2006 BMW 330i : 14.310 @ 98.010
NA,


2006 BMW 330i ZSP: 14.391 @ 96.203
Matthew Forest, Engine: 3.0L Double Vanos I6, Supercharger: Soon. . . Tires: recently replaced stock OEM runflats (lowered air


2006 BMW 330i ZSP: 14.446 @ 97.130
Matthew Forest,


2006 BMW 330i : 14.510 @ 96.710
NA, Engine: I-6 aluminum & magnesium block/ aluminum head, Tires: 225/40R18 88W; 255/35R18 90W Bridgestone Potenza R


2005 BMW 330i ZHP Dinan S1 Package: 14.560 @ 99.300
David Booker,


2006 BMW 330i : 14.697 @ 94.790
Bensin,


2006 BMW 330i ZSP: 14.700 @ 95.100
Motor Trend, Engine: 3.0 Liter Inline 6,


2001 BMW 330i : 14.760 @ 95.720
ari,


2005 BMW 330i 330 i ZHP (Performance Package): 14.800 @ 93.600
Jon S.,


2006 BMW 330i ZSP: 14.819 @ 93.450
Matthew Forest, Supercharger: soon . . . Tires: Stock


2006 BMW 330i : 14.900 @ 94.100
NA, Engine: 3.0L Inline-6 (255hp; 220lb-ft), Tires: Bridgestone Potenza RE050A (F:225/40R18 R:225/35R1


2005 BMW 330i ZHP: 14.960 @ 93.620
Johnathan Dalen,


2000 BMW 330i : 15.010 @ 94.100
NA,


 


©2014 DragTimes - Disclaimer