How To Install Replace Front Brake ABS Harness Silverado Sierra Suburban 1AAuto.com
1A Auto Shows you how to install, repair, fix, change or replace a bad or broken ABS sensor and harness. This video is applicable to the GMC Sierra and Chevy Silverado and Suburban models, years 99, 00, 01, 02, 03, 04, 05, and 06.
Troubleshooting GM ABS slow speed cut in issue_Part 1 of 2
Part 1 of a 2 part video series: My 2001 Tahoe had an ABS cut in issue on
clean dry pavement when at very slow speeds. I suspected a sensor issue
and documented the process on how to test, remove, clean and re-install the
abs sensors. Also, this video discusses a GM ABS sensor recall. See my
2nd video to show the sensor on the other side and how it differs from this
sensor. 2,500 kms after performing this repair, the ABS has not cut in 1
time when it wasn't supposed to do so... problem solved for $0.
ABS Sensor Removal 2000 Chevy Tahoe
ABS Sensor Removal 2000 Chevy Tahoe.... I tried using the old sensors after
cleaning but it did not work for me. Next day i installed the new sensors
and it works great. no more abs braking under 5mph. Took about an hour to
do both sides without recording it.
Remove/Replace/Rebuild GM 246 transfer case, 2000 Chev Suburban
A step by step video showing how I diagnosed, removed and partially tore
down a damaged GM 246 (NP246) transfer case on a Chev 2000 Suburban 4X4
with the 4L60-E automatic transmission. The video shows details of removal
and installation of the case, though full rebuild details are not shown.
If you decide to inspect your vehicle while in drive with rear wheels
spinning, be wary for your personal safety, since sudden loss of life or
limb may be only inches away.
This video is posted for entertainment purposes and is not an instructional
guide. Do not attempt this at home without professional advice. I am not a
professional mechanic, and any misadventure resulting from your attempt to
repair your vehicle is your responsibility.
ABS Sensor & Tone Ring Repair
MotorWeek's Pat Goss explains how anti-lock brake system (ABS) sensors and
tone rings work and how to repair them. He also shows different types of
brake fluid and recommends when to replace brake fluid.
ABS Sensor Diagnostics, Troubleshooting and Repair
http://www.wellsve.com/ Anti-lock brake system diagnostics and repair. 2002
Honda Accord ABS code 15-1 and PCM code P0135. Step by Step wheel speed
sensor diagnostics and replacement.
"The information presented in this program is based on a specific
diagnostic case and might not directly apply to the vehicle you are
repairing. We do not represent or warrant that the information presented
is complete or error free. Please take all safety precautions. We
disclaim any and all liability for losses, injuries or damages in
connection with your repair."
ABS wheel speed sensor diagnostics
How to properly diagnose an ABS wheel speed sensor problem on a vehicle
with a Generation 3 hub bearing and integrated wheel speed sensor.
Chevy ABS and Brake Dash Light fix
This is how to fix intermittent ABS and Brake dash lights on all Chevrolet
vehicles with the Kelsey-Hayes 325 EBCM module. You may have code C0265
"Electronic Brake Control Module Motor Relay Circuit." The fault is usually
due to corrupted solder joints on the circuit board to which the motor
relay circuit is connected and is easily repaired with additional solder.
The warning lights are intermittent whereas the poor solder joints result
in brief communication interruptions with the relay circuit. The warnings
will extinguish when reset (turning the vehicle off/on) and will illuminate
again once the circuit loses its communications path.
*To address comments/concerns: In the video I use 100% silicone inside the
module instead of silicone heat transfer paste. Thermal transfer paste IS a
silicone product with a wide range of operating temperatures, low corrosive
properties (neutral curing) and conductive fillers. The conditions inside
the module would not remotely exceed the limits of 100% silicone and the
thermal paste was also on the insulated portions of the board....Therefore
it would not be effectively transferring an inordinate amount of heat
anyway. (An insulator, as the name suggests, insulates against the transfer
of heat.) I made a reasonable determination that regular silicone would
suffice whereas the insulated portions of the board would certainly
transfer heat just as efficiently as regular silicone. That board is rather
robust and is installed external to the vehicle in a location that sits
above asphalt roads. That asphalt gets 50°C higher than outside
temperatures. Do the math and you will realize that a heat sink is not
effective when the outside conditions are hotter than internal conditions.
(Some are installed in a hot engine compartment.) That heat sink will
transfer those higher temperatures into the module. How important do you
think the transfer paste is now?
Credit is given to "personalfunfest" for his video describing the issue
(see link below). My video describes how to repair the problem in depth. I
was consuming cough drops while filming so please excuse the sounds and
inability to breathe through my nose. :(
How to Diagnose and Repair a Sticking Brake Caliper
The common braking system uses hydraulic principles to slow or stop your
vehicle. Today's modern auto incorporates electronic technologies working
together with efficient hydraulics to get the job done. Diagnosing brake
problems requires a good knowledge of how the system operates and
experience in the field. This video looks at a Chevrolet Corvette that is
pulling to the left. It had the brake pads and rotors previously changed so
we dive into what is causing the car to pull.
How To Replace Rear Disc Brakes (Full) - EricTheCarGuy
How To Replace Rear Disc Brakes (Full) - EricTheCarGuy
I had to split this one into 3 parts when I first posted it and I'm happy
to bring it to you now in it's full form. Enjoy.
Click below and Stay Dirty
Visit me at EricTheCarGuy.com
Visit EricTheCarGuy Forum
Visit my Facebook Page:
Due to factors beyond the control of EricTheCarGuy, it cannot guarantee
against unauthorized modifications of this information, or improper use of
this information. EricTheCarGuy assumes no liability for property damage
or injury incurred as a result of any of the information contained in this
video. EricTheCarGuy recommends safe practices when working with power
tools, automotive lifts, lifting tools, jack stands, electrical equipment,
blunt instruments, chemicals, lubricants, or any other tools or equipment
seen or implied in this video. Due to factors beyond the control of
EricTheCarGuy, no information contained in this video shall create any
express or implied warranty or guarantee of any particular result. Any
injury, damage or loss that may result from improper use of these tools,
equipment, or the information contained in this video is the sole
responsibility of the user and not EricTheCarGuy.