More Videos...

Saturn Ion ignition switch replace part 5
I have 6 videos Part - 1 - removing the steering column bezel Part - 2 - Replacing the ignition switch and putting the steering column bezel back on Part - 3 - First step of the Pass Lock reset Part - 4 - second step of the Pass Lock reset Part - 5 - third step of the Pass Lock reset Part - 6 - Success.

Saturn Ion ignition switch replace part 2
I have 6 videos Part - 1 - removing the steering column bezel Part - 2 - Replacing the ignition switch and putting the steering column bezel back on Part - 3 - First step of the Pass Lock reset Part - 4 - second step of the Pass Lock reset Part - 5 - third step of the Pass Lock reset Part - 6 - Success.

Saturn Ion ignition switch replace part 1
I have 6 videos Part - 1 - removing the steering column bezel Part - 2 - Replacing the ignition switch and putting the steering column bezel back on Part - 3 - First step of the Pass Lock reset Part - 4 - second step of the Pass Lock reset Part - 5 - third step of the Pass Lock reset Part - 6 - Success.

Repair cvt VT25-E/VT20-E, Saturn, Opel.wmv
http://www.avtoakpp-cvt.com Demonstrated inside the repair of variator VT25-E/VT20-E (continuous variable transmission: CVT), mounted on car Saturn Vue 2,2l 2002-2005 and Ion Quad Coupe 2,2l 2003-2004. Also installed on the car Opel Signum 2004-2007 and the Opel Vectra C 2004-2007. Ремонт вариатора VT25-E/VT20-E. Saturn Vue, OPEL.

Saturn Ion ignition switch replace part 3
I have 6 videos Part - 1 - removing the steering column bezel Part - 2 - Replacing the ignition switch and putting the steering column bezel back on Part - 3 - First step of the Pass Lock reset Part - 4 - second step of the Pass Lock reset Part - 5 - third step of the Pass Lock reset Part - 6 - Success.

How to make a cheap transponder key bypass
How to make a cheap transponder key bypass - Costs under 5 bucks! Save yourself all that money you'd give to the locksmith to repair your transponder chip key anti theft system.

Saturn vue ignition key won't turn
Info on having a key made from a vin number.

Ignition Lock Cylinder Cleaning
Saturn S-series Ignition Lock Cylinder Cleaning

GM ignition switch 10 minute relearn procedure
Doing a 10 minute ignition switch relearn procedure after the battery had went bad. The Body Control Module lost all memory so it needed to relearn the Passlock value inside the ignition switch before security system allowed the vehicle to start. Once the relearn process is complete, you must first turn the ignition switch to the "off" position and then back "on" before attempting to start the engine. http://www.engine-misfire.com/gm-vats-passkey-and-passlock/

How To Replace A Ford Ranger Fuel Injector In 20 Minutes - Fast N' Dirty Wrenchin'
Ford Ranger fuel injector replacement procedure. This was done without removing any of the intake manifold or plenum, which saves quite a bit of time. I don't know if its the Ford factory approved method, but it got my rig back on the road again! This was a 1999 2.5 liter 4 cylinder truck, but the instructions should work on all four cylinder Rangers from 1995 through 2001

General Motors Ignition Lock Cylinder Replacement
Seems confusing, but its not when you get into it. GM lock cylinders have a tendency to wear out to the point where a key is not necessary to start a vehicle. Door lock cylinders work different when they are wore out, in most cases with door lock cylinders the right key wont unlock the door.

2004 - 2006 GTO Ignition Cylinder Replacement
The ignition cylinder is a known defective part on the 2004-2006 Pontiac GTO. If yours hasn't locked up, it will eventually, possibly leaving you stranded. You can buy an "upgraded" cylinder from GM and replace it yourself easily...a little peace of mind.

2004 Saturn Ion Coupe 2.2L Start Up & Rev
2004 Saturn Ion Coupe This 1 has a 2.2L 4 Cyl making 140 HP while paired to a CVT. This is a Coupe but it has 2 small doors that open for rear set passenger. Typical Low Rent Saturn Interior of 2004. Very Creaky & Squeaky plastics everywhere. It is not a small car & can accommodate 4 passengers Rater well, but execution of the car was done poorly.

GM passlock problem
2001 Impala Base 114,xxx miles. Runs & drives perfect, except.... GM replaced BCM computer 9-09. Accomplished nothing. I replaced ignition switch w/NAPA part 10-09-09. Worked great for 2 weeks. Then started having the same ole trouble. I replaced ignition key tumbler switch w/passlock sensor w/NAPA part 10-25-09. No problems until this week 1-13-10. Still doing the same exact thing it was doing before I replaced anything. Hasn't started any day this week. 10 minute wait, etc. will not work. Starts when it wants to. HELP!!! Anyone have any ideas on how to properly repair this chronic problem? ----NOTE----the problem is fixed. Cleaned the contacts on the BCM computer fuse. That's all it took. If your car is exhibiting symptoms exactly like mine did, I'd try that 1st.

How To Install Replace Ignition Key Lock Cylinder Chevy Venture Trans Sport 97-98 1AAuto.com
http://www.1aauto.com/1A/IgnitionKeyLockCylinder/Chevy/Venture/1AIMX00066 1A Auto shows you how to repair, install, fix, change or replace a broken door lock cylinder. This video is applicable to 1997-1998 Chevy Venture, 1997-1998 Pontiac Trans Sport Montana, and 1997-1998 Oldsmobile Silhouette.